I am getting these unwanted entries on my syslog server.03/10/2012 12:57:48 172.21.113.20 Error 23898: Interface FastEthernet0/1, changed state to downI tried to stop them with no snmp trap link-status but it hasn;t worked.[CODE]
View 4 RepliesI have a 3750 cluster and I want to know what are the recommended snmp traps to be sent. We definitely want to know when one of the switches in the cluster fails.
I've read about snmp-server enable traps stackwise and snmp-server enable traps cluster. What do these traps actually do?
I have been experiencing wireless connectivity issues with one of our Cisco 1231G AP. Every now and then users would not be able to connect to the AP. To dive deeper into this issue, I would like to configure SNMP traps on this AP. We are using PRTG and there is an option to configure SNMP trap. However, I would need to now the OID of the AP. Also i need to check for interface up/down status for both fastethernet and the radio. PRTG should be able to notify me when there is any interface resets.
View 6 Replies View RelatedI want to configure snmp-traps regarding stpx (root-inconsistency, loop-inconsistency) on a Cisco Nexus 1000V. The command "show snmp traps" lists stpx as a trap that could be configured and which is not at the moment.
MKBE1NX1# sh snmp trap
--------------------------------------------------------------------------------
Trap type Enabled
--------------------------------------------------------------------------------
entity : entity_mib_change Yes
entity : entity_module_status_change Yes
entity : entity_power_status_change Yes
[code].....
Nothing about stpx... Is there some other way to configure more traps?
Is there a way to send an SNMP trap form the ASA when port 80 is trying to be accessed??
We use the ASA5510 and also use ScanSafe Web Security. Web Security is great but we find ourselves worrying if user has edited their Browser connection settings to remove the proxy settings that we push down using Group Policy. We also cut off the users ability to make changes to those settings but it interferes when I need to troubleshoot a special program that cant use a proxy server. It just makes it harder for me. The other thing is that Group Policy only works for IE. Google Chrome will inherit the system settings in IE. So we have Safari and Firefox as well as a lot of others to worry about not getting the configuration. There is also debate about limitting the use of anything but IE and FireFox.
Without laying down the law and getting all sorts of hate mail and death threats I would like to run ScanSafe in such a way as to make sure each user receives the Group Policy settings and that is all.
I would now like to just set up an SNMP trap on the ASA for ANY traffic that is trying to get to port 80. Either get in in my syslog server or have the asa email me directly. Scansafe sends the Internet traffic out on 8080 to the Proxy towers.
I could block port 80 outbound but again, I limit my ability to troubleshoot on the fly. I would have to break this every time I need to troubleshoot.
Had setup my ACE ,to send traps to SNMP server .but dont see any logs on the SNMP server from ACE.
SNMP configuration on ACE
logging enable
logging buffered 6
logging host 10.12.40.12 udp/514
[code].....
Trying to migrate the config run on IOS 12.1 to 12.2 ?It seems there's no snmop traps isdn command support on 12.2.
where i can enable trap on ISDN over IOS 12.2 (33) sxj1 running on C6500 chassis?
I am seeing SNMP coldstart traps that either are delayed by many hours or are false (e.g. right after receiving the coldstart trap a query to sysUptime shows the nodes been up for days).I seen this twice this week in a new network environment for me for two different C2900s running C2900-UNIVERSALK9-M Version 15.0(1)M3 Assuming the coldstart traps are coming from the actual source nodes, I am curious what could be going on here.
1) One guess I have is possibly the system clock changed could cause the SNMP agent to send a false cold start trap. Then my guess is in the device log I should see a system time change syslog message.
2) I recall hearing once that syslog and possible traps messages are held in configurable buffer who default value is 1 and if not sent are held and then suffer a delayed sent. Is it true for both traps and syslog ? In the past I assumed this was simply the logging history buffer and applicable to syslog traps only. My assumption in the past was that last trap or last syslog message is sometimes held on reload and sent immediately after restart regardless of device connectivity to the management target.
I always assumed coldstart traps are never delayed for any reason and that they were pretty accurate substitutes for system reload syslog messages. Does anyknow know any reason for false or delayed coldstart traps on a C2900 with IOS 15.0(1) ?
Cisco LMS 4.0: Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address? • Traps contain the original Device Agent IP to identify the source (Not the IP of LMS)?• Is possible to configure one logical IP address or Domain Name for redundant LMS:Cisco Security Manager 4.1:Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address?• Traps contain the original Device Agent IP to identify the source (Not the IP of Security Manager)? • Is possible to configure one logical IP address or Domain Name for redundant Security Manager?
View 0 Replies View RelatedI want to capture RPS related alarm on SNMP server for RPS2300 and cisco 3750d switch
View 1 Replies View RelatedWe have a catalyst 2950 switch running:
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA6, RELEASE SOFTWARE (fc1)
This release doesnt have the snmp-server enable traps errdisable command.
Where to look on the cisco site for the next available release for me that would have this command in place?
Sometimes we have unidentified traps in our log, we don't know where they come from.
In high severity faults we see an active alert with device name “Unidentified” event name unresponsive but with a certain ip address.
What are these alerts about? Can I filter them?,A second issue I have is that I get interface down alerts. But when we log on to the device, there is no interface down at all. We can also ping the device from the lms server at that time. I have been told that the admin state and operational state has to be up.
I'm familiar with snmp-server views and excluding certain mib's, but is it possible to permit an snmp host to poll just one interface and nothing else on the router?
View 2 Replies View RelatedI have a cisco 1841, Im trying to write an app which will get the Interface Utilization on my 2 atm interfaces and fast eth 0/0 interface.
I’ve been reading up and have got as far as downloading the codeplex snmp library project. I’m using the snmpget app to get details off my 1841 successfully, but I now need to know the OID for interface utilization and how to define which interface to get.
i have a Problem with SNMP on the ASA Outside Interface. I want to monitor the Interface via SNMP (linkup, link down). I have a Active/Passive Cluster running on 8.4.2 and configured SNMP (v1) for Test on the Outside Interface. It's not that hard but when i try to test my Configuration with (peerless) SNMP Tester the Interface doesn't respond. Did i forget to configure something? Searched the forum but didn't find anything useful.
View 4 Replies View Relatedhow to enable snmp on SVI interface on cisco ME-3600X-24FS-M?I can't see traffic on SVI via snmp.
View 13 Replies View RelatedMIB OID and the values.also i want to know the values og output packet and output packet drops MIB OID values of POS interface on GSR router (12000).because i am getting many output packet drops on these pos interface.how do i get these values from the router.
View 1 Replies View RelatedI am attempting to monitor bandwidth utilization of the WAN port for the RV180 via SNMP and I am getting strange results. If a 256MB file is transferred from a remote server (without compression), the ifInOctets counter doesn't increment by anything resembling 256MB:
$ snmpget -v2c -c public 192.168.1.1 IF-MIB::ifInOctets.5 IF-MIB::ifOutOctets.5
IF-MIB::ifInOctets.5 = Counter32: 365402138
IF-MIB::ifOutOctets.5 = Counter32: 32610053
[Code].....
I'm reasonably certain that the .5 interface is the WAN port based on the value of ipAdEntIfIndex.X.X.X.X, but even if that were not the case, none of the other interfaces increment by a value close to the amount of data transfered. SNMP monitoring of a WAP121 on the same subnet returns expected results. I can only assume that SNMP on the RV180 is completely broken.
The router has the latest firmware available (1.0.1.9). There is only one network connection and the RV180 is the default gateway for all internal hosts.
I'm trying to add some 2800 series routers to our monitoring environment, but I can't get them discovered.
On the Mgmt Server I need to go through a "discovery" process to add the 2800 to the system. For this I target the internal interface ( i) but the discovery fails. I'm assuming the packets are getting dropped on the outside interface (e). I know SNMP is set up correctly and works as I had PRTG installed on a local box (p) for testing purposes.
The intention is to do the data gathering via a proxy agent (p), so enableing SNMP on the outside interface is not going to do me any good.What do I need to do to let those discovery packets pass through? At least temporarily?
Any chance of one or preferably both of these before I flash the router to a more competent firmware?Rather ridiculous that there's no interface counters and no SNMP server. I prefer keeping stock firmware where possible but I need this functionality, it really isn't a big ask.That said I have an E4200 v1, which already looks like abandonware given it's been 6 months since the last firmware update - not amused and no intention of swapping a high performance router for one that sacrifices performance for better NAS functionality.
View 8 Replies View RelatedI have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
View 3 Replies View RelatedWe use Cacti to get interfaces statistics of a ASR1002 router (version 03.04.02.S.151-3.S2).A new GRE tunnel has been created, but unfortunately we are not able to get basic interface average during the day.What is surprising is the fact the graphs are built on the night only.
It seems as soon as we exceed some level of Bandwidth (~ 700-800k) the tool does not get the information.The OID I try to get are ifHCInOctets (.1.3.6.1.2.1.31.1.1.1.6) and ifHCOutOctets (.1.3.6.1.2.1.31.1.1.1.10) and some other interface statistics for both 64 and 32 bits. [code]
We have a vpn L2L with an ASA and C2900 and always stopping to ping each other but the vpn still UP and can each the others devices behind the peers.
Everytime we have to issue on router "clear cry isa peer" or on asa "clear ipsec peer" to start to ping each other but after seconds it's stopping to ping again.Is there something to fix it permanently? We did some debug crypto on asa but no information was logged.
I tried to update my ACS 5.1 appliance. I applied patch 5.1.0.44.3 and made an big mistake: I booted the server due to the fact that it was not reachable after one hour after appplying the patch. Now the server shows following message, when I try to apply other patches: Can not process requested software update operation since this ACS Instance currently has a software update inprogress.
My question: Is it possible to stop the upfate process and apply the other updates or is it possible to revert this update to go back to the previous patch level. For information: the appliance shows only the patches 5.1.0.44.1 and 5.1.44.0.2 installed.
I am having a huge problem since yesterday. I was using my wireless connection like always and it has randomly started to stop working for brief periods of time. It's like a continuous cycle where the internet works smoothly and fast (like always) for 30 secs at a time, then it goes into 15 secs where nothing works.
View 9 Replies View RelatedFirst, I'm running Windows7 64 bit. So whenever I download a decently sized file; my download will start and get good speed for a few minutes, then it will drop off and stop and my connection to the internet will be lost for a short time while the connection resets. This happens if I'm using a program like Steam to download a game, torrenting something, sometimes on my Xbox 360 when it needs to update itself or a game, occasionally on a large app or album off of iTunes or patching an online game. However, I have no issue watching YouTube videos or playing an online game while also having TeamSpeak running in the backround to chat. I don't lose connection when browsing the internet at all and recently I was able to stream a live event without issue but I only tried that once (I don't have Netflix or anything similar).It usally isn't a big issue because my download will pick up where it left off most of the time but its a pain in the butt to have to add on an extra hour to a download sometimes for this.
View 4 Replies View RelatedI haven't been able to get a decent answer to no matter how much googling etc I do. We have a problem in our flat where any time someone downloads something everyone else in the flat loses access to the internet until that person finishes their download or stops it. We are all accessing the internet through the same router, 3 of us wirelessly and 1 wired. The computers which are for some reason blocked by the other person downloading can't even access the router to do a reset or work out whats happening. [URL] gives our download speed as 14.80Mbps which isn't great but okay for good old NZ.Why would it be that 1 person downloading is preventing the others from accessing the net, do some downloads somehow take full control of all the available bandwidth ?.And is there any way to make it so that it doesn't happen, like make it so no computer can use all the bandwidth at a time ?, ie my flatmate can download his whatever but I can still send emails etc at the same time.
View 3 Replies View Relatedin LMS 4.0, is it possible to send traps from IPM? I remember that this was impossible from LMS 3.x.
View 1 Replies View RelatedI am working on LMS 3.2 . Tried to stop the daemon service with " net stop crmdmgtd ". It stuck on stopping state since few hours now. I can still open the application. How to terminate the previous command and restart the daemon service.
View 1 Replies View Relatedwe need config on WS-C3560G-24TS-S inter vlan communication stopping as per attached document.
View 1 Replies View RelatedI am experiencing strange problem about slowing down the internet speed after downloading is stopped in between. I then have reboot the desktop to regain the speed.
My networking as below:
DSL Modem
Dlink DIR-655 Router
Desktop A (Wired Network)
Desktop B (Wired Network)
Laptop (Wireless Network)
If I am downloading a file (1gb) on Desktop A and for some reason I have to stop it, then internet connection is desktop A , desktop B and laptop is almost killed. To get the speed back, I need to reboot Desktop A. All computers are on Windows 7.
If completely download the file, the internet speed is good on all the computers. Before downloading the speed is: After stopping the download the speed is :
I have a RV082 router that is currently in prod. I have a Dell Powerconnect 5424 switch that I'd like to use in place of the unmanaged switches I am currently using.I have the switch configured with it's IP, subnet, gateway, etc. I can plug devices into it and communicate with no problems. However, when I attempt to plug in the router, nothign will communicate to or from the switch. The devices I plugged in will not talk to each outer, ping the switch, or the router. Also cannot ping to the switch from a device plugged into the router. If I unplug the router, comm opens back up.
View 1 Replies View RelatedI have a RV082 router that is currently in prod. I have a Dell Powerconnect 5424 switch that I'd like to use in place of the unmanaged switches I am currently using.
I have the switch configured with it's IP, subnet, gateway, etc. I can plug devices into it and communicate with no problems. However, when I attempt to plug in the router, nothign will communicate to or from the switch. The devices I plugged in will not talk to each outer, ping the switch, or the router. Also cannot ping to the switch from a device plugged into the router. If I unplug the router, comm opens back up.