Cisco Switching/Routing :: Inactive Interface On The WS-C4507R+E?
Aug 31, 2012
I have a switch WS-C4507R + E, added two SFP SFP-10GBase-SR, and they stayed with inactive status, activate these interfaces in 10Gb.
SWC-DC01#sh interfaces status module 4
Port Name Status Vlan Duplex Speed Type
Te4/1 connected trunk full a-1000 1000BaseBX10-U
Te4/2 notconnect 1 full auto No XCVR
Te4/3 inactive 220 full auto 10GBase-SR
Te4/4 inactive 220 full auto 10GBase-SR
[code]......
View 1 Replies
ADVERTISEMENT
Jan 22, 2013
We have 3 Cat 4500 switches on three floors teh 3rd floor switch connects to the 2nd and 4th floor switches ,but we are receiving an alert from monitoring tool that " Interface(314) Backup-1Gb-Ring is Down at least 2 min on Switch: SOM500-4510-3FL the following output from "sh int status module 1 " shows the int 1/3 and 1/4 are 'inactive'local IT guy said If the status is inactive,the ports cannot be used and might lost the capability when he added 48-port blade into the 10th slot.
2nd Floor
Port Name Status Vlan Duplex Speed TypeTe1/1 SOM500-Core1 connected trunk full 10G 10GBase-LRMTe1/2 SOM500-Core1 connected trunk full 10G 10GBase-LRMGi1/3 Backup-1Gb-Ring notconnect 1 full 1000 1000BaseSXGi1/4 Backup-1Gb-Ring connected trunk full 1000 1000BaseSX
3rd FloorPort Name Status Vlan Duplex Speed TypeTe1/1 SOM500-Core1 connected trunk full 10G 10GBase-LRMTe1/2 SOM500-Core1 connected trunk full 10G 10GBase-LRMGi1/3 Backup-1Gb-Ring inactive 1 full 1000 1000BaseSXGi1/4 Backup-1Gb-Ring inactive 1 full 1000
[code]....
View 6 Replies
View Related
Apr 25, 2012
I have a WS-C4507R-E switch. The current SW Ver. on it is 12.2(53)SG4-IP-BASE-CRYPTO. I have been tasked with making sure all of our switches and routers have the most current IOS running on them.
So, with that, when I look at the software available for download for my particular switch, there are several. Some of the IOS description makes sense, but not even sure really if I do understand what I am looking at. How do I know which software package I need to use to upgrade the switch? This is our core switch..while yes, I would certainly back up the current switch, I would hate to be responsible for taking down the entire network due to a unfortunate misunderstanding of what I thought I read, even is it only last as long as it takes to restore from the back up.
View 7 Replies
View Related
Aug 24, 2012
A customer wants to upgrade an IOS Base (cat4500-ipbasek9-mz.122-25.SG4.bin) of a WS-C4507R Cisco, for a IOS that have a enterprices functionalities.We install an IOS cat4500e-entservicesk9-mz.122-53.SG5.bin, but we had the following results:
config-register = 0x2102
Autobooting specified file using Variable BOOT .....
Current BOOT file is --- bootflash: cat4500e-entservicesk9-mz.122-53.SG5.bin
[Code].....
View 1 Replies
View Related
Jul 25, 2012
We currently have an environment with a 4507 as the core switch connected to four stacks of 3750e's in the wiring closets. A pair of Nexus 5548UP's also hangs off the 4507, but at the moment more or less dedicated to a certain purpose..The 5548UP's have the L3 daughter card installed.
My question is: Can a pair of Nexus 5548UP's do a C4507's job? Would we be able to decomission the 4507 and replace with the existing 5548UP's + FEXes?
View 1 Replies
View Related
Jul 5, 2012
We are getting the HIGH CPU process due to Cat4k Mgmt Lopri with both core Switches installed at the Customer site. [code]
View 5 Replies
View Related
Jan 14, 2012
I am using radius authentication on C4507R+E with supervisor card 6L-E and IOS 15.0.2(SG1). It works perfectly but all radius messages appear in the console. Radius is very verbose, I can't use console because of the significant number of messages and I am worried about switches performances. I add that all debug commands are disabled.
View 1 Replies
View Related
Aug 13, 2012
I'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at a time it seems to work. But I really don't want to configure 6 fully populated switches one port at a time. We also have a lot of 3750's and they gave me no problem using a port range. [code]
View 4 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
Mar 12, 2013
Quick question here. Using 3750E series switches with multiple VLANS configured. These switches serve as our 'core'. I have SVIs configured for the different VLANs and add inbound ACLs in each of the SVIs to control traffic between VLANS. This switch also terminates a P2P Ethernet link which connects to our Colo facility. The port used for this is configured as an L3 port. I noticed today that I was able to send traffic across this L3 link that I thought should have been blocked by an ACL I had in place but it wasn't. So the traffic flowed from a port in say VLAN 20 across this L3 link (assigned with an IP address). Would this traffic flow not cause traffic to be checked against an ACL applied in the inbound direction on the SVI of VLAN 20 (int vlan 20)? Traffic does get checked when routing between SVIs. Why would it not get checked when routing between SVI and L3 interface?
View 2 Replies
View Related
Mar 7, 2012
On a pair of my CISCO7609-s (engine:sup720-3B IOS Version:12.2(33)SRD4),some interfaces is configured as routing interface but also them are attend MSTP caculation and i really caught BPDU packet go out from these ports. [code]
View 1 Replies
View Related
Feb 26, 2013
We got a layer3 switched network, with one vlan for every switch, routed by a cat4006. [code] So can we put some ports on different switches in, let`s say vlan 50, with different ips? For example, Port 0/3 on Switch 1 and 0/8 on Switch 2, but keeping the ip of the "old" vlan? Or is it necessary to configure a specified vlan interface with ip-adress for every vlan if i want to route it?
View 4 Replies
View Related
Jan 7, 2012
I am a recent student to Cisco products and I have purchased some (what I thought was good) lab equipment to learn with on a budget. What I have is a 2948G switch and a 2620 router. My issue is this: the router has only one fast Ethernet port. Is it possible to use V LAN's and V LAN Interfaces on the router and switch to somehow emulate a second interface to connect to a WAN or sub net?
View 11 Replies
View Related
Jun 12, 2013
we have 2 Cisco C4507 Switches working As Core Layer, but the CPU Utilization is about 54% most of the time and sometimes it goes up to 70% or 80% also.
which services are causing this utilization. [code]
View 4 Replies
View Related
Mar 10, 2013
I'm using a Catalyst 4500 switch (C4507R+E) with Sup 7E. Cisco Datasheet of this switch says that it can learn maximum 256K IPV4 routes. Currently it just learns 10330 ipv4 routes. However when I show platform hardware ip route summary, it seems that the FIB is just free 100K routes as below output:
Entity total used free util%
Entries 260096 10332 249764 3
UC Ipv4 110592 10331 100261 9
unused 147456 147456 0 100
My question is: Can I make use of all 147456 unused routes? Or these ones have to use for any special purpose?
View 1 Replies
View Related
Feb 26, 2012
Customer has WS-X4013+ supervisor engine and want to use as redundant SUP for WS-C4507R-E. Is it possible to configure EIGRP then? The customer already has WS-C4507R with SUP WS-X4013+ and has configured EIGRP.
View 5 Replies
View Related
Aug 30, 2010
i've got a Cisco 877 router connected to an ADSL link. i'm using the show dsl interface atm just to have a look on its performance. i've tried to search on Cisco website on how to interpret the output but a blog gave me more info [URL]. My question now is, what readings do i consider? is it on the left (ATU-R) or on the right (ATU-C)?
877ROUTER#sh dsl int atm0 ATU-R (DS) ATU-C (US)Modem Status: Showtime (DMTDSL_SHOWTIME)DSL Mode: ITU G.992.1 (G.DMT)ITU STD NUM: 0x01 0x01Vendor ID: 'ALCB' 'ALCB'Vendor Specific: 0x0000 0x0000Vendor Country: 0x00 0x0FCapacity Used: 31% 85%Noise Margin: 34.0 dB 10.0 dBOutput Power: 16.0 dBm 12.0 dBmAttenuation: 10.0 dB 6.0 dBDefect Status: None None Last Fail Code: NoneSelftest Result: 0x00Subfunction: 0x15Interrupts: 1453 (2
[code]....
View 3 Replies
View Related
May 15, 2012
I notice strange input rates on the interfaces of a 881 router:
show int fa4
..
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec
..
30 second input rate 85000 bits/sec, 11 packets/sec
30 second output rate 16000 bits/sec, 9 packets/sec
221434 packets input, 287889736 bytes
..
..
142286 packets output, 15683576 bytes, 0 underrun
How can 11 packets/sec be 85000 bits/sec -- average packet size of 8KB?. The total packets input (221434 packets versus 287+ MB) also shows this kind of a 10KB+ average packet size. There is ahardly any traffic through the router when the above snapshot was taken so 11 packets/sec sounds right, but not the 85Kbits/sec.
The router is running c880data-universalk9-mz.151-4.M4.bin and config is simple with a single Vlan (inside NAT) with a public IPs on fa4 and a couple of IPs for dynamic NAT. Everything works fine except for these interface counters that look worng.
View 1 Replies
View Related
Apr 15, 2013
I can't accsess web-interface on SF-300-24. My computer is on the same subnet. Can only access by RS232. The Switch doesn't answer on ping either. In the manual it says the switch has ip-adress 192.168.1.254.
View 4 Replies
View Related
Jan 18, 2012
There is some way to increase the speed of changing the interface state from DOWN to UP when the cable is connected. I need to configure a port of Cisco 4503 in a way that when a cable is connected the port goes immediatly UP.
A solution can be to keep Cisco interface always UP and I remember that with "no keepalive" command to the interface configuration it was possible. But I tried and nothing happens.
View 12 Replies
View Related
Nov 17, 2011
How to confirm if a 10Ge interface can be set down to 1Ge if required ?
View 4 Replies
View Related
May 24, 2012
Got a shiny new SG 200 26P which seems to work fine operationally.owever, when I am trying to access the web interface from a different IP subnet, the web brower just times out.If I put my PC on the same IP subnet, it works just fine. From the other subnet, I can ping the switch fine. The default gateway is set on the switch, and from the web interface I can ping and dns resolve other hosts and on the internet. I've tried to create a management profile to 'allow all from everywhere' basically, but still no luck.I'm completely stumped. I've tried to reset to firmware defaults, and I'm now runinng the latest firmware. I woudl suppose that the switch would allow itself to be managed via the web interface from all subnets by default. Any thoughts? The fact that the switch can ping internet hosts makes be believe it's own default gateway and IP are all ok and working.. (and I can ping it from anywhere in my network).
View 4 Replies
View Related
Oct 2, 2012
I have a CISCO2921. I am not able to bring up its gi0/1 interface. It stays down down.
[URL]
I know that interface is not coming up because of "no media" below. Router#sh int gi0/1 | i media Auto Duplex, Auto Speed, media type is no media
I have tried media rj-45 and media sfp which have also not worked. The other end of this link is ethernet handoff. What is it that I have to do for the link to come up? If I change the connection to gi0/2, I think that will work because I see this for gi0/2:
Router#sh int gi0/2 | i media Auto Duplex, Auto Speed, media type is RJ45
View 10 Replies
View Related
Nov 20, 2012
I need to set up a L2 llink between my LAN and this 1921 router. I though IRB would do it but its not working yet. Here is the topology- I dont want to see another hop on this 1921 rtr so I hope I can just trunk it or something with IRB. Not working.
View 6 Replies
View Related
Dec 28, 2010
I'm a networking newbie, but I bought the SG 200-08 switch to do Link Aggregation with and I can't access the web interface. I'm on a mac running 10.7.3, and I've tried Firefox and Safari. I've also tried on a friends PC with Internet Explorer 8.On the mac, I can go into the terminal and can see that the switch has the correct IP address and is seen on both ethernet ports.
View 2 Replies
View Related
Jan 11, 2013
how do we configure sub interface for nexus 7k?do we have to issue ma-address command under physical interface and than configure subinterface? if yes than what do we have to type the mac address for "mac-address" command?I can doing and than configure subinterface but the interface/subinterface didn't come up. do we have to bounce it couple times to bringe it up?
View 1 Replies
View Related
Apr 19, 2012
I am configuring my first 2911 using a SFP card but I dont know the interface name for this module.
show inv shows the card..
What is the interface number for this card or if it needs some config before it will recognize the interface?
View 6 Replies
View Related
Feb 24, 2013
I have encounterd a broplem on my Cisco 805 model.
When i use the command "show ip interface brief" the status shows "up" but the protocol is "down" on my serial interface.
The link between my to sites is down after this happend.
View 1 Replies
View Related
Jan 3, 2013
we've to configure our router 1841 to use both 2 interface Fe for two different vlan (also the second has to go on internet).
Actually we have int Fe0/0 configured with an ip address 192.168.1.1 for lan1 192.168.1.0/24 and we will use the second int Fe0/1 with another ip address like 192.168.2.1 for lan2 192.168.2.0/24.
see below configuration:
[code]...
View 5 Replies
View Related
Jul 19, 2012
I am in the process of staging a couple of two new Cisco ASR 1004's which are located at two locations with a WAN link in between. I need to set up connectivity between servers plugged directly into each ASR router across the WAN link. The ASR has 16 gig interfaces (gi0/0/0 - gi0/0/7 and gi0/1/0 - gi 0/1/7), and a management interface (gi0). I have connected the WAN link to gi0/0/0 and put an ip address on it. The servers will be plugged into the remaining gig interfaces. I tried to create an SVI (vlan interface) in an attempt to create an L3 interface to support routing to these servers but these routers don't allow SVI's to be created. how to put these server connected ports on a vlan and to create an L3 interface to provide routing to them?
View 1 Replies
View Related
Dec 3, 2012
I'm a networking newbie, but I bought the SG 200-08 switch to do Link Aggregation with and I can't access the web interface. I'm on a mac running 10.7.3, and I've tried Firefox and Safari. I've also tried on a friends PC with Internet Explorer 8.
On the mac, I can go into the terminal and can see that the switch has the correct IP address and is seen on both ethernet ports:
? (192.168.1.254) at 2c:36:f8:4f:fc:8 on en0 ifscope [ethernet]
? (192.168.1.254) at 2c:36:f8:4f:fc:8 on en1 ifscope [ethernet]
either accessing the web interface or with setting up the Link Aggregation on the switch some other way.
View 4 Replies
View Related
Jun 27, 2010
I just receive a new Cisco 3925 with a etherswitch module 24 port :
SM-ES3G-24-P,I successfully boot the switch module and gain access to it.
I found some documentation on CCO but I don't sorted out this small information :,
Switch#sh cdp neig Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone, D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port IDRouter Gig 0/26 143 R S I CISCO3925 Gig 2/0Switch#
The Router is connected to the switch module via a HIMI :
The Cisco enhanced EtherSwitch service modules also provide a physical Gigabit Ethernet serializer/deserializer integrated circuit transceiver (HIMI) interface. In the Cisco 2900 series and Cisco 3900 series routers, the HIMI link on the Cisco enhanced EtherSwitch service modules is connected to the router internal Gigabit Ethernet backplane. This link is used for interconnection between other interface cards or network modules attached to the router Gigabit Ethernet backplane bypassing the router host CPU; thus, increasing CPU performance by decreasing CPU processing.
If I do a sh ip int brief on the switch, I have 26 interface but only 24 are physicaly present on the front.The type of the 0/25 and 0/26 are the same : media type is 1000BaseXThe interface gi 0/26 is up up but the 0/25 is down down.
View 3 Replies
View Related
Sep 13, 2012
I have Comcast as my ISP and their Small Business Gateway Router/Firewall. I purchased a WRVS4400N and configured them like this:
Comcast Router/Firewall - 10.1.10.1
Cisco WRVS4400N - 10.1.11.1
I turned DHCP off on the Cisco so that wireless devices that connect to it get a 10.1.10 address from the Comcast device. Now, I am completely unable to connect to the web interface of the Cisco, whether connected to it wirelessly or even if I plug directly into one of the LAN ports on it. I have one of the LAN ports on the Cisco connected to one of the LAN ports on the Comcast. What am I missing here? I'm guessing I'm not able to see the 10.1.11 addresses when I am getting a 10.1.10 address from the Comcast, even though I'm connected to the Cisco?
View 6 Replies
View Related
