TP-Link ADSL2+ Wireless :: TD-W8950ND Modem Router To Stop Dhcp / Dns Provided By Device
Apr 9, 2013
Region : Australia
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.2.9 build 110212 Rel.22296n
I made some changes on my wireless modem router to stop dhcp and dns provided by my device. A server is now doing it, but at the same time I appear to have connection issues where I didn't before. In an attempt to resolve the issues I looked at the System Log and a number of things were coming up that concerned me. These are as follows:
-user: tr69c: Unable to retrieve attributes in scratch PAD
-user: Stored Parameter Attribute data is corrupt or missing
Additionally I'm getting a lot of kernel: Intrusion alerts which I can't determine how serious they are. Where to start tracking down these issues (if they even warrant investigation).
View 1 Replies
ADVERTISEMENT
Dec 21, 2012
Region : Others
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.3.1 build 120406 Rel.32903n
ISP : PTCL
I am trying to establish IPSec VPN Tunnel between Linsys RV082 and TP-Link TD-W8950ND but failed.
View 1 Replies
View Related
May 4, 2013
Region : Canada
Model : TD-W8960N
Hardware Version : V1
Firmware Version :
ISP : Bell Canada
Can I use TD-W8960N an additional router with my ISP bell router. Will it increase my speed and range of internet in my home.
View 1 Replies
View Related
Oct 16, 2012
Region : Egypt
Model : TD-W8961ND
Hardware Version : V3
Firmware Version :
ISP :
my router is placed in my home. i want to access to it with IE from my office.but no luck.also i try to ping the WAN ip address of the router.
View 2 Replies
View Related
Feb 21, 2013
How do i stop a Wireless device from connecting to the router? i attempted to find an answer myself and failed
View 1 Replies
View Related
Nov 20, 2011
How can I configure my TP-Link router TD-W8950ND act as an access point? I'll be connecting it to a main router which is connected to the ISP.
View 1 Replies
View Related
Jan 2, 2013
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
View 2 Replies
View Related
Oct 12, 2012
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
View 6 Replies
View Related
Nov 15, 2012
Region : Thailand
Model : TD-W8961ND
Hardware Version : V1
Firmware Version : 2.0.0 Build 111111 Rel.1111
ISP : 3bb
I have a problem when I am trying to add another static ip address to the list
the message above in title pop up, how can I fix it?
DHCP Table is Full!
View 1 Replies
View Related
Feb 25, 2013
Region : Australia
Model : TD-W8960N
Hardware Version : V4
Firmware Version : TD-W8960N_V4_130205_Beta
ISP : TPG
I have an Optus Home Zone (mobile cell tower) that requires ports open.
Port
123 UDP
500 UDP
4500 UDP
I have assigned the Home Zone a Static IP outside the DHCP range and set the above Ports on the NAT, Virtual servers to that IP address.
I have used nmap to scan the ports and it provides open/filtered status for all of them.
Here is the kicker for me, i use a DGN3500 netgear (which keeps dropping WiFi hence its replacement) and enter the ports and it works straight away. Un plug and put the Tp-Link and nothing.
I use Eset Smart Security, could that be the problem?
View 1 Replies
View Related
Jan 26, 2011
I am trying to create a static route on the TP-Link TD-W8950ND router, however am a little confused about the interface I should use. The default gateway on the route is another router on the LAN. I have a choice to use interface pppoe (telstra), LAN/br01 (bridge) or no interface. I was assuming I didn't need to use any interface as this is not a bridge setup and is on the LAN, but when I select "no interface" it doesn't save the static route settings.Also, when I select LAN/br01, the routing saves but doesn't actually work (tracert shows not going through the right router).
View 1 Replies
View Related
Dec 3, 2012
Region : France
Model : TD-W8968
Hardware Version : V1
Firmware Version : TD-W8968_V1_120926
ISP : SFR
Device in question: siemans C610 IP voip phone
Configuration:
* The C610 is directly connected to TD W8968 via the ethernet port number 3 >> ethernet port number 1 is connected to the devolo homeplug 200AVPLUS . The PC is at the other end of the homeplug network
* The DHCP address starts at 192.168.1.100 - 192.168.1.199.
Symptom:
1. It takes a long time (about 2-3 minutes) for the C610IP to obtain the IP address of 192.168.1.100 after the synchronisation of the ADSL line is finished 2. In the DHCP client list, I could only see the IP address of the PC (192.168.1.101) but not the C610 IP. However, if I type 192.168.1.100, I could access to the configuration page of the C610 IP. - I only managed to see the C610IP once in the DHCP client list.
I tried to unplug -> replug the router but to no avail.
View 2 Replies
View Related
Nov 18, 2012
Region : Italy
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 67406
ISP :
I have problem on router td-w8960n v4 internet speed download is limited a 4 mb in device android e ios wifi connected for test i use application speedtest.net on ipad 3 and samsung galaxy s
View 2 Replies
View Related
Apr 3, 2013
Region : UnitedStates
Model : TD-VG3631
Hardware Version : V1
Firmware Version : TD-VG3631_V1_130108
Does this modem support NAT Loopback? I can't get it to work.If so, why not, can we have a firmware that supports NAT Loop back?
View 1 Replies
View Related
Apr 28, 2013
Region : Others
Model : TD-W8968
Hardware Version : V1
Firmware Version :
I have a problem in the model TD-W8968 of modem.Wireless abruptly stopped Even works must turn off the modem Malk happens sometimes 3 to 5 times
View 1 Replies
View Related
Dec 28, 2012
Region : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : TD-VG3631v1_0.6.0_1.0_up(121214)
ISP : TPG
I've noticed the modem becomes unresponsive under use with torrents and only thing that works is to turn it off & on from power button then works for a few more minutes then crashes again on the latest firmware.
View 8 Replies
View Related
Jan 23, 2013
Region : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : TD-VG3631_V1_130108
ISP : iinet
I have set up this modem correctly as it will occasionally sync and internet will be connected for a short time 5-10 seconds then loses sync.Have asked ISP to check line and they say it is fine. I have upgraded to current firmware but same result.I purchased for wireless N and print server features.Have reverted back to 4+ year old Netgear DG834GV which works perfectly with same cabling, filter etc. ISP suggest connect VG3631 on ADSL 1 but if I need to do that I may as well take it back and buy a cheaper wireless AP.I also set my existing Netgear as modem only and connected to EWAN port of VG3631 and it did the same thing (kept dropping connection), this suggests that it is a VG3631 hardware or software problem (completely separate to DSL/Line issues).
View 2 Replies
View Related
Dec 27, 2012
Region : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : TD-VG3631v1_0.6.0_1.0_up(121214)
ISP : TPG
I've noticed the modem becomes unresponsive under use with torrents and only thing that works is to turn it off & on from power button then works for a few more minutes then crashes again on the latest firmware.
View 1 Replies
View Related
Feb 27, 2013
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : wind infostrada
TD-W8970 Wireless connection problems|
Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Wind Infostrada
That's a wonderful router on the paper! Really it has some problems with the wireless connection and the dhcp server. After 2 days of i must forced to reset the router because it refuse any wireless connection while the internet browsing on the other pc connected via ethernet ARJ45 is very slow.To complete the scenario the router doesn't allow any acces to his console page ..so what's the problem?
I try to change any channel for the wireless without no positive result.I bought it on amazon but if this situation will continue without any solution from tp-link i will forced to send it back with a totally negative feedback on the product.
View 5 Replies
View Related
May 13, 2012
I bought yesterday a wireless modem/router and Tp-Link Adsl2+ N300 Modem Router Td-W8960n.I have 2 laptop computers at home.The first issue I have is that with one of the laptops (quite old - Acer Aspire 2420-2579 with Windows Vista Basic Service Pack 1) I can not connect (wireless) to the internet. It says local access only. However in other countries (IM in NZ) it does connect to internet. It does work when I use an Ethernet cable between my router and the laptop. The second issue is with my other laptop. A HP Pavillion DV-4 windows vista home premium service pack 2. I manage to get wireless access to the internet but every couple of minutes the connections drops and starts again by itself�. After 1-2 min approx�. it is getting pretty annoying!I don�t think it is the routher as I also have an XBOX 360 connectet to the internet usign the same device and works absolutely fine!
View 6 Replies
View Related
Jan 27, 2013
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
ISP : Centurylink
I am replacing my qwest/centurylink actiontec q1000 with the td-w8960n. I have run all the different setups, with the different settings that I have found on the net but to no avail. The one thing I have noticed is that the light for the asdl on the td-w8960n does not come on, but yet when I plug it back into the actiontec it sees it and the internet works. Any reason why the td-w8960n is not recognizing the active dsl line?
View 6 Replies
View Related
Jan 26, 2011
I am trying to create a static route on the TP-Link TD-W8950ND router, however am a little confused about the interface I should use. The default gateway on the route is another router on the LAN. I have a choice to use interface pppoe (telstra), LAN/br01 (bridge) or no interface. I was assuming I didn't need to use any interface as this is not a bridge setup and is on the LAN, but when I select "no interface" it doesn't save the static route settings.Also, when I select LAN/br01, the routing saves but doesn't actually work (tracert shows not going through the right router).
View 4 Replies
View Related
Aug 12, 2008
wrt54g v1.1 After setting up the wireless router, I can use the internet on the pc as well as a wireless device. However after putting my pc in standby mode then back on, I can no longer connect to either. I have to restore factory defaults each time and re-enter all passwords and settings.
View 9 Replies
View Related
Nov 6, 2012
So network was running fine for about a year or so. Network consists of 1 Motorola SB6120 cable modem attached to a D-Link DIR-601 wireless router. All settings were default except for SSID and WPA password. One day I just couldn't access internet anymore. I've narrowed it down to the default gateway that is being given out through DHCP. The default gateway that is being given out is the IP of the modem (192.168.100.1) and not of the Router (192.168.0.1). I can't find any option on Wireless router to be able to force the gateway address when handing out the gateway IP. Theoretically I thought I should be able to put router on same subnet as modem as 192.168.100.2 but that still doesn't work. If I set the IP adresses statically on the PCs and give it the Gateway of the Router everything works fine. I should mention this is for my boss' house and basically I dont want him calling me everytime he has a friend come over and I have to talk em through setting up a Static IP.
And just for an example this is what I get if I use DHCP:
IP Address: 192.168.0.155
Mask: 255.255.255.0
DNS: 192.168.0.1
Default Gateway: 192.168.100.1
And If I want it to work I have to change the default gateway to 192.168.0.1 I've tried updating routers firmware and reset to factory default numerous times. Is it possible for a router DHCP stop working?
View 3 Replies
View Related
Nov 30, 2011
My BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies
View Related
Mar 11, 2013
I tried restarting the router and the computer, but to no avail. I've also tried with another ethernet cable and tried several ports, but that did not work, either. What is interesting is that other computers in the household connect to the router via wire without problems. I suppose that means something's wrong with my computer, however, I do not know what. I have a netgear router which says "N300 Wireless ADSL2+ Modem Router DGN2200v3" on the back. My computer has Windows 7 Home Premium installed. I'm using a DSL connection, and Avast! antivirus.
View 7 Replies
View Related
Apr 13, 2012
I have a Netgear N150 Wireless ADSL2+ Modem Router(DGN1000) which i need to connect for wireless access..My internet connection is a wireless one(antenna connected on roof) connection available to only one computer with an RJ45 LAN.Is it possible for me to connect the router to this LAN cable and get internet on more than one computer at a time?? I have the following information
IP :
Subnet :
Default Gateway :
Primary DNS :
Secondary DNS :
MAC of the Registered Computer :
View 2 Replies
View Related
Feb 24, 2011
The bootloader used by the device is U-Boot, which is also licensed under the terms of the GPL. Sadly these parts are missing from the source code package provided by D-Link. Therefore I am asking you to add the U-Boot sources to the provided archive or post them here in the forum.
View 12 Replies
View Related
Nov 25, 2011
I have a standard home network consisting of internet access provided by my cable company which is then disseminated to a variety of wired and wireless devices via a router.
I would like to create a second wireless network that is separate from my current one. This new wireless network would have extra access controls including access restrictions to some web sites using both IP address restrictions and using the OpenDNS DNS servers.
The picture below illustrates the current configuration. The question is: how can I connect ROUTER B to the internet using my current equipment (without buying another IP address from the cable company)?
W
MODEM --> ROUTER A --> ANTENNA <------> COMP 3
1 2 3 4
| |
| |
COMP 1 <---' | W
| ?? <--> ROUTER B --> ANTENNA <---> COMP 4
COMP 2 <-----' 1 2 3 4
W = WAN port
So, in the above picture, COMP 4 is connected via wireless to this second network and cannot access anything on the first network and uses different different DNS servers.
In case it matters, ROUTER A is a Linksys WRT54GL while ROUTER B is a D-Link DI-624.
View 1 Replies
View Related
Jan 1, 2013
We currently get our internet through a small company that only uses a static IP and I cannot get our WRT160N router installed so I can manually set up our internet connection. Is there any way to install the router without using the CD provided. I keep getting the error code 322 during installation.
View 1 Replies
View Related
Apr 20, 2012
Signed up for Sonic Fusion, received ZTE 831 modem in bridge mode, DHCP off.
Have tried many variations of D-Link settings with WAN DHCP and it just does not get an IP address from the ISP. Unicast on/off, DNS relay on/off, SPI on/off, etc.
With the modem settings unchanged, can plug cable from PC directly into modem. It gets an ISP DHCP and works fine. DNS and internet access work, can surf google.com.
Have an Airlink AR525W wireless router. When it is set to DHCP WAN, it also "just works" when plugged into the DSL modem. It is using the router MAC, did NOT clone the MAC from my PC. The Airlink LAN IP is 192.168.1.1, same as the D-Link. The copy-paste from the Airlink configuration screen:
Connection Type: Automatic Configuration - DHCP
Internet IP Address: 173.228.4.46
Subnet Mask: 255.255.255.0
Default Gateway: 173.228.4.1
DNS 1: 208.201.224.11
DNS 2: 208.201.224.33
DNS 3: 0.0.0.0
MTU: Auto
The D-Link was working fine with ATT DSL and PPPoE (this is in SF Bay Area, 94022), but extremely frustrating that it does not seem work to with Sonic DHCP. Called Sonic support, and was able to confirm that plugging the PC directly into the modem works fine. So it seems there is a problem with the DIR-825 (or configuration of it).
View 6 Replies
View Related
May 2, 2013
I have the WRT400N router with the latest firmware. Recently I have noticed a device in my DHCP that I do not recognize. It is not device I own (believe me, I have racked my brain and confirmed) as it shows as an Acer pc. I cannot ping the IP address however. I have rebooted my router several times thinking maybe it's a former connected device but saved in memory but it keeps coming back. I am thinking possibly it is someone hi-jacking my Internet, but not sure. I am using WEP security but it shows a LAN connection which is strange for a wireless device. The only hard wired pc is my HP.
View 3 Replies
View Related
Jan 10, 2012
I use a wired network connection to my neighbours Vodafone Modem (We share his monthly cost). I also have a TP-LINK 54M Wireless ADSL2+ Router from a previous broadband contract with a landline phone company. Is it possible to reset and configure the TP-LINK Router to act as a relay unit, connected to the network cable, so I can then use my laptop elsewhere in the house?
View 3 Replies
View Related
