Cisco Switching/Routing :: Interface Counters On 881
May 15, 2012
I notice strange input rates on the interfaces of a 881 router:
show int fa4
..
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec
..
30 second input rate 85000 bits/sec, 11 packets/sec
30 second output rate 16000 bits/sec, 9 packets/sec
221434 packets input, 287889736 bytes
..
..
142286 packets output, 15683576 bytes, 0 underrun
How can 11 packets/sec be 85000 bits/sec -- average packet size of 8KB?. The total packets input (221434 packets versus 287+ MB) also shows this kind of a 10KB+ average packet size. There is ahardly any traffic through the router when the above snapshot was taken so 11 packets/sec sounds right, but not the 85Kbits/sec.
The router is running c880data-universalk9-mz.151-4.M4.bin and config is simple with a single Vlan (inside NAT) with a public IPs on fa4 and a couple of IPs for dynamic NAT. Everything works fine except for these interface counters that look worng.
View 1 Replies
ADVERTISEMENT
Dec 9, 2012
vlan interface and physical interface (that is serving for this vlan ) have different input/output counters, there is only one physical interface in this vlan .
sh int vlan 64
30 second input rate 9000 bits/sec, 9 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
[Code]....
View 5 Replies
View Related
Mar 19, 2012
We're running a simple policy map on a 3750 stack (IOS version 12.2(53)SE2), but the route-map counters do not show any matches:
NYKIRDRCX01#sh route-map
route-map remote-route, permit, sequence 51
Match clauses:
ip address (access-lists): remoteACL
Set clauses:
ip next-hop 192.168.101.5
Policy routing matches: 0 packets, 0 bytes
However, I've confirmed via our netflow monitor that the traffic we're trying to send to the appropriate next hop is, indeed, getting there correctly.
I've seen issues in the past with a 3750 not reporting counters correctly.
View 2 Replies
View Related
Feb 10, 2013
We have recently deployed several Ciso 887VAW (IOS 15.1(4)M4) to customer premises and I have come to realise counters show extremely high (not at all accurate) output rate and packets on all of them. [code]
View 2 Replies
View Related
Oct 16, 2012
This is a continuation of my last post in which I need to apply ACLs to the physical ports within Etherchannels. The switch is a Catalyst 2970 running IOS 12.2. These Etherchannels are configured as trunks with 2 VLANS allowed on each trunk.I have applied an inbound ACL on the physical ports that filters based on layer 3 and layer 4 traffic. The issue that I am seeing is that the counters for the ACL are not increasing even though the ACL is clearly doing its job. At the end of the ACL I have an entry of "permit ip any any". Removing this from the list causes connectivity problems to the server on this port. Adding it back and everything is back to normal. However the counters don't increase. At first I thought maybe this wasn't supported on this switch but then I noticed the counter had increased to "2 matches" later in the day. What is the normal behavior is for this switch and does it support logging on an ACL entry as well.
View 2 Replies
View Related
Dec 5, 2012
Ive got a 494810ge switch, and this parameters are important for me:
sh int gi 1/4 counters detail
Port InBytes InUcastPkts InMcastPkts InBcastPkts
Gi1/4 252819467437788 173264735013 10827 760
Port OutBytes OutUcastPkts OutMcastPkts OutBcastPkts
Gi1/4 36657317030233 280590958051 5248439 5443194
Port InPkts 64 OutPkts 64 InPkts 65-127 OutPkts 65-127
Gi1/4 558420918 205564441592 2627477631 60865368994
[code]....
Some parameters i can get by snmp (InBytes,InUcastPkts,InMcastPkts, and so on from out), but how can i take other parameters? I would like to do it by snmp but i did not find proper oids. Now I making a sheme like this: eem every 90 seconds takes this info and writes it down to file into nvram and then send it by scp to server, where file is processed by monitoring system script. It is not very good, cause cisco system cpu sometimes spikes of this and i dont know a resourse of nvram, how much times can i write to it?
View 2 Replies
View Related
Oct 28, 2012
how I can check the qos counters and stats for interfaces on my cat 6509 ?
View 1 Replies
View Related
Sep 7, 2012
I am attempting to monitor bandwidth utilization of the WAN port for the RV180 via SNMP and I am getting strange results. If a 256MB file is transferred from a remote server (without compression), the ifInOctets counter doesn't increment by anything resembling 256MB:
$ snmpget -v2c -c public 192.168.1.1 IF-MIB::ifInOctets.5 IF-MIB::ifOutOctets.5
IF-MIB::ifInOctets.5 = Counter32: 365402138
IF-MIB::ifOutOctets.5 = Counter32: 32610053
[Code].....
I'm reasonably certain that the .5 interface is the WAN port based on the value of ipAdEntIfIndex.X.X.X.X, but even if that were not the case, none of the other interfaces increment by a value close to the amount of data transfered. SNMP monitoring of a WAP121 on the same subnet returns expected results. I can only assume that SNMP on the RV180 is completely broken.
The router has the latest firmware available (1.0.1.9). There is only one network connection and the RV180 is the default gateway for all internal hosts.
View 4 Replies
View Related
Jun 12, 2012
Any chance of one or preferably both of these before I flash the router to a more competent firmware?Rather ridiculous that there's no interface counters and no SNMP server. I prefer keeping stock firmware where possible but I need this functionality, it really isn't a big ask.That said I have an E4200 v1, which already looks like abandonware given it's been 6 months since the last firmware update - not amused and no intention of swapping a high performance router for one that sacrifices performance for better NAS functionality.
View 8 Replies
View Related
May 23, 2011
I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
View 3 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
Mar 12, 2013
Quick question here. Using 3750E series switches with multiple VLANS configured. These switches serve as our 'core'. I have SVIs configured for the different VLANs and add inbound ACLs in each of the SVIs to control traffic between VLANS. This switch also terminates a P2P Ethernet link which connects to our Colo facility. The port used for this is configured as an L3 port. I noticed today that I was able to send traffic across this L3 link that I thought should have been blocked by an ACL I had in place but it wasn't. So the traffic flowed from a port in say VLAN 20 across this L3 link (assigned with an IP address). Would this traffic flow not cause traffic to be checked against an ACL applied in the inbound direction on the SVI of VLAN 20 (int vlan 20)? Traffic does get checked when routing between SVIs. Why would it not get checked when routing between SVI and L3 interface?
View 2 Replies
View Related
Mar 7, 2012
On a pair of my CISCO7609-s (engine:sup720-3B IOS Version:12.2(33)SRD4),some interfaces is configured as routing interface but also them are attend MSTP caculation and i really caught BPDU packet go out from these ports. [code]
View 1 Replies
View Related
Feb 26, 2013
We got a layer3 switched network, with one vlan for every switch, routed by a cat4006. [code] So can we put some ports on different switches in, let`s say vlan 50, with different ips? For example, Port 0/3 on Switch 1 and 0/8 on Switch 2, but keeping the ip of the "old" vlan? Or is it necessary to configure a specified vlan interface with ip-adress for every vlan if i want to route it?
View 4 Replies
View Related
Jan 7, 2012
I am a recent student to Cisco products and I have purchased some (what I thought was good) lab equipment to learn with on a budget. What I have is a 2948G switch and a 2620 router. My issue is this: the router has only one fast Ethernet port. Is it possible to use V LAN's and V LAN Interfaces on the router and switch to somehow emulate a second interface to connect to a WAN or sub net?
View 11 Replies
View Related
Aug 30, 2010
i've got a Cisco 877 router connected to an ADSL link. i'm using the show dsl interface atm just to have a look on its performance. i've tried to search on Cisco website on how to interpret the output but a blog gave me more info [URL]. My question now is, what readings do i consider? is it on the left (ATU-R) or on the right (ATU-C)?
877ROUTER#sh dsl int atm0 ATU-R (DS) ATU-C (US)Modem Status: Showtime (DMTDSL_SHOWTIME)DSL Mode: ITU G.992.1 (G.DMT)ITU STD NUM: 0x01 0x01Vendor ID: 'ALCB' 'ALCB'Vendor Specific: 0x0000 0x0000Vendor Country: 0x00 0x0FCapacity Used: 31% 85%Noise Margin: 34.0 dB 10.0 dBOutput Power: 16.0 dBm 12.0 dBmAttenuation: 10.0 dB 6.0 dBDefect Status: None None Last Fail Code: NoneSelftest Result: 0x00Subfunction: 0x15Interrupts: 1453 (2
[code]....
View 3 Replies
View Related
Apr 15, 2013
I can't accsess web-interface on SF-300-24. My computer is on the same subnet. Can only access by RS232. The Switch doesn't answer on ping either. In the manual it says the switch has ip-adress 192.168.1.254.
View 4 Replies
View Related
Jan 18, 2012
There is some way to increase the speed of changing the interface state from DOWN to UP when the cable is connected. I need to configure a port of Cisco 4503 in a way that when a cable is connected the port goes immediatly UP.
A solution can be to keep Cisco interface always UP and I remember that with "no keepalive" command to the interface configuration it was possible. But I tried and nothing happens.
View 12 Replies
View Related
Nov 17, 2011
How to confirm if a 10Ge interface can be set down to 1Ge if required ?
View 4 Replies
View Related
Aug 31, 2012
I have a switch WS-C4507R + E, added two SFP SFP-10GBase-SR, and they stayed with inactive status, activate these interfaces in 10Gb.
SWC-DC01#sh interfaces status module 4
Port Name Status Vlan Duplex Speed Type
Te4/1 connected trunk full a-1000 1000BaseBX10-U
Te4/2 notconnect 1 full auto No XCVR
Te4/3 inactive 220 full auto 10GBase-SR
Te4/4 inactive 220 full auto 10GBase-SR
[code]......
View 1 Replies
View Related
May 24, 2012
Got a shiny new SG 200 26P which seems to work fine operationally.owever, when I am trying to access the web interface from a different IP subnet, the web brower just times out.If I put my PC on the same IP subnet, it works just fine. From the other subnet, I can ping the switch fine. The default gateway is set on the switch, and from the web interface I can ping and dns resolve other hosts and on the internet. I've tried to create a management profile to 'allow all from everywhere' basically, but still no luck.I'm completely stumped. I've tried to reset to firmware defaults, and I'm now runinng the latest firmware. I woudl suppose that the switch would allow itself to be managed via the web interface from all subnets by default. Any thoughts? The fact that the switch can ping internet hosts makes be believe it's own default gateway and IP are all ok and working.. (and I can ping it from anywhere in my network).
View 4 Replies
View Related
Oct 2, 2012
I have a CISCO2921. I am not able to bring up its gi0/1 interface. It stays down down.
[URL]
I know that interface is not coming up because of "no media" below. Router#sh int gi0/1 | i media Auto Duplex, Auto Speed, media type is no media
I have tried media rj-45 and media sfp which have also not worked. The other end of this link is ethernet handoff. What is it that I have to do for the link to come up? If I change the connection to gi0/2, I think that will work because I see this for gi0/2:
Router#sh int gi0/2 | i media Auto Duplex, Auto Speed, media type is RJ45
View 10 Replies
View Related
Nov 20, 2012
I need to set up a L2 llink between my LAN and this 1921 router. I though IRB would do it but its not working yet. Here is the topology- I dont want to see another hop on this 1921 rtr so I hope I can just trunk it or something with IRB. Not working.
View 6 Replies
View Related
Dec 28, 2010
I'm a networking newbie, but I bought the SG 200-08 switch to do Link Aggregation with and I can't access the web interface. I'm on a mac running 10.7.3, and I've tried Firefox and Safari. I've also tried on a friends PC with Internet Explorer 8.On the mac, I can go into the terminal and can see that the switch has the correct IP address and is seen on both ethernet ports.
View 2 Replies
View Related
Jan 11, 2013
how do we configure sub interface for nexus 7k?do we have to issue ma-address command under physical interface and than configure subinterface? if yes than what do we have to type the mac address for "mac-address" command?I can doing and than configure subinterface but the interface/subinterface didn't come up. do we have to bounce it couple times to bringe it up?
View 1 Replies
View Related
Apr 19, 2012
I am configuring my first 2911 using a SFP card but I dont know the interface name for this module.
show inv shows the card..
What is the interface number for this card or if it needs some config before it will recognize the interface?
View 6 Replies
View Related
Feb 24, 2013
I have encounterd a broplem on my Cisco 805 model.
When i use the command "show ip interface brief" the status shows "up" but the protocol is "down" on my serial interface.
The link between my to sites is down after this happend.
View 1 Replies
View Related
Jan 3, 2013
we've to configure our router 1841 to use both 2 interface Fe for two different vlan (also the second has to go on internet).
Actually we have int Fe0/0 configured with an ip address 192.168.1.1 for lan1 192.168.1.0/24 and we will use the second int Fe0/1 with another ip address like 192.168.2.1 for lan2 192.168.2.0/24.
see below configuration:
[code]...
View 5 Replies
View Related
Jul 19, 2012
I am in the process of staging a couple of two new Cisco ASR 1004's which are located at two locations with a WAN link in between. I need to set up connectivity between servers plugged directly into each ASR router across the WAN link. The ASR has 16 gig interfaces (gi0/0/0 - gi0/0/7 and gi0/1/0 - gi 0/1/7), and a management interface (gi0). I have connected the WAN link to gi0/0/0 and put an ip address on it. The servers will be plugged into the remaining gig interfaces. I tried to create an SVI (vlan interface) in an attempt to create an L3 interface to support routing to these servers but these routers don't allow SVI's to be created. how to put these server connected ports on a vlan and to create an L3 interface to provide routing to them?
View 1 Replies
View Related
Dec 3, 2012
I'm a networking newbie, but I bought the SG 200-08 switch to do Link Aggregation with and I can't access the web interface. I'm on a mac running 10.7.3, and I've tried Firefox and Safari. I've also tried on a friends PC with Internet Explorer 8.
On the mac, I can go into the terminal and can see that the switch has the correct IP address and is seen on both ethernet ports:
? (192.168.1.254) at 2c:36:f8:4f:fc:8 on en0 ifscope [ethernet]
? (192.168.1.254) at 2c:36:f8:4f:fc:8 on en1 ifscope [ethernet]
either accessing the web interface or with setting up the Link Aggregation on the switch some other way.
View 4 Replies
View Related
Jun 27, 2010
I just receive a new Cisco 3925 with a etherswitch module 24 port :
SM-ES3G-24-P,I successfully boot the switch module and gain access to it.
I found some documentation on CCO but I don't sorted out this small information :,
Switch#sh cdp neig Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone, D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port IDRouter Gig 0/26 143 R S I CISCO3925 Gig 2/0Switch#
The Router is connected to the switch module via a HIMI :
The Cisco enhanced EtherSwitch service modules also provide a physical Gigabit Ethernet serializer/deserializer integrated circuit transceiver (HIMI) interface. In the Cisco 2900 series and Cisco 3900 series routers, the HIMI link on the Cisco enhanced EtherSwitch service modules is connected to the router internal Gigabit Ethernet backplane. This link is used for interconnection between other interface cards or network modules attached to the router Gigabit Ethernet backplane bypassing the router host CPU; thus, increasing CPU performance by decreasing CPU processing.
If I do a sh ip int brief on the switch, I have 26 interface but only 24 are physicaly present on the front.The type of the 0/25 and 0/26 are the same : media type is 1000BaseXThe interface gi 0/26 is up up but the 0/25 is down down.
View 3 Replies
View Related
Sep 13, 2012
I have Comcast as my ISP and their Small Business Gateway Router/Firewall. I purchased a WRVS4400N and configured them like this:
Comcast Router/Firewall - 10.1.10.1
Cisco WRVS4400N - 10.1.11.1
I turned DHCP off on the Cisco so that wireless devices that connect to it get a 10.1.10 address from the Comcast device. Now, I am completely unable to connect to the web interface of the Cisco, whether connected to it wirelessly or even if I plug directly into one of the LAN ports on it. I have one of the LAN ports on the Cisco connected to one of the LAN ports on the Comcast. What am I missing here? I'm guessing I'm not able to see the 10.1.11 addresses when I am getting a 10.1.10 address from the Comcast, even though I'm connected to the Cisco?
View 6 Replies
View Related
Apr 4, 2013
I am using cisco packet tracer to configure the hsrp on 3560 (c3560-advipservicesk9-mz.122-37.SE1.bin) but the standby ip Command is not available on the interface the problem in that IOS or in config
View 1 Replies
View Related
