Cisco :: Traps From IPM In LMS 4.0?
Jul 11, 2011in LMS 4.0, is it possible to send traps from IPM? I remember that this was impossible from LMS 3.x.
View 1 Replies
ADVERTISEMENT
Cisco :: LMS 4.x How To Disable Certain Traps Being Displayed
Mar 16, 2012there are always some Traps more or less processed by LMS showing up in Fault Monitor View.Especially some Pass-Through or Unidentified Traps can be annoying if you want to keep the view clean.I wonder how to disable such Traps to not beeing displayd on the DFM Fault Monitor View?
View 1 Replies View RelatedCisco :: Can IPM LMS 4.1 Send Messages Or Traps
Dec 21, 2011We need IPM (LMS 4.1) to send and e-mail, sms o trap to NNM, is it possible??
View 2 Replies View RelatedCisco :: Stopping SNMP Traps For Interface Up / Down?
Oct 3, 2012I am getting these unwanted entries on my syslog server.03/10/2012 12:57:48 172.21.113.20 Error 23898: Interface FastEthernet0/1, changed state to downI tried to stop them with no snmp trap link-status but it hasn;t worked.[CODE]
View 4 Replies View RelatedCisco :: WLC 5508 Most Recent Traps Duplications
Mar 26, 2013I have recently noticed that in my WLC traps I keep finding lots of Mac addresses that have many hits on joining but it's the same MAC ADDRESS. Example Mac addresss'08:11:96:e4:1a:60,4Wed Mar 27 16:05:56 2013Client with MAC address 08:11:96:e4:1a:60 has joined profile corporate5Wed Mar 27 16:05:45 2013Client with MAC address 08:11:96:e4:1a:60 has joined profile corporate7Wed Mar 27 16:04:53 2013Client with MAC address 08:11:96:e4:1a:60 has joined profile corporate12Wed Mar 27 16:02:51 2013Client with MAC address 08:11:96:e4:1a:60 has joined profile corporate This has like 20 hits in the traps section and when I check my ISE this is also reflected on the authentication aspect. This is starting to occur with many different client laptops, why does it keep re-authenticatiing into the profile joined?Is there a Time to Live TTL setting I can set so it doesn't poll so often? The users aren't doing anything this is all occuring automcatically, I think it's the WLC 5508 controller not the ISE.
View 2 Replies View RelatedCisco :: 3750 Cluster And SNMP Traps?
Jun 15, 2011I have a 3750 cluster and I want to know what are the recommended snmp traps to be sent. We definitely want to know when one of the switches in the cluster fails.
I've read about snmp-server enable traps stackwise and snmp-server enable traps cluster. What do these traps actually do?
Cisco :: Configuring SNMP Traps On 1231G AP
Jan 17, 2011I have been experiencing wireless connectivity issues with one of our Cisco 1231G AP. Every now and then users would not be able to connect to the AP. To dive deeper into this issue, I would like to configure SNMP traps on this AP. We are using PRTG and there is an option to configure SNMP trap. However, I would need to now the OID of the AP. Also i need to check for interface up/down status for both fastethernet and the radio. PRTG should be able to notify me when there is any interface resets.
View 6 Replies View RelatedCisco :: 7.0.116.0 / WLC Generating Traps With Wrong SSID
Jul 5, 2011I've noted a number of traps reported correctly but with the wrong SSID in the detail on 7.0.116.0
View 1 Replies View RelatedCisco :: Unidentified Traps And Interface Down Alerts LMS 4.2
Feb 4, 2013Sometimes we have unidentified traps in our log, we don't know where they come from.
In high severity faults we see an active alert with device name “Unidentified” event name unresponsive but with a certain ip address.
What are these alerts about? Can I filter them?,A second issue I have is that I get interface down alerts. But when we log on to the device, there is no interface down at all. We can also ping the device from the lms server at that time. I have been told that the admin state and operational state has to be up.
Cisco :: Enable SNMP Traps On Nexus 1000V?
Dec 18, 2011I want to configure snmp-traps regarding stpx (root-inconsistency, loop-inconsistency) on a Cisco Nexus 1000V. The command "show snmp traps" lists stpx as a trap that could be configured and which is not at the moment.
MKBE1NX1# sh snmp trap
--------------------------------------------------------------------------------
Trap type Enabled
--------------------------------------------------------------------------------
entity : entity_mib_change Yes
entity : entity_module_status_change Yes
entity : entity_power_status_change Yes
[code].....
Nothing about stpx... Is there some other way to configure more traps?
Cisco :: Configure SNMP Traps For Port 80 On ASA 5510?
Jan 30, 2012Is there a way to send an SNMP trap form the ASA when port 80 is trying to be accessed??
We use the ASA5510 and also use ScanSafe Web Security. Web Security is great but we find ourselves worrying if user has edited their Browser connection settings to remove the proxy settings that we push down using Group Policy. We also cut off the users ability to make changes to those settings but it interferes when I need to troubleshoot a special program that cant use a proxy server. It just makes it harder for me. The other thing is that Group Policy only works for IE. Google Chrome will inherit the system settings in IE. So we have Safari and Firefox as well as a lot of others to worry about not getting the configuration. There is also debate about limitting the use of anything but IE and FireFox.
Without laying down the law and getting all sorts of hate mail and death threats I would like to run ScanSafe in such a way as to make sure each user receives the Group Policy settings and that is all.
I would now like to just set up an SNMP trap on the ASA for ANY traffic that is trying to get to port 80. Either get in in my syslog server or have the asa email me directly. Scansafe sends the Internet traffic out on 8080 to the Proxy towers.
I could block port 80 outbound but again, I limit my ability to troubleshoot on the fly. I would have to break this every time I need to troubleshoot.
Cisco WAN :: High CPU Utilization Is 2600 Due To Syslog Traps
Sep 21, 2011Iam facing an issue with high cpu utilization of cisco 2600 router . When i give show cpu process command i can see three process are using high cpu those are as below
Router #sh proc cpu sorted
CPU utilization for five seconds: 90%/3%; one minute: 92%; five minutes: 87%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
79 34734981 380093 91388 61.99% 60.36% 55.28% 0 Syslog Traps
70 3468095320 810529544 4278 14.41% 16.05% 16.15% 0 Encrypt Proc
32 2386134243 2409465973 0 6.79% 6.40% 6.57% 0 IP Input
What may be causing this issue.
Cisco Application :: SNMP Server Not Receiving Traps From ACE 4710
May 24, 2012Had setup my ACE ,to send traps to SNMP server .but dont see any logs on the SNMP server from ACE.
SNMP configuration on ACE
logging enable
logging buffered 6
logging host 10.12.40.12 udp/514
[code].....
Cisco Switching/Routing :: C6500 / SNMP-server Traps For ISDN?
May 17, 2012Trying to migrate the config run on IOS 12.1 to 12.2 ?It seems there's no snmop traps isdn command support on 12.2.
where i can enable trap on ISDN over IOS 12.2 (33) sxj1 running on C6500 chassis?
Cisco :: C2900 False And Delayed SNMP Cold Start Traps
May 31, 2012I am seeing SNMP coldstart traps that either are delayed by many hours or are false (e.g. right after receiving the coldstart trap a query to sysUptime shows the nodes been up for days).I seen this twice this week in a new network environment for me for two different C2900s running C2900-UNIVERSALK9-M Version 15.0(1)M3 Assuming the coldstart traps are coming from the actual source nodes, I am curious what could be going on here.
1) One guess I have is possibly the system clock changed could cause the SNMP agent to send a false cold start trap. Then my guess is in the device log I should see a system time change syslog message.
2) I recall hearing once that syslog and possible traps messages are held in configurable buffer who default value is 1 and if not sent are held and then suffer a delayed sent. Is it true for both traps and syslog ? In the past I assumed this was simply the logging history buffer and applicable to syslog traps only. My assumption in the past was that last trap or last syslog message is sometimes held on reload and sent immediately after restart regardless of device connectivity to the management target.
I always assumed coldstart traps are never delayed for any reason and that they were pretty accurate substitutes for system reload syslog messages. Does anyknow know any reason for false or delayed coldstart traps on a C2900 with IOS 15.0(1) ?
Cisco Switching/Routing :: LMS 4.0 Able To Forward SNMP Traps Received From Device Registered
Nov 16, 2011Cisco LMS 4.0: Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address? • Traps contain the original Device Agent IP to identify the source (Not the IP of LMS)?• Is possible to configure one logical IP address or Domain Name for redundant LMS:Cisco Security Manager 4.1:Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address?• Traps contain the original Device Agent IP to identify the source (Not the IP of Security Manager)? • Is possible to configure one logical IP address or Domain Name for redundant Security Manager?
View 0 Replies View RelatedCisco Switching/Routing :: Configure Snmp Traps For RPS 2300 Failure On 3750S?
Dec 7, 2011I want to capture RPS related alarm on SNMP server for RPS2300 and cisco 3750d switch
View 1 Replies View RelatedCisco Switching/Routing :: 3750 Switches Refuse To Fire The Port-security Violation Traps
Oct 20, 2010My group has recently started configuring traps on our switches to alert us of issues as they arise vs. waiting for the Helpdesk to receive user complaints and then responding.We have successfully configured the 2950 and 2960 switches to alert us when a port-security violation happens. However, the 3750 switches refuse to fire the port-security violation traps. The 3750's will fire an errdisable trap when the port goes down though.
Here is one of the port configurations:
interface FastEthernet1/0/45
switchport access vlan 5
switchport mode access
switchport port-security
switchport port-security mac-address sticky
[code].....
And here is the output of the port-security debug:
2522070: Oct 21 16:37:04: %LINK-3-UPDOWN: Interface FastEthernet1/0/45, changed state to down
2522089: Oct 21 16:37:05: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa1/0/45, putting Fa1/0/45 in err-disable state
2522100: Oct 21 16:37:05: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0012.3f07.95d3 on port FastEthernet1/0/45.
All of the 3750's are running C3750-IPBASEK9-M, Version 12.2(53) SE2. Wireshark also shows the errdisable traps, but no other traps so I've ruled out the traps being missed. All of the switches have been reloaded and power cycled.
Cisco Switching/Routing :: Catalyst 2950 - Release For Snmp-server Enable Traps Errdisable Command?
May 16, 2013We have a catalyst 2950 switch running:
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA6, RELEASE SOFTWARE (fc1)
This release doesnt have the snmp-server enable traps errdisable command.
Where to look on the cisco site for the next available release for me that would have this command in place?
Cisco Infrastructure :: 3550 Doesn't Send Traps When Bpdu-guard Sets A Port In Err-disable State
Mar 24, 2003Currently it seems as our 3550's doesn't send traps when bpdu-guard sets a port in err-disable state. Or DFM doesnt recognize it.Is there a way to get a DFM alert when a 3550-port gets into err-disable state?
View 2 Replies View RelatedCisco :: Test Fast Roaming Using A Cisco 2100 Series Controller And 2 1140 APs?
Jul 20, 2011I'm trying to test fast roaming using a Cisco 2100 Series controller and 2 1140 APs. The initial authentication succeeds fine and the wireless connection works ok using WPA2+CCKM and LEAP with a Cisco ACS radius server.The problem is that the client does not attempt to preauthenticate with the other AP because the RSN Capabilities IE in the AP beacons and probe responses do not set the RSN Preauthentication capable bit. I can't figure out what it takes to get the APs to indicate to clients that it can do preauthentication. I'm been crawling through all the documentation I can find, to no avail.
View 1 Replies View RelatedCisco WAN :: Does Cisco Catalyst 2960-8TC Support Bandwidth Limit Control
Aug 22, 2011We are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.
View 1 Replies View RelatedCisco Wireless :: WLAN Cisco / AP 3502e - How To Get PAT (Product Acceptance Test)
Dec 3, 2011I want to PAT my project of WLAN and i attached the document, how I create the Testing Criteria of the said scenarios, PAT document includes WCS 7.0, WLC 5508, MSE 3310, Cisco AP 3502e and ACS 4.2.
View 0 Replies View RelatedCisco Firewall :: Cisco ASA5510 Unable To Block Unwanted URLs
Jul 12, 2012I have cisco ASA5510 firewall using in my network but unable to bolck Url's unwanted. can i block the [URL] on the asa by using regular exp.
View 3 Replies View RelatedCisco Switching/Routing :: Configuring COS On 2960G Switches With Non-Cisco Phones
Mar 1, 2012I have 7 POE switches that have ESI IP phones attached. I have two VLANS, 1 and 2. VLAN 2 is used for voice and is defined in each switch.The ESI IP phones connect to my POE switch ports and the pc attaches through the ESI IP phone.
I have had voice quality issue between floors in my building. Talking to others on my floor via the IP phone, there are no voice quality issues. [code]
Cisco Wireless :: Connect Ap-1242AG With Non-cisco Router To Work As Repeater?
Nov 18, 2012is it possible to connect Cisco Ap-1242AG with non-cisco wireless router to work as repeater?
View 1 Replies View RelatedCisco :: Unable To Understand Cisco Syntax For Nat Rules On 5550
May 1, 2012I am looking at a config on a 5550 FW, and am trying to make sense of the syntax of the following rules. I have been to the Cisco site, but can't find much on the syntax.
View 8 Replies View RelatedCisco :: IPSec Tunnel Between Cisco ASA And OpenBSD (Access Enforcer)?
Mar 10, 2011I currently use a device called the Access Enforcer which runs OpenBSD. I have 3 stable, working VPN tunnel's where the other side's device is a Cisco ASA 5520 or 5540. I was setting up my 4th VPN where the other side used a Cisco ASA 5520 and ran into issue's. The Cisco side can bring up the tunnel. Once the tunnel is up each side can talk to the other side. However, when the tunnel is dropped, the OpenBSD side cannot bring up the tunnel. The error received is on the OpenBSD device is "isakmpd[29581]: transport_send_messages: giving up on exchange from-XX.X.X.0/24-to-XX.XXX.XXX.240, no response from peer XX.XX.XXX.141:4500". I have been trying to figure this out for weeks now and can't seem to find the cause.
View 3 Replies View RelatedCisco Switching/Routing :: Cisco 3750G Error During POST
Dec 5, 2011I am trying to configure a 3750G that has been sitting on the shelf for several months and am getting the following error -
% Error: Unable to create flash:/microcode_update% Error: It must not already exist
Normally, getting an error during POST isnt a good thing. My first thought was that flash was corrupted or flagged RO somehow. I did fsck flash: with no change. I next tried fsck /test flash:. It tested 77 blocks and performed 0 erasures. It had been running for about 15 minutes with no problems reported so far. Multiple reboots of the switch still report the same error.
I have reviewed the history of what I have done on this switch and finally think I found the problem. I noticed a microcode_update directory that I am not used to see on a 3750. Deleted the directory using the rmdir command and rebooted the switch. On reboot, I noticed that a front_end/ directory was listed as being created as well as fe_type_1 and fe_type_2 were created. The switch now boots up without any errors.
Cisco Wireless :: 2 Cisco Aironet 1401 APs Keep Kicking Users Off
Jan 3, 2013I have two Cisco Aironets 1401 connected to a Cisco Catalyst 3560 Switch. When users log onto the Wifi the APs authenticate with a Freeradius that then authenticates with LDAP.
Recently users have been getting kicked off of the network but I'm not sure why.If so how do I set these APs to roam with my setupd?For all I know there could be an issue with the switch I'm just not sure where to start when it comes to troubleshooting this issue.
Cisco :: CISCO Advanced Firewall On 2911 Router Using CCP?
Dec 29, 2012Guys I am using a cisco 2911 router with three interfaces: Gi0/0 connected through a switch to all my servers and Gi0/2 which will connect to another server, and Gi0/1 is my outside interface connecting through a switch to two ISP's.I have webservers and Terminal servers/File Servers with 10.0.0.0 network address connected throught My Gi0/0 interface.Now I want to implement a Cisco Advanced firewall for security on my router using CCP.I want the firewall to work such that it allows external users to access the servers on Gi0/0 through ports 0,23,25,20,21,53, 110,3389. and to access the SIP server on Gi0/2. My issue is can i just create two DMZ's for both interface Gi0/0 and Gi0/2 without creating an inside zone and Gi0/1 as outside zone as my internal traffic is mostly server based and the users connect remotely through terminal server to access resourcess using RDP, secondly how do I open the relevant ports.I have checked alot and all I have seen is just basic process on using the wizard I have no idea how to go about this issue.
View 19 Replies View RelatedCisco :: How To Connect Laptop To Cisco 3550 Switch
Mar 30, 2011I bought a new cisco 3550 switch to prepare for my Cisco certification prepration. Actually i dont know how to connect the cisco switch to a laptop with only usb ports....... earlier i used to do my practise using Cisco packet tracer but i think for CCNP switch that is not enough thats y i bought second hand switch. how can i connect that switch with my toshiba laptop which has only USB ports. do i need to buy some sort of convertor or other hardware. And if so what does u call it and how much does it cost?
View 5 Replies View RelatedCisco :: PPTP VPN To Pass NAT On Cisco 2921 Router
Apr 14, 2013I am struggling to have my PPTP traffic to get routed through NAT to reach other Server LAN segment. I am using Cisco 2921 router as a PPTP server.This Cisco 2921 router is working as PPTP server and doing NAT also to reach Server LAN segment (LAN-B).My problem is after PPTP connection establishes I cannot reach any of the LAN segment, but after connecting PPTP I can browse Internet without any issue, but none of the LAN element is reachable. Please have a look on the configuration I am posting 2921 router configuration to suggest something, I have also attached the network setup for better understanding…Just to update Clients in LAN-A can access Internet as well as servers (LAN-B). [code]
View 2 Replies View Related
