Cisco WAN :: C4507R+E - Maximum Routes Sup 7E?
Mar 10, 2013
I'm using a Catalyst 4500 switch (C4507R+E) with Sup 7E. Cisco Datasheet of this switch says that it can learn maximum 256K IPV4 routes. Currently it just learns 10330 ipv4 routes. However when I show platform hardware ip route summary, it seems that the FIB is just free 100K routes as below output:
Entity total used free util%
Entries 260096 10332 249764 3
UC Ipv4 110592 10331 100261 9
unused 147456 147456 0 100
My question is: Can I make use of all 147456 unused routes? Or these ones have to use for any special purpose?
View 1 Replies
ADVERTISEMENT
Feb 21, 2012
Anyone know the maximum number of IPv4 routes supported per VRF (using VRF-Lite) on a Cisco 3750E stack (two switches in the stack). The current SDM template is 'desktop'.
View 2 Replies
View Related
Apr 8, 2011
Is there a way in EIGRP to prefer external routes versus internal routes. EIGRP always picks up internal routes as long as they are available, no matter if external routes have better metric. Our Scenario is that we have DMVPN hub and spoke topology running EIGRP 101. The Core routers also on EIGRP 101 prefer EIGRP 101 routes. We have the new MPLS network running BGP and redistributing these BGP routes into EIGRP 101. The core routers prefer EIGRP 101 routes (internal) to redistributed BGP (external) routes.
View 9 Replies
View Related
Jun 12, 2013
we have 2 Cisco C4507 Switches working As Core Layer, but the CPU Utilization is about 54% most of the time and sometimes it goes up to 70% or 80% also.
which services are causing this utilization. [code]
View 4 Replies
View Related
Feb 26, 2012
Customer has WS-X4013+ supervisor engine and want to use as redundant SUP for WS-C4507R-E. Is it possible to configure EIGRP then? The customer already has WS-C4507R with SUP WS-X4013+ and has configured EIGRP.
View 5 Replies
View Related
Apr 25, 2012
I have a WS-C4507R-E switch. The current SW Ver. on it is 12.2(53)SG4-IP-BASE-CRYPTO. I have been tasked with making sure all of our switches and routers have the most current IOS running on them.
So, with that, when I look at the software available for download for my particular switch, there are several. Some of the IOS description makes sense, but not even sure really if I do understand what I am looking at. How do I know which software package I need to use to upgrade the switch? This is our core switch..while yes, I would certainly back up the current switch, I would hate to be responsible for taking down the entire network due to a unfortunate misunderstanding of what I thought I read, even is it only last as long as it takes to restore from the back up.
View 7 Replies
View Related
Aug 31, 2012
I have a switch WS-C4507R + E, added two SFP SFP-10GBase-SR, and they stayed with inactive status, activate these interfaces in 10Gb.
SWC-DC01#sh interfaces status module 4
Port Name Status Vlan Duplex Speed Type
Te4/1 connected trunk full a-1000 1000BaseBX10-U
Te4/2 notconnect 1 full auto No XCVR
Te4/3 inactive 220 full auto 10GBase-SR
Te4/4 inactive 220 full auto 10GBase-SR
[code]......
View 1 Replies
View Related
Aug 24, 2012
A customer wants to upgrade an IOS Base (cat4500-ipbasek9-mz.122-25.SG4.bin) of a WS-C4507R Cisco, for a IOS that have a enterprices functionalities.We install an IOS cat4500e-entservicesk9-mz.122-53.SG5.bin, but we had the following results:
config-register = 0x2102
Autobooting specified file using Variable BOOT .....
Current BOOT file is --- bootflash: cat4500e-entservicesk9-mz.122-53.SG5.bin
[Code].....
View 1 Replies
View Related
Jul 25, 2012
We currently have an environment with a 4507 as the core switch connected to four stacks of 3750e's in the wiring closets. A pair of Nexus 5548UP's also hangs off the 4507, but at the moment more or less dedicated to a certain purpose..The 5548UP's have the L3 daughter card installed.
My question is: Can a pair of Nexus 5548UP's do a C4507's job? Would we be able to decomission the 4507 and replace with the existing 5548UP's + FEXes?
View 1 Replies
View Related
Jan 4, 2012
I tried to discovery WS-C4507R+E devices with lms 4.0 but the devices result unknown, any package to install to discover these types of device?
View 1 Replies
View Related
Jul 5, 2012
We are getting the HIGH CPU process due to Cat4k Mgmt Lopri with both core Switches installed at the Customer site. [code]
View 5 Replies
View Related
Jan 14, 2012
I am using radius authentication on C4507R+E with supervisor card 6L-E and IOS 15.0.2(SG1). It works perfectly but all radius messages appear in the console. Radius is very verbose, I can't use console because of the significant number of messages and I am worried about switches performances. I add that all debug commands are disabled.
View 1 Replies
View Related
Aug 13, 2012
I'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at a time it seems to work. But I really don't want to configure 6 fully populated switches one port at a time. We also have a lot of 3750's and they gave me no problem using a port range. [code]
View 4 Replies
View Related
Feb 4, 2013
We have a BGP / OSPF configuration as shown in the topology picture. When the connection towards Internet is taken down, we expect the traffic to be forwarded toward WAN 2 (preferred) or WAN 1. The problem is that the BGP learned routes disappears when the Internet connection is taken down. The IP routing table on R2 only shows internal networks and the networks between R2 and WAN 1 and 2. No routes to internet is shown. We run "show ip bgp neighbors <ip-to-wan-1-router> received-routes" it contain internet routes. And when we run "show ip bgp neighbors <ip-to-wan-1-router> routes" it contains no routes at all.
View 2 Replies
View Related
Jul 24, 2011
How many routes support 7206VXR with NPE-G2?
View 2 Replies
View Related
Jan 23, 2011
I want to know the number of routes supported by CISCO3825-HSEC/K9(512MB DRAM).
View 2 Replies
View Related
Feb 15, 2011
I have an ASA 5510 that is configured for a remote access VPN
When users login, they are given an address from a locally defined pool (172.16.101.1-254 /24). Users can log in fine.
I have enabled EIGRP on the ASA and I have configured the following to be advertised:
1. 0.0.0.0 (default)
2. 172.16.100.0 /24 (dmz network)
3. 172.16.101.0 /24 (vpn pool)
I have also enabled reverse-route injection.
The problem I am having is that the VPN pool network is not being advertised via EIGRP, but the other networks are.
The other issue I am having is that even though I have created access-lists that allow the inside network (10.0.0.0) to ping the DMZ interface (172.16.101.1) on the ASA, the ASA is not allowing it. I have also created an ACL that allows the DMZ interface to ping inside, but this fails as well.
View 1 Replies
View Related
May 20, 2012
I am running an ASA with 8.4(3) and am trying to setup a dynamic VPN tunnel. We are having a business reason to establish a VPN tunnel to customers who do not have nailed down IP addresses. Now I found a number of documents that outline the steps involved. It seems the basic steps were to Establish a regular tunnelAdd dynamic crypto mapAssign the dynamic crypto map to the tunnel created under step 1. While this sounds pretty straight forward and simple, while prepping for doing just this I hot a road block while thinking it through. In order for my ASA to put anything into the tunnel it has to have a route to the remote network pointing at my VPN peer at the end of the tunnel. How do I do this in a dynamic tunnel? How do I add a dynamic route so the ASA knows which tunnel to stuff the traffic into? How do I stop the traffic from just being send to the Internet?
View 1 Replies
View Related
Dec 12, 2012
I'm trying to set up a Cisco ASA 5505. I'm mainly setting things up through ASDM but I also have console access. Right now while I'm setting it up I have the outside/Vlan2 port attached to my existing network and a laptop connected to the inside/Vlan1 port. More info about that:
interface Vlan1
nameif inside
security-level 100
[Code]....
Before I added that last "0.0.0.0" entry, the ASA would not see anything on the internet. Now I can ping any external IP address from the router's console. However, the laptop I have connected to the 'inside' port still cannot reach any IP address outside the 10.10.153.0 network. Every time I try to add a similar route for the 'inside' interface, I get the following error: "You have another route configured for this network any which has same gateway 10.10.152.1 and same metric 1. You cannot add a duplicate route." I know I'm misunderstanding something here. In order to make devices connected to the 'inside' port connect to the internet, I need to set up a new route that will direct these devices to 10.10.152.1, right?
View 9 Replies
View Related
Jul 5, 2011
For ASR1000 to support 4M routes, RP2 must be used.
1) RP2 need to have 16GB memory in order to support 4M routes?
2) Need to use ESP20/40 together with RP2?
3) If RP2 + ESP10, supporting route table size down to 1M?
4) 4M routes is shared for both IPv4 an IPv6?
5) SIP card will affect route table size?
View 1 Replies
View Related
Nov 15, 2011
In my live VPN concentrator at work, my 5520 is showing a static route for each VPN client that is connected to my SSL vpn right now. This kind of confused me because wouldn't only one route to the address pools subnet be needed for my vpn users?
View 12 Replies
View Related
Apr 2, 2013
viewtopic.php?f=33&t=24000
How can you remove these "L" routes in routing table?
View 6 Replies
View Related
May 10, 2013
I bought the SG300-10 Switch a few days ago and updated it to firmware 1.3.0.59, but i think there's a bug in this firmware. If I go to "IP Configuration" IPv4 Routes" in L3 Mode nothing is displayed. In the log file i see that:
21474773112013-Mar-16 09:51:34Error%HTTP_HTTPS-E-DIAGNOSTICS: ERROR - in <RL_vtLeadTableGet> tag, can not find the table rlInetRoutingDistanceTable in the MIB. 21474775182013-Mar-14 22:39:22Error%HTTP_HTTPS-E-DIAGNOSTICS: ERROR - in <RL_vtLeadTableGet> tag, can not find the table rlInetRoutingDistanceTable in the MIB., aggregated (1)
Reset of the Switch doesn't work.
View 4 Replies
View Related
Jan 27, 2012
We have a Cisco 7301 concentrator, well two of them in HSRP configuration. We have multiple VPN's setup on that router (crypto map based). Recently we noticed the following:
- There is one IP address that has hundreds of static routes for some reason
- VPN for this customer is working, but I'm trying to find out why this is happening.
Here is how it looks like: S 0.0.0.0 0xF5FFFF2C [1/0] via "ip-address".There are hundreds of entries for a single IP there.
View 2 Replies
View Related
Jul 24, 2011
I am working on a network that has four nodes/Currently I have RIP running in between R1 and R2, and between R3 and R2. These are shared and R1 can access R3 just fine.R3 is running BGP and communicating with R4.R3 can ping everything in R4's network with no difficulty.Currently R3 is not rebroadcasting the BGP routes into RIPv2 as needed.I have tried clearing my BGP session and am still not able to get the BGP routes from R4 to R1.
View 1 Replies
View Related
Mar 6, 2012
<RouterA1>-Network2-<RouterA2>-AS65100-<RouterB1>-Network1-<RouterB2>
| |
| AS65101 |
<Router1>--------------------Network3----------------------<Router2>
Routers A1,A2,B1,B2 are in AS 65100
Routers 1 and 2 are in AS 65101
Routes from the network2 to network3 should go through RouterA1-Router1
Routes from the network1 to network3 should go through RouterB2-Router2
As for now all routes within AS 65100 to AS 65101 goes through RouterB2/Router2
View 3 Replies
View Related
Jun 29, 2011
a customer of us asked if C2911 (to be bought) is ok for partial BGP routes.This is the situation: 2 cisco 2911, each peering with 3 other AS (AS1, AS2, AS3), and maybe, in the future, at a small IXP (AS4, AS5, AS6, AS7).They will accept defaults plus partial routes from upstream AS1, AS2, AS3.When deployed at the IXP they also will accept partial routes from AS4-7.So, is 2911 ok for that configuration?the default route is included in the first row of as-path, isn't it?I have no experience with partial routes, only with full (for our datacenter) and default only (for other customers).
View 5 Replies
View Related
Apr 7, 2013
i been filterin LSA type 3 and the table route localy routes en ospf v2 ipv4 whit the commands distribute-list , area filter-list route-maps ACL and prefix-lis ¿but how can i do the same filterin in ipv6 whith OSPFv3?
View 2 Replies
View Related
Feb 7, 2012
We are planning to run BGP on our pair of 3560G switch, I would like to know how many bgp routes it can support? it currently running on advance IP service.
View 4 Replies
View Related
May 6, 2012
I need to use IP SLA to monitor remote routes on CAT6500
CAT6500 is running "sup-bootflash:s72033-jk9o3sv-mz.122-18.SXD7b.bin" on SUP720
Feature Navigator said it is
ENT FW W/MPLS/IPV6/SSH/3DES After drill down into feature set I found that this version support for IP SLA such IP SLAs - ICMP Path Echo Operation
BUT, back to console I can not do such (config) ip sla command (not found cmd CAT6500(config)# ip sla 1) What I did wrong or others cmd imply this ip sla process?
View 1 Replies
View Related
May 4, 2011
There is a strange problem with :c880data-universalk9-mz.150-1.M4.bin IOS. I can't ping gateway IP address and "sh ip route" does not show any routes.
interface FastEthernet4
ip address a.b.82.66 255.255.255.0
duplex auto
speed auto
View 7 Replies
View Related
May 19, 2013
We've got a fairly plain-vanilla VPN configuration on a C3660 router running IOS 12.3(26) so that our employees can initiate VPN sessions to our office using their Windows or Linux workstations. In a typical windows L2TP VPN configuration, the default route is set to the VPN server, and no other routes are passed to the clients, which means that if the client disables "use default route" setting, even getting to the office network fails.
I know there's a way to do this, but I haven't found it yet. What I want to do is pass local routes to the client so that only those routes transit the VPN, and permit the clients to use their own default routes.
View 1 Replies
View Related
Jan 31, 2013
Is there anyway I can see how many routes are internal to an AS?
So, something like "show ip route in AS1234" where AS1234 is the local AS number. All internal routes within AS1234 are being parsed around via iBGP, but AS1234 has a full BGP table from upstream provides so "show ip route" shows all local and global routes. How can I see all the routes within the local AS only?
View 2 Replies
View Related
