I've just connected via pppoe to a fibre 70/40mbs service but only get around 12mbs bandwidth. The FE4 interface reports running at 100mbs Full Duplex so was wondering if the dialer interface has some kind of limit around 12mbs?
If the router is limited to 10/12mbs of WAN throughout, any similar router with greater WAN throughput more suitable for a fibre service.
Is the max wireless speed on the cisco 881w 54mbps even though it has 802.11n hardware? What about the 891w ?
View 13 Replies View RelatedI am currently receiving 2.9 Meg download using my Intel 82578DC Gigabit though my Local area network can receive a maximum of 100 Mbps. I am with a network service provider that can give me a maximum of 38 Mbps. What defines the maximum speed I can download at if I am receiving 38Mbps from my supplier though my Network connection driver is only allowing me to download at 2.9Mbps?
View 8 Replies View RelatedI was wondering if theres like a max download speed on my computer, im moving to a new apartment soon and i dont wanna get a 200mbs broadband if i cant utilize it on my pc. [code]
View 7 Replies View Relatedi am using local area connection to connect for the internet and the connection spped is 2mbps and this speed is divided between the 10 users and the downloading speed for my system is slow when others are downloading any files so is there any trik to get the max downloading speed for my system.
View 1 Replies View Relatedhow i can add maximum speed kbps for dialing modem
View 1 Replies View Relatedwhat is the maximum speed of vpn connection (pptp, l2tp)?
View 2 Replies View RelatedCan we use all four E1 (i.e. 8Mbps) connections for IMA on IMA-4E1 card in a CS2811 router. What is the maximum speed supported for IMA service provided?
View 3 Replies View Relatedi am going to purchase a Simultaneous Dual Band Router with Gigabit Lan. Can anybody tell me whats the transfer speed it got on Concurrent Dual Band 900(450+450) , 750(300+450) and 600(300+300). I am going to use it for hard drive that can network attached or may be just external hard drive via USB interface.
View 2 Replies View RelatedWhat is maximum achievable speed of my e1200v1? Latest firmware is installed. I am using Xfinity Blast (50/10). Wired, i get 52mbps, wireless only 25mbps.I have attempted reflash, WMM disable trick, channel 9 setting and disabling the wireless security completely. Normally, i have my laptop, Droid3 and iPod connect via wireles, but for the sake of achieving max speed, i disabled all but the laptop. wireless connection status displays speed: 144 mbits.
View 9 Replies View Relatedset the max download speed of torrent protocole by my router setup page ?My step father currently downloading with torrent and all the internet in the house is pretty slow so i will love to lower he speed so i can use my internet properly
View 5 Replies View RelatedWhat s the fabric speed (backplane speed) of a Nexus 2232 10G EX?What is the forwarding rate (Mpps) of the same 2232 FEX?
View 6 Replies View RelatedI just discovered that my wireless download speeds are 5Mbps, compared to 16Mbps if my laptop is connected directly to the modem or wired through the router. Uploads are 2Mbps either way. I have a WRT54GS v.6 with firmware version v1.52.8 which I updated today, completed by setting factory default through the router webpage after I discovered this discrepancy. The firmware update did not improve the download speed appreciably, if at all.Should the wireless connection be that much slower than the wired connection through the router? If not, what sort of issues could I be having to account for this?
I did just replace my modem when I discovered I was having erratic speedtests and that corrected that problem. That is when I became aware of the wireless issue, so not sure how long that has been the case. I have Charter's 16/2 HSI, living in a sparsely populated area with solid internet service. There is no external nor internal interference on this 2.4Ghz band.
I have a Arris DLS with 12 Mbps Download and when I Connect my laptop directly I get the same speed as 12 Mbps but when I do the speed test with my linksys I get only 5 Mbps. How to upgrade to the new WRT54GL or WRT54GS?
View 1 Replies View RelatedRecently my desktop has experienced very slow download speeds (~0.11 Mbps), however the upload speed appears to be in line (~2.0Mbps). These numbers are taken from Comcast's speed test (my ISP). It is obviously a problem with my PC because everything else on the network (PS3, Laptop) have great signals with no problems. I just recently reverted the Desktop back to its factory state, and everything was working fine for a couple of months. The desktop in question uses Vista 32-bit and the Belkin Basic USB Wireless Adapter.
View 1 Replies View RelatedI am using Linksys wirelless G router, will my wired speed on desktop increase when I change to a wirelless N router for laptop and ethernet for wired desk top? I don't need anymore wireless speed but am wondering if I upgrade will my wired desktop pick up more speed.
View 2 Replies View RelatedOn board NIC: Intel 82579V Gigabit Network Controller (asus sabertooth x79 motherboard)I installed the drivers for it from intel's site.f I set link speed to auto (chooses 100mbps full duplex) or 100mbps full or half duplex, any HTTP downloads get slowed to a crawl (30kbps) (steam downloads remain at normal speeds). If I set it to 10mbps full duplex, download speeds jump to normal (500kbps for most HTTP sources)his happens on just this new computer (wired connection), any other computers on the network (wireless) work just fine
View 8 Replies View RelatedI live in the tampa bay area, I have bright house (BHN) as my service provider, which provides a Road Runner Lightning (40/5) package. I previously used BHN's top tier (20/2) back in July (and prior) with no problems.
After converting to Lightning in August of this year (2010). Of course, BHN (and every other provider) wants to force a modem/router down your throat, so I had them bridge it (in short, turn it into a dummy modem with no routing). I had an SMC branded modem gateway at the time. I work from home 2 days a week (so I can spend more time with my kids during morning, lunch, right after work) and this requires me to use QoS to ensure my VOIP work calls don't get dropped, if the family is watching youtube videos or watching netflex.
My network was as follows SMC Modem >WAN IP>>WAN Port>>D-link DIR-655>>Switch Ports>PC1, PC2, PC3
Everything seemed fine (from a usability stand point) till about 2 weeks ago when my upload speed seemed to grind to halt. Normally I was able to upload about 200-300K per second, and I noticed this dropped to about 45K per second during a drop box upload. First thing I did was power cycle both my modem and router (in the proper/usual order). After they both come up, I start using speed test to find out what my upload speeds were. I was getting about 39Mbps down, but only .56Mbps up still. I factory reset my router.... test, similar speeds. Power cycle all computers (just in case), and then modem/router. Tested, similar speeds. Updated the firmware to the latest. Same issue
Called BHN customer service, they factor reset it, but it wasn't in bridge mode. If I by passed the 655, in factory mode (non bridge mode) upload speeds returned to better than expected states. If I bridged the cable modem, upload speeds seemed to crash.
Had BHN replace the modem, seemed fixed for a day, then issue came back. Had them come back out and replace it again, this time with a Motorolla Surfboard modem... same issue. Fine during factory reset, however after they bridge the modem, upload speeds were fine. Told BHN I would take it from there.. Connected up the DIR-655, and upload speeds crashed again. (.6Mbps). Called D-Link Support, and the Chinese English speaking rep seemed to not be listening to me and tried to have me adjust my MTU as well as Wireless settings. Long story short... the rep was a level 0 id10t and I hope D-link will consider hiring better employees/contractors. So I was all about to give up and replace it with a DD-WRT capable router (which it takes me a lot to want to swap hardware), when I discovered the wan shaping was on. Which I thought to myself... nah... QoS has never messed up before... why would it be the cause. Turned off wan shapping... and voila. Issue seemed to be insta-resolved.
Unsatisfied with that... I decided to dig a lil deeper. I turned on Wan shaping again, but decided to set the settings manually instead of auto detect.
Here are the settings I used... (Advanced Tab>QoS)
Enable Traffic Shaping - Checked
Automatic Uplink Speed - Unchecked
Manual Uplink Speed - 5000
Connection Type: Cable or Other Broadand Network
Enable QoS Engine - Checked Automatic Classification - unchecked (this checked seemed to affect my upload speed by about 5-10% during testing) Dynamic Fragmentation - unchecked (this checked seemed to be the worse enemy for upload speed)
While I know I'm not any network guru (still have to use a subnet calculator for subnetting), I think I did a pretty good job drilling down the issue (once I got passed my service provider replacing modems).
Anyways, I've had overall good luck with D-Link products, even have a 5 port 10/100 switch (all metal) from 1998 that works great. Hopefully, D-Link will just either put more documentation on the web, or hire better employees.
Are the users' download speeds depend on the hosting company's owner's internet speed? Let say if I was running my own server with my internet speed 1mb and LAN 100mbps, are my clients' download speeds restricted to maximum 1mb of any content from my server?
View 3 Replies View RelatedI just upgraded my internet plan over the phone from 10mbps to 20mbps + WiFi. Now my connection speed is slower then it was before.
View 2 Replies View RelatedI need to provide a router to connect Internet circuit and run IPsec to MPLS network. Circuit is 10Mbps.
What is the max a Cisco 881 can handle if running IPsec?Also, if you are aware of any branch router (1941) which allows connection to future 4G LTE .
how much distance can we have VSL,
I have 2 x 6509 serving as redundant switches and now i plan to upgrade to VSS, but both switch are 2KM away from each other.
What are the max number of T1's that can be bundled on a 2911 router?
View 0 Replies View RelatedWe are looking at providing an ISR 819 for one of our customers using FTTC & 3G for failover .. However, I cant seem to find any recommended throughput guidence for the device? We could be looking at up to 80Mbps via the ethernet interface and I just dont know if the device will cope?
View 4 Replies View Relatedon 3750X how many interfaces can be configured with PIM activated on ?
View 2 Replies View RelatedWe have a PIX 535 with unlimited lisence, it has 1,048,953 in use connections because the timeouts have been changed to 24 hour. I am addressing this issue but was wondering why its so high when the max concurrent sessions is supposed to be 500,000 as listed in the product spec. Also when it reaches it max and cannot allocate a connection what PIX syslog error message number would it send?
View 1 Replies View Relatedwhat is the maximum user IDs that I can create to the ACS server? The client have an ACS appliance with version 5.2.
View 2 Replies View RelatedI'm using a Catalyst 4500 switch (C4507R+E) with Sup 7E. Cisco Datasheet of this switch says that it can learn maximum 256K IPV4 routes. Currently it just learns 10330 ipv4 routes. However when I show platform hardware ip route summary, it seems that the FIB is just free 100K routes as below output:
Entity total used free util%
Entries 260096 10332 249764 3
UC Ipv4 110592 10331 100261 9
unused 147456 147456 0 100
My question is: Can I make use of all 147456 unused routes? Or these ones have to use for any special purpose?
I used 2 PC with gigabit NIC, use cat6 with short cable i've got speed 1000Mbps, but with longer cable(around 30meters) speed is 100Mbps. I'm looking forward to seeing from you soon.
View 1 Replies View Relatedwhat is the maxium range of a router?
View 3 Replies View RelatedBuilding a dmvpn network with 2911 hub router.Anyone have a clue how many simultaneous vpn connections can be used? The amount of transferred data is very small.
View 1 Replies View RelatedSomeone has mentioned only 25 nodes are supported by the 1524SB and that one AP gets bogged down by 20 nodes or more.
View 0 Replies View RelatedWhat is the maximum possible ISDN calls on Cisco 7206VXR router using PRI links and PRI supported cards.
View 7 Replies View Related