I am attempting to monitor bandwidth utilization of the WAN port for the RV180 via SNMP and I am getting strange results. If a 256MB file is transferred from a remote server (without compression), the ifInOctets counter doesn't increment by anything resembling 256MB:
I'm reasonably certain that the .5 interface is the WAN port based on the value of ipAdEntIfIndex.X.X.X.X, but even if that were not the case, none of the other interfaces increment by a value close to the amount of data transfered. SNMP monitoring of a WAP121 on the same subnet returns expected results. I can only assume that SNMP on the RV180 is completely broken.
The router has the latest firmware available (1.0.1.9). There is only one network connection and the RV180 is the default gateway for all internal hosts.
Any chance of one or preferably both of these before I flash the router to a more competent firmware?Rather ridiculous that there's no interface counters and no SNMP server. I prefer keeping stock firmware where possible but I need this functionality, it really isn't a big ask.That said I have an E4200 v1, which already looks like abandonware given it's been 6 months since the last firmware update - not amused and no intention of swapping a high performance router for one that sacrifices performance for better NAS functionality.
I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
Ive got a 494810ge switch, and this parameters are important for me:
sh int gi 1/4 counters detail Port InBytes InUcastPkts InMcastPkts InBcastPkts Gi1/4 252819467437788 173264735013 10827 760 Port OutBytes OutUcastPkts OutMcastPkts OutBcastPkts Gi1/4 36657317030233 280590958051 5248439 5443194 Port InPkts 64 OutPkts 64 InPkts 65-127 OutPkts 65-127 Gi1/4 558420918 205564441592 2627477631 60865368994
[code]....
Some parameters i can get by snmp (InBytes,InUcastPkts,InMcastPkts, and so on from out), but how can i take other parameters? I would like to do it by snmp but i did not find proper oids. Now I making a sheme like this: eem every 90 seconds takes this info and writes it down to file into nvram and then send it by scp to server, where file is processed by monitoring system script. It is not very good, cause cisco system cpu sometimes spikes of this and i dont know a resourse of nvram, how much times can i write to it?
I've got an SG300-10 connected back to back (trunked) with a Cisco 3560X switch, across a fibre link and am seeing some big inconsistencies in terms of unicast data transferred across the ports between them.
During a night time window of 4am - 6am I run backups which involves a large copy of files, that almost saturates a GigE link - we can see from the 3560X end that the link is running at a bit over 800MBit/sec of throughput, sustained. The duration of this transfer is consistent with the size of the files being transferred (ie just over an hour, and is what I'd expect for a data transfer of about that amount). Back-of-the-envelope calculations indicate that the 3560X is measuring this data throughput correctly.
However on the SG300 end of the link, which is also being polled by the same application (Cacti), I'm observing spikey counts of only around 20MBit/sec during that window. These counters are very obviously incorrect - there's a huge amount more data moving across the port than that. The incorrect calculations are showing on both the trunk port out of the SG300 (uplink) as well as the interface where the NAS is connected in (which is an access port).
Cacti is polling the OID: .1.3.6.1.2.1.2.2.1.16.57 which translates to IF-MIB::ifOutOctets.57 = Counter32.I'm running version 1.3.0.62 but this problem is not new to this release - previous releases and 1.2 based releases also had this problem.
It looks like multicast traffic may be being counted correctly (that's only a suspicion though), however what I am certain of is that there is a very large discrepancy with the unicast traffic counts.Is this OID the correct one to be using for this switch?
which models of HP ProCurve or Dell PowerConnect support 64-bit IF-MIB counters, or for that matter any other manufacturer (Zyxel?) (snmpv2 or v3, OID .1.3.6.1.2.1.31.1.1.1.6)I believe pretty much any Cisco Catalyst above a 2950 do, however don't believe any of the SG series do. I realize I could pick up a 2960G for $1500-2k and be good to go, but I forsee a larger switch purchase in the future, but still could use a switch in the meantime that was able to allow accurate monitoring of closet uplink bandwidth?
We have recently deployed several Ciso 887VAW (IOS 15.1(4)M4) to customer premises and I have come to realise counters show extremely high (not at all accurate) output rate and packets on all of them. [code]
I notice strange input rates on the interfaces of a 881 router:
show int fa4 .. MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec .. 30 second input rate 85000 bits/sec, 11 packets/sec 30 second output rate 16000 bits/sec, 9 packets/sec 221434 packets input, 287889736 bytes .. .. 142286 packets output, 15683576 bytes, 0 underrun
How can 11 packets/sec be 85000 bits/sec -- average packet size of 8KB?. The total packets input (221434 packets versus 287+ MB) also shows this kind of a 10KB+ average packet size. There is ahardly any traffic through the router when the above snapshot was taken so 11 packets/sec sounds right, but not the 85Kbits/sec.
The router is running c880data-universalk9-mz.151-4.M4.bin and config is simple with a single Vlan (inside NAT) with a public IPs on fa4 and a couple of IPs for dynamic NAT. Everything works fine except for these interface counters that look worng.
vlan interface and physical interface (that is serving for this vlan ) have different input/output counters, there is only one physical interface in this vlan .
sh int vlan 64 30 second input rate 9000 bits/sec, 9 packets/sec 30 second output rate 0 bits/sec, 0 packets/sec
In the Ciscoview, the uplink SFP interfaces of 2960S stack are represented incorrectly. The two uplink interface should be Ten1/0/1 and Ten4/0/1 but proved to be Ten1/0/1 and Gi4/0/25. There is no 1G SFP module, so that the interface gi4/0/25 doesn't exist. [code]
I am seeing Interface output drops that appera to be incorrect. When I do "Show Interface gi1/0/20", I will get interface output drops of "4294961382". But, when I do the same command again it shows "0" drops. Is this a reporting error? I am ruinning c3750-ipservicesk9-mz.122-58.SE.bin on a 3750 stack with 2 switches in the stack. [code]
i am new to MPLS on cisco routers. For our interoperability testing i need MPLS tunnel counters output ( data sent out and data received.). i am not able to find this information in cisco user guide. As per standard it is defined in MIB table mplsTunnelPerfTable of stdte.mib.
I am getting these unwanted entries on my syslog server.03/10/2012 12:57:48 172.21.113.20 Error 23898: Interface FastEthernet0/1, changed state to downI tried to stop them with no snmp trap link-status but it hasn;t worked.[CODE]
I'm familiar with snmp-server views and excluding certain mib's, but is it possible to permit an snmp host to poll just one interface and nothing else on the router?
I have a cisco 1841, Im trying to write an app which will get the Interface Utilization on my 2 atm interfaces and fast eth 0/0 interface.
I’ve been reading up and have got as far as downloading the codeplex snmp library project. I’m using the snmpget app to get details off my 1841 successfully, but I now need to know the OID for interface utilization and how to define which interface to get.
i have a Problem with SNMP on the ASA Outside Interface. I want to monitor the Interface via SNMP (linkup, link down). I have a Active/Passive Cluster running on 8.4.2 and configured SNMP (v1) for Test on the Outside Interface. It's not that hard but when i try to test my Configuration with (peerless) SNMP Tester the Interface doesn't respond. Did i forget to configure something? Searched the forum but didn't find anything useful.
MIB OID and the values.also i want to know the values og output packet and output packet drops MIB OID values of POS interface on GSR router (12000).because i am getting many output packet drops on these pos interface.how do i get these values from the router.
I'm trying to add some 2800 series routers to our monitoring environment, but I can't get them discovered.
On the Mgmt Server I need to go through a "discovery" process to add the 2800 to the system. For this I target the internal interface ( i) but the discovery fails. I'm assuming the packets are getting dropped on the outside interface (e). I know SNMP is set up correctly and works as I had PRTG installed on a local box (p) for testing purposes.
The intention is to do the data gathering via a proxy agent (p), so enableing SNMP on the outside interface is not going to do me any good.What do I need to do to let those discovery packets pass through? At least temporarily?
I have an RV180 VPN router.I try to enable the VPN users with PPTP or QuickVPN but is not working.For PPTP sometimes my windows 7 connects to the router, sometimes doesn't connect with a random error message.When it connects, the windows 7 from outside the lan can see the computers from inside the lan but the computers from inside the lan cannot see the windows7 one. This is random also. When i succed to connect, from that computer, the internet is not working anymore.I tried to set the VPN in the same subnet as lan, i tried with different subnet. Is not working.I updated the last firmware. The same.Restore factory settings couple of times, the same.
I noticed if you add more than 10 access rules to the Access Rule table, you are unable to reorder past the first 10.Steps to reproduce:Create 11 rules of the same stream direction, outbound or inbound (...I found the bug with outbound, did not test inbound).try to reorder one of the first 10 rules to the end of the list, either by entering "11" manually, or by pressing the down arrow.System responds that "11" is an invalid number, or that the rule cannot be moved.This issue is not reported in the "Known Issues" section of the release notes for 1.0.1.9.
Which vpn client to use on os x ? (the one included in os x or another?) Which VPN configuration to use on RV180 ? and Which ports to open on RV180 Firewall ? (or any other parameters)
In both cases above, after I started to suspect QOS, I entered a narrow IP range to test and then a MAC to test. Using a VLAN seems to work fine and generate no errors - even a VLAN for the same associated host(s).
I have a support case open about this - didn't get too far yet, but now with a better repro, maybe they will.
I currently have an RV180 in a small business set-up and curently being accessed remotely by laptops (Quick VPN) and Ipads/Android ICS tablets (PPTP). All is working well but I've become concerned about the security risks of PPTP and would like to shift the tablets to IPSec.
1) For a small business are the PPTP risks real?
2) What are the alternatives for Android ICS? I can't find a Quick VPN client for Android.
3) I can't get the core IPSec VPN in Android to connect to the RV180? Is this possible?
I have RV180 configured with two VLANs. First VLAN is untagged and second VLAN is tagged. The purpose is two have two subnets, with the second subnet used for guest access. Both VLANs have DHCP server enabled. First VLAN is 192.168.1.0/24 and the second VLAN is 192.168.2.0/24, When I connect a computer with untagged Ethernet interface, it gets an IP address from DHCP server on the first subnet i.e. 192.168.1.100 and it can successfully access Internet. When I connect a computer with tagged Ethernet interface (I am using VLAN ID 10), it gets an IP address from DHCP server on the second VLAN i.e. 192.168.2.100. So far so good. I can successfully ping hosts on the Internet i.e. ping www.google.com. But I cannot access Internet from the web browser. I captured Wireshark trace and here is what I see...
1. TCP SYN. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10) 2. TCP SYN ACK. Source IP A.B.C.D, destination IP 192.168.2.100. Ethernet frame has VLAN tag (VLAN ID 10) 3. TCP ACK. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10) 4. TCP Data. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10) 5. TCP Data. Source IP A.B.C.D, destination IP 192.168.2.100. Frame is untagged
The problem is at #5. Packet came back from the Web Server. RV180 properly NATed it to the local IP address. But it did not add VLAN tag.
I just recieved a new RV180 yesterday and it will not connect to my switch. Router was updated to the newest firmware, reset to factory settings. I did change the ip and ip range. Router works fine with one computer attached direct. As soon as I connect my sf300-24P to it, the WAN and LAN lights all light up and then go out. Only the WAN will light back up. I have no connectivity to the router. I plug the laptop to the router directly and no LAN lights come on and can not see the router with arp -a.
I'm considering upgrading a small business to the newly released RV180 or RV180W.Does the RV180 series support 6rd (IPv6 rapid deployment?).I see 6rd documented in the other small business routers (e.g. RV110), but I can't find it in the RV180 documentation.
I'm having issues getting QuickVPN to connect. I think it's an issue pinging the gateway but I'm not 100% sure. We are using Comcast Business, I have placed the RV180 in the DMZ. The setup looks like this: Internet -> Comcast router -> RV180 (DHCP) -> rest of network.
Is there a guide to setup a VPN connection using this router? I've follow the setup guide provided by cisco but I'm having issues. When attempting to connect using the quick vpn client, I get error messages.
Any news on a new firmware for the RV180? I have the most recent version but it still has lots of bugs. IPSec needs polishing. In addition the Logging functions don't work well. I can't send to a syslog and when I try to email the logs I get a email saying there is no data even though several pages of enteries are visible in the web GUI. I've checked the profiles and they are correct. I even tried using just the 'default' profile but no luck.
