The bootloader used by the device is U-Boot, which is also licensed under the terms of the GPL. Sadly these parts are missing from the source code package provided by D-Link. Therefore I am asking you to add the U-Boot sources to the provided archive or post them here in the forum.
View 12 RepliesI have a standard home network consisting of internet access provided by my cable company which is then disseminated to a variety of wired and wireless devices via a router.
I would like to create a second wireless network that is separate from my current one. This new wireless network would have extra access controls including access restrictions to some web sites using both IP address restrictions and using the OpenDNS DNS servers.
The picture below illustrates the current configuration. The question is: how can I connect ROUTER B to the internet using my current equipment (without buying another IP address from the cable company)?
W
MODEM --> ROUTER A --> ANTENNA <------> COMP 3
1 2 3 4
| |
| |
COMP 1 <---' | W
| ?? <--> ROUTER B --> ANTENNA <---> COMP 4
COMP 2 <-----' 1 2 3 4
W = WAN port
So, in the above picture, COMP 4 is connected via wireless to this second network and cannot access anything on the first network and uses different different DNS servers.
In case it matters, ROUTER A is a Linksys WRT54GL while ROUTER B is a D-Link DI-624.
Region : Australia
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.2.9 build 110212 Rel.22296n
I made some changes on my wireless modem router to stop dhcp and dns provided by my device. A server is now doing it, but at the same time I appear to have connection issues where I didn't before. In an attempt to resolve the issues I looked at the System Log and a number of things were coming up that concerned me. These are as follows:
-user: tr69c: Unable to retrieve attributes in scratch PAD
-user: Stored Parameter Attribute data is corrupt or missing
Additionally I'm getting a lot of kernel: Intrusion alerts which I can't determine how serious they are. Where to start tracking down these issues (if they even warrant investigation).
can i merge two sources of bandwidth into one router ?
View 1 Replies View RelatedIn the Firewall Dashboard of my ASA 5580, I get data on every pane, except for the Top 10 Sources and Top 10 Destinations. Why is that, and what do I need to do to get data there?
View 1 Replies View RelatedI recently moved into a new apartment complex where Internet is included with the rent, meaning that I do not have a personal Internet connection. Instead, the apartment company has a general connection along with a router on each floor of the complex. They then wire out from that connection to an ethernet port in each apartment. Because of that, calling the Internet company doesn't work because they can only tell me that the router on my floor is getting an Internet connection (and unfortunately my apartment is too far away from that router to have signal strength to use it for wireless). Most tenants plug their personal routers into the ethernet ports and use them for wireless connection within their apartments.
When I try to plug my router in, I cannot connect. I get an error message saying that there is no Internet connection. When I plug my Mac directly into the ethernet port, I still get no Internet connection. I've even tried plugging my netbook (PC) in, and get nothing. I have tried network diagnostics, I have used multiple ethernet cables, nothing. The previous tenant apparently plugged her router into the same ethernet jack I am using and had no problems. She has been gone for a few months, and now I cannot connect.
I'm trying to make a redundantish office/datacentre connection on the cheap. At the datacentre, we've got a 7301 (12.2(24)T5) and at the office we've got a Mikrotik RB1200 (5.12).The office router has two ADSL connections to two different ISPs, the datacentre router a single GigE to a colo provider. I'm trying to build an IPSec encrypted IPIP tunnel over each ADSL service to a separate loopback interface on the datacentre router, so I can run OSPF over the top for route exchange. I need to use two different loopbacks on the datacentre router so the office router can have a static route for each out each ISP ADSL. But I'm running into issues making encryption work on two different source addresses.Using the 'crypto map xxx local-address Loopback12' command, I can specify the outbound interface for one of the tunnels just fine, traffic moves as expected - while the other tunnel fails to encrypt. But is there a way of having two peers use two different local addresses, or applying two crypto maps to a single physical interface?
View 1 Replies View Relatedwe have a bandwidth pipe terminating on 1841 BVI interface... now we want to limit all the traffic going from inside to WAN circuit to half... for example 10 Mb pipe we want to reduce to 5 mb on bvi interface.. how this can be done .. as of not there is not need to police any specific type of traffic .. this needs to be done for any traffic from inside to outside...
View 1 Replies View Relatedproviding the GPL sources for the DIR-615 rev.C firmware. However, it is incomplete!The bootloader used by the device is U-Boot, which is also licensed under the terms of the GPL. Sadly these parts are missing from the source code package provided by D-Link.
View 5 Replies View RelatedI am having an issue where I can't get to external network sources via my sub interface which is attached to a 192.168.10.X VLAN I created to for Guest wireless traffic. The internal interface is a 10.5.X.X network. I can get out the external interface, but anything that we have A records for such as our mobile iron server that we can hit from the outside via https and an external IP can't be hit from the subinterface at all. Would this be a DNS rewrite issue or inspection problem?
View 3 Replies View RelatedFor the command "monitor session 1 source" in Cat4900 (e.g. 4948), how many source interfaces can be supported per monitor session?
View 1 Replies View RelatedWe are leasing an office space from a building that has it's own network center. This center can be used by each office/company to either house their own networking solutions or utilize their internet access if you plan only to use cloud servers or NAS servers. Our company (4 employees) is using this network center only for internet access with all of our data stored and accessed in our cloud service.We would like to access the internet wirelessly, which building does not provide. We were given one port and shared the link through the use of a switch. So my questions is would an access point add wireless connectivity without any information (ISP?) provided by the network center? I am not sure yet if we will be purchasing a router/AP or device made for to be used as an AP.
View 1 Replies View RelatedWe currently get our internet through a small company that only uses a static IP and I cannot get our WRT160N router installed so I can manually set up our internet connection. Is there any way to install the router without using the CD provided. I keep getting the error code 322 during installation.
View 1 Replies View RelatedI am trying to upgrade/migrate my WCS license file, via XML export, through the Cisco licensing portal and I keep getting the error listed above.
View 1 Replies View RelatedI am a very basic user on the Cisco Switch programming. I was given a Cisco 3750G-48 to tinker with in my home office. I was wondering if someone could lead me to some good sources of information to program and configure this switch? I am wanting to create a GB network in the house with the computers that I have and the storage arrays.
View 8 Replies View RelatedI've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.
View 2 Replies View RelatedI want to know could we change or remove the Gateway (highlight) within of Routing Information Sources in OSPF routing protocol? [code]
View 9 Replies View RelatedCan we use all four E1 (i.e. 8Mbps) connections for IMA on IMA-4E1 card in a CS2811 router. What is the maximum speed supported for IMA service provided?
View 3 Replies View RelatedI have upgraded Cisco ACS from 4.1 to 4.2, I have Cisco Access Control 1113 apliance, as soon as I upgraded I am getting error in failed logs "Authen session timed out: Challenge not provided by client", what is wring with this?
View 4 Replies View Relatedwe have an LMS 3.2 in which it cannot archive the configuration for a couple of routers. The output is the following:
Failed to fetch the configuration. Check the dcmaservice.log for details. TELNET: Failed to establish TELNET connection to x.x.x.x - Cause: connect timed out.
The issue is that i have configured all devices to be accessed through SSH first and then through telnet. I have tested SSH access from LMS with putty.
We have LMS 3.2 software. But the RME module can't running because notification error.
View 4 Replies View RelatedI have a not-so newly installed LMS4.2 Linux appliance. Here is my configuration archive summary:
Config Archival Status
No. of Devices
Successful 7 Failed 1338 Partially Successful0 Total1345 Configuration Never Collected 1338
[Code].....
Which seems to mean that SSH does not work, which is false as I manually connects to the device from the LMS host successfully. Network devices access is authenticated against ACS servers using TACACS+ so there should be no problem with credential discrepency here.
I tried to update Sync-archive for the device but it fails.
View 8 Replies View Relatedconfig collection is failing.in detail its partial success(config fetch is success but archieve is failed).
View 1 Replies View RelatedHow can I configure the CiscoWorks to automatically update the config files when a configuration change occurs.
Like in LMS 2.1:
Resource Manager Essentials > Administration > Configuration Management > General Setup
Change Probe Setup
Listen to Syslog Messages
I have a question about a daily archive sync job. I have the job set to run by device type groups. My question is, when I delete or add devices, will they automatically be added to the job?
View 1 Replies View RelatedI beleive in the past these devices could not be managed bij RME config management, but now it says in the supported device table:The following features are supported:Network Topology Layer 2 ServicesFault ManagementInventory CollectionConfiguration Deploy Protocols: TELNET, SSH, TFTP, RCPConfiguration Fetch Protocols: TELNET, SSH, TFTP, RCP.The password and enable pasword are correct and simply work when I try a telnet from the server.The gui is not CLI but menu driven.RME just says:TELNET: Failed to establish TELNET connection to 10.1.1.7 - Cause: Authentication failed on device 3 times. PRIMARY-RUNNING config Fetch Operation failed for TFTP. Could not detect SSH protocols running on the device.
View 13 Replies View RelatedI've inherited a server running Ciscoworks LMS 4.0 to manage our plethora of switches. Running 'Configuration > Configuration Archive > Synchronization' against a Catalyst 3750 switch called switch1 successfully retrieved the Running, Startup, and VLAN configs.Running the same command the following day on switch1 failed and returned this in the job execution result:Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Admin > Collection Settings > Config > Config Job Timeout Settings I modified the job result wait time setting to be 600 seconds, tried again and received the same timeout failure. I have also seen this same Failed message on other devices, but have never actually received the configs for them, so I feel switch1 is a better place to start.What are the first things I should check in CiscoWorks for a problem like this? Is there a particular software revision I should be on with LMS 4.0? What timeout value should be used for Archive Synchronization?
View 1 Replies View RelatedI am getting some weir behaviour in my LMS 4.2 setup. I am doing and Archiveupdate job and am receiving a partial success for roughly 1400 devices. Here is some output.
Execution Result:
STARTUP
CM0057 PRIMARY STARTUP Config fetch SUCCESS, archival failed for
xxxxxx Cause: CM0210 Unable to generate
processed config Action: Verify that archive exists for device.
RUNNING
[code]...
I went on and checked the dcmaservice log file.I found the following entry at the same time of this particulair job
ERROR,[Thread-72920],com.cisco.nm.xms.xdi.pkgs.SharedDcmaIOS.analyzer.IOSConfigletRules,loadRules,42,Could not locate configlet rule file : com/cisco/nm/xms/xdi/pkgs/SharedDcmaIOS/analyzer/IOSConfigletRules.ser
[ date taken out ],ERROR,[Thread-72920],com.cisco.nm.rmeng.dcma.configmanager.DeviceArchiveManager,archiveNewVersionIfNeeded,1115,CM0210 Unable to generate processed config
I then searched if I had the IOSConfigletRules.set file on the box. And no it is not there. My question is this the reasson that I have som manny partial sucess archive results?
In our organisation we have multiple Nexus 5000 switches, which Cisco LMS 4.2.2 cannot get the running-config and startup-config from with the Archive Management process. When it does try to get them, I get a error as follows:
*** Device Details for SF-DERA-01 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,SCP
[Code].....
Iam using LMS 3.2. In short, there is 2 type of router, 2800series and 2900series. These device already join to TACACS server. When I try to sync archive I got:
- failed on 2900series
- successful on 2800series
I have doing same config (credential, snmp, protocol for sync archive), for those device on ciscoworks but why I find the error??
I have a number of devices such as Cisco Call Manager, or Cisco Wireless Controllers, etc that I want to remain in DCR but would like to exclude from the Config Archive process. Is there any way of excluding an individual device from this process?
View 3 Replies View RelatedWe have LMS 4.1 with more than 150 devices.Config Archive is failed for around 20 device.
11- Cisco VG248 ( Cisco analogue gateway)
7 - Cisco call manager
2 - Wireless Lan controller
For this device- discovery, Inventory Collection ,Fault Discovery, Topology Data Collection ,etc are successfull.