Can we use all four E1 (i.e. 8Mbps) connections for IMA on IMA-4E1 card in a CS2811 router. What is the maximum speed supported for IMA service provided?
View 3 Replies
I cant find the maximum number of vrf supported on a 3925E ?
View 1 Replies View RelatedAnyone know the maximum number of IPv4 routes supported per VRF (using VRF-Lite) on a Cisco 3750E stack (two switches in the stack). The current SDM template is 'desktop'.
View 2 Replies View RelatedHow maximum channel-group supported by VWIC2 1MFT G.703? And the CISCO1941/K9 ?
View 0 Replies View RelatedHow many maximum clients are supported by cisco aironet 1262 AP and also by a 5500 Wireless Controller?
View 4 Replies View RelatedI am trying to find out what the maximum amount of HSRP/Standby groups a Cisco 3945 will support. I found this link that I think says 256 URL.
View 6 Replies View Relatedwhat is the maximum number of AAA clients supported by a single ACS5.3 instance?
View 1 Replies View RelatedI am facing issue while configuring service-policy output command in Cisco 7609-S router with c7600s72033-adventerprisek9-mz.122-33.SRE2.bin IOS. However, in the same series router having IOS c7600s72033-adventerprisek9-mz.122-33.SRC6.bin is supported service-policy output.Both the switch have WS-SUP720-3BXL SUP.
View 2 Replies View RelatedI was wondering if the NM-1HSSI is supported on the cisco 3925. documentation seems to include only till 3800 series but can't find if it's supported or is there an alternative option for 3925.
View 6 Replies View RelatedWhat languages are supported by the product? I mean the web interface. I can not find the information.
View 1 Replies View RelatedI have a 3750 switch (c3750-ipbasek9-mz.122-46.SE.bin) were i want to add bandwitdh limit pr. interface, doing the following:
ip access-list extended customer_A
permit ip any any
class-map match-all BW_10Mbps
[Code]....
When i trie to apply the "service-policy output 10 Mbps" to the interface, it says the service-policy output is not supported on the switch. Is this a software related isue ?
I've just connected via pppoe to a fibre 70/40mbs service but only get around 12mbs bandwidth. The FE4 interface reports running at 100mbs Full Duplex so was wondering if the dialer interface has some kind of limit around 12mbs?
If the router is limited to 10/12mbs of WAN throughout, any similar router with greater WAN throughput more suitable for a fibre service.
I have done new configuration for CPI 1.2. while i tried to start service i got belw error. [code]
View 3 Replies View RelatedI am trying to define a ubr+ service class on PVC for an ATM -SPA (4xOC3 ATM SPA ) but I cannot, I can only implement ubr. According to this link I read that ubr+ is only supported on SVCs. URL
The IOS of my 7600 device is 12.2 (33)SRE2. What I would like to know is there is any other IOS that supports ubr+ under PVCs.
Is the max wireless speed on the cisco 881w 54mbps even though it has 802.11n hardware? What about the 891w ?
View 13 Replies View RelatedI am currently receiving 2.9 Meg download using my Intel 82578DC Gigabit though my Local area network can receive a maximum of 100 Mbps. I am with a network service provider that can give me a maximum of 38 Mbps. What defines the maximum speed I can download at if I am receiving 38Mbps from my supplier though my Network connection driver is only allowing me to download at 2.9Mbps?
View 8 Replies View RelatedI was wondering if theres like a max download speed on my computer, im moving to a new apartment soon and i dont wanna get a 200mbs broadband if i cant utilize it on my pc. [code]
View 7 Replies View Relatedi am using local area connection to connect for the internet and the connection spped is 2mbps and this speed is divided between the 10 users and the downloading speed for my system is slow when others are downloading any files so is there any trik to get the max downloading speed for my system.
View 1 Replies View Relatedhow i can add maximum speed kbps for dialing modem
View 1 Replies View Relatedwhat is the maximum speed of vpn connection (pptp, l2tp)?
View 2 Replies View Relatedi am going to purchase a Simultaneous Dual Band Router with Gigabit Lan. Can anybody tell me whats the transfer speed it got on Concurrent Dual Band 900(450+450) , 750(300+450) and 600(300+300). I am going to use it for hard drive that can network attached or may be just external hard drive via USB interface.
View 2 Replies View RelatedWhat is maximum achievable speed of my e1200v1? Latest firmware is installed. I am using Xfinity Blast (50/10). Wired, i get 52mbps, wireless only 25mbps.I have attempted reflash, WMM disable trick, channel 9 setting and disabling the wireless security completely. Normally, i have my laptop, Droid3 and iPod connect via wireles, but for the sake of achieving max speed, i disabled all but the laptop. wireless connection status displays speed: 144 mbits.
View 9 Replies View Relatedset the max download speed of torrent protocole by my router setup page ?My step father currently downloading with torrent and all the internet in the house is pretty slow so i will love to lower he speed so i can use my internet properly
View 5 Replies View RelatedThe title of the thread says it all, but perhaps it does not speak to the level of frustration my family and I are experiencing with our DSL internet service:� Many simple, easy-to-load sites like Google will not load on the first try. On Safari, the bottom toolbar will say "Connecting to google.com" until I refresh the page or restart the web browser. Internet Explorer and Firefox are no better -- I've triedA two-minute YouTube video will take about 10 minutes to load (if the page loads in the first place, which it often does not). Speed test sites, like speedtest.net, which reported a 0.05 mbps download speed and a 0.20 mbps upload speed, usually do not work. I had to refresh speedtest.net four or five times before the "testing download speed" section worked.
Gmail has become so slow that I have to use the HTML version, and even that will fail to register my commands about half the time.The only way for me to view most webpages in a reliable manner is to Google search for them, then click on the "Cached" page, and then click "Text-only version." Stuff other than text will prevent the page from loading about 50% of the time.We have a Qwest modem but our ISP is called "TIES." We have their "Residential DSL connection," as described here:
my office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies View RelatedFirst-I use a vpn service.I had a netgear router connected to my main computer and had no problems at all.I got rid of the netgear router connected the DIR-615 to my main pc.Configured the router,and everything works ok.I get a signal anywhere in the house,and speeds are fine,as far as the laptop.I dont use a a vpn service on the laptop.Just the regular cable connection.No problems at all.I have my main pc hard-wired to the router.When I connect my main pc using a vpn service my line speed its cut down 80%.I had my main pc connected to a netgear router with nothing else,and my vpn service worked fine.I dont understand why my main pc is not working with the vpn service.The only configuration I did was to forwarded a port to utorrent,and that was not a problem.It works,and port is open.The problem is my speed is cut by 80%.
View 1 Replies View RelatedI try to change modem speed from 1200 to 19200 on aux 0 interface.But I can't save the settings using "write memory" In show running-config, I can see modem speed successfully changed.
Cisco3825's OS information is here. c3825-spservicesk9-mz.124-25b.bin
I have a 100mbps internet connection from my ISP but once the connection hits the ASA the download speed gets reduced to 15mbps. My network is setup as follows: ISP Modem ---- Edge Switch ----- ASA --- Internal Cisco Switches
If I plug my computer into an extra port on the Edge Switch I get speeds around 92mbps with normal traffic still going to the ASA. But when I plug into the ASA and internal switches I have speeds of 15mbps.
I have made sure that duplex/speed match on the links. I have done packet captures and within two minutes I do have several dup acks and retransmissions. The retransmissions don't seem to match the dup acks. (The retransmission is not for the dup ack requested so the dup ack keeps being resent)
The only interface error is on the inside interface which includes 700 overruns in a weeks worth of time.I am not using an IPS/IDS. I do have several vpns on it but was not going through a vpn tunnel. I am also using NAT.I am using an ASA 5510 8.2(1)
I have a trouble to implement dynamic QoS between two sites (Site A, and site B) across low speed WAN link (512k). On each site I have Cisco 1921 router. Most important app is Oracle. Because of slow speed WAN links, I want to avoid exact bandwith reservation for Oracle. I only reserve 5% bandwith for network control(icmp, ssh, telnet...) and want configure next Qos scenario:
1. If Oracle traffic exist on a network, it must have 70% of link speed guaranteed, all other apps (e.g mail, file share, ftp) use rest of the bandwith.
2. If there isn't Oracle traffic on a network, all other apps can use all available bandwith.
Issue descrtption:I used all Cisco guides, but when I implemented this on production it simply didn't work. There is no any significant improvement after implementing this (when I start network file sharing accross wan link, Oracle becomes etremly slow.).Here is configuration wich I trying to implement:
ACL-s and class-maps used to mark traffic:
access-list 119 remark ###QoS-MGMT###
access-list 119 permit tcp any any eq 22
access-list 119 permit tcp any any eq telnet
access-list 119 permit icmp any any
access-list 120 remark ###QoS-DB_ORA###
[code].....
we have a bandwidth pipe terminating on 1841 BVI interface... now we want to limit all the traffic going from inside to WAN circuit to half... for example 10 Mb pipe we want to reduce to 5 mb on bvi interface.. how this can be done .. as of not there is not need to police any specific type of traffic .. this needs to be done for any traffic from inside to outside...
View 1 Replies View RelatedI recently moved into a new apartment complex where Internet is included with the rent, meaning that I do not have a personal Internet connection. Instead, the apartment company has a general connection along with a router on each floor of the complex. They then wire out from that connection to an ethernet port in each apartment. Because of that, calling the Internet company doesn't work because they can only tell me that the router on my floor is getting an Internet connection (and unfortunately my apartment is too far away from that router to have signal strength to use it for wireless). Most tenants plug their personal routers into the ethernet ports and use them for wireless connection within their apartments.
When I try to plug my router in, I cannot connect. I get an error message saying that there is no Internet connection. When I plug my Mac directly into the ethernet port, I still get no Internet connection. I've even tried plugging my netbook (PC) in, and get nothing. I have tried network diagnostics, I have used multiple ethernet cables, nothing. The previous tenant apparently plugged her router into the same ethernet jack I am using and had no problems. She has been gone for a few months, and now I cannot connect.
I am trying to upgrade/migrate my WCS license file, via XML export, through the Cisco licensing portal and I keep getting the error listed above.
View 1 Replies View RelatedThe bootloader used by the device is U-Boot, which is also licensed under the terms of the GPL. Sadly these parts are missing from the source code package provided by D-Link. Therefore I am asking you to add the U-Boot sources to the provided archive or post them here in the forum.
View 12 Replies View Related
