Cisco Wireless :: Connect Ap-1242AG With Non-cisco Router To Work As Repeater?
Nov 18, 2012is it possible to connect Cisco Ap-1242AG with non-cisco wireless router to work as repeater?
View 1 Replies
ADVERTISEMENT
Cisco Wireless :: Setting Up Wireless Repeater Using 1242AG Access Points?
Jul 4, 2011I have problem setting up wireless repeater using Cisco 1242AG access points. Here is the setup and problem - The location has 2 1242AG APs and a WLC (2206) which will be used by PDAs. One of the AP was converted to Lightweight AP and is wired. This AP is up and working and PDAs are able to connect to it. There is 1 WLAN and it uses Local EAP (LEAP) as authentication. Layer-2 security is configured as WPA/WPA-2 with 802.1X authentication. Under AAA servers Local-EAP is enabled and a profile (with LEAP enabled) is used. Local users are configured for login. As said PDAs are able to connect and it is working without any problem.
WLC (LEAP with local users) -----> LAP ----> Repeater AP
But the 2nd AP has to be configured as repeater was configured to repeater mode (refering to the document) and was placed. The WLC can see a client (with APs MAC address) but it is probing. The AP is still Automonous AP. Also username and password is configured for authentication. But still the radio on the AP is not up and it is in reset state.
Configure Wireless Router To Work As Repeater?
May 14, 2012I have here a canyon wireless router. do you know where I can find online a tutorial or manual on how to configure a wireless router so that it acts as a repeater?
View 3 Replies View RelatedCisco Wireless :: WAP2000 Work Smoothly As Repeater?
Jan 23, 2013Our customer setup requires an outdoor WAP (the main WAP) and two wireless signal repeters (that will be WAP2000). The repeaters will be powered over the Ethernet only and will be connected to the same switch as the main WAP (unknown vendor). My question is:
Will a WAP2000 work smoothly as a repeater when it's powered over Ethernet only and connected to the same switch as the main WAP is?
I noticed that WAP2000 connected this way was sort of 'lost' in deciding to repeat a signal or work as an independent wireless access point. The problem was immediately removed once the repeater was disconnected from the switch and powered from an outlet. I am not sure whether it was wrong addressing setup or something else that was needed to check/uncheck.
Make Dlink Dsl-2640t Router To Work As Wifi Repeater?
Sep 4, 2012make dlink dsl router 2640T to be working as repeater which will be able to receive wifi signals. I've seen one guy using the same dlink dsl-2640T as wifi signal repeater where he was successfully able to receive wifi signals[CODE]
View 5 Replies View RelatedCisco Wireless :: WAP4410N Work In Client-Repeater Mode?
Dec 7, 2009I have purchased 4 of these devices about 2 months ago and have experienced all of the issues reported within this thread. The came with the 2.0.0.5 FW rev installed, so unless the 2.0.0.5 on the cisco DL site is different, nothing I can do with that.I've tried making them work as stand alone AP's, Bridge<-> Bridge, etc... all modes seem to lock up eventually needing a reboot to get any functionality back.Ultimately, I need to make them work in AP<->Client-Repeater mode. I've not been successful in making them work in any mode for a prolonged period of time.
having just rfound this thread today, I have not tried hard coding the NIC's to 100/full, but will give it a try. If it works, great, but then that would defeat the purpose of buying an N radio AP. I would like the potential 300Mbps throughput.
Cisco Wireless :: Does WAP4410N Work As Repeater For Linksys E4200
Jun 15, 2011Does Cisco WAP4410N work as repeater for Linksys E4200 ?i have Linksys E4200 and I need repeater for it.
View 2 Replies View RelatedTP-Link 150Mbps Wireless :: TL-WR702N - Repeater Mode Signal Fades Out Or Does Not Work At All
Jan 31, 2013Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.107 Build 121123 Rel.31456n
ISP : COMCAST
This is the 2nd WR702N I have purchased. The first worked as a repeater for a short time and then failed with the fading symptom. I returned it. The second did not work as a repeater even for a short time. The signal is OK for a few seconds and then fades out. I updated the firmware.
How To Connect Repeater To Router
Sep 9, 2011How to connect repeator to router
View 1 Replies View RelatedConnecting Linksys Switch To Belkin Repeater / Bridge Won't Work?
Jun 24, 2011I am having a bit of trouble. I have a Belkin router (this is irrelevant) across the house, which is extended by the Belkin wireless bridge/repeater in my bedroom. The device in my room boosts my WiFi signal for my MacBook and iPhone, and the LAN (ethernet) port on the back allows my Debian server to connect to the network and internet. I have a Linksys switch that I wish to use, for I have another computer that requires an ethernet connection. Here is what happened:Debian 1 is connected via ethernet, no problem.I shut it down, unplug cable. Run cable from bridge to switch's uplink.Plug another ethernet cable into port one on switch, run it to Debian 1.
View 1 Replies View RelatedSetup Tenda W311R As A Repeater To Work With Linksys WTR120N?
Nov 27, 2011I tried to set up Tenda W311R as a repeater to increase the coverage. I have done the following, but still it cannot get Internet access:Set up WDS with the same channel and use the same encryption as the Linksys router; Disable the DHCP in the W311R;From the wireless point of view, I can see the Tenda router, but no Internet access.
View 3 Replies View RelatedConnect To Wireless Router When F1 Key Won't Work
Jun 11, 2011previously system was on internet explorer 8 and when turing on WAN only need to hit the F1 key, however since downloading internet explorer 9 and cd burner xp the f1 key isnt connecting me to wireless.
View 1 Replies View RelatedLinksys Wireless Router :: Cisco Connect Won't Work With E4200v1
Feb 4, 2013I've tried a number of ways to re-configure my E4200v1 router with Cisco Connect but without luck. I don't have the CD so I've downloaded it from this website and it loads and installs and launches but ultimately can never find the router. Part of the problem may be because I have a Verizon Fios Router already at 192.168.1.1. with the wifi and DHCP turned off, in favor of an Asus router which works well. I have tried taking the Cisco Connect installation off the wifi and onto a wifi through the E4200 Wan or Lan ports, but it still can't be found. I am able to get into the E4200v1 setting manually this way and to change its ip address to avoid the Fios Router conflict. But nothing works. Maybe I need to put the e4200 in the 192.168.1.1 range instead of the Asus 192.168.5.1 range? [code]
View 6 Replies View RelatedLinksys Wireless Router :: Cisco Connect E1000 Can't Work With Different Wifi
Feb 12, 20121. I set a router admin password different from WiFi password(passphrase).
2. I run my Cisco Connect app and it asks me to change my router admin password.
If I don't change it - I can not use Cisco Connect app.
If I provide my WiFi password then it changes my router admin password.
Maybe it was done to have a "simple" solution - 1 password for everything. But maybe its a bug because router admin password should be different from WiFi password fro security reasons.
Linksys Access Point :: Connect WRT54GL Router To Repeater To Establish WLAN Bridgde
Aug 27, 2012I got an Fritz Box from my new Provider to connect to the internet using Fiber To Home. the box is now im my living room and also acts as an WLAN Router. I would like to configure my WRT54GL which in located in my office from a router to a repeater to establish a WLAN bridgde.
View 3 Replies View RelatedCisco Wireless :: Aironet 1140s - How To Connect Repeater To Specific Access Point
Feb 12, 2013In our office, we have 3 Cisco Aironet 1140s and they are configured as follows:
* Access Point A (192.168.0.50)
* Access Point B (192.168.0.51)
* Repeater (192.168.0.49)
* SSID : 101
how to have the Repeater connect to Access Point A only?
D-Link DIR-655 :: Using As Wireless Repeater / Access Point / Bridge To Connect
Apr 12, 2011I have an ADSL2 connection at home served by a DLINK DSL-2760U modem+router . I also have a DIR-655 router.Is there any way I can use the 655 as a wireless repeater/access point/bridge to connect to the 2760U (reception issues between the floors)?
View 1 Replies View RelatedWireless Laptop Can Connect To Wireless Router But Internet Not Work
Jun 21, 2011I have wonder that my laptop has wireless, and when i connect it to router to use internet it show wireless now is connect, but when i open the website it show not work..and this problem occur only my computer. and when the other computer laptop they can connect and use internet normal...
View 1 Replies View RelatedLinksys Wireless Router :: E4200 V2 / Can Connect To Wifi Using Iphone But Emails Don't Work
Jul 13, 2012I have Linksys configured with IP 192.168.0.x and my local network ip 192.168.1.x have firewall connected to Adtrans box that gives us internet access via T1 line and other port is connected to the switch. Wireless router is connected to the switch using internet port.I can connect to wireless using iphone but emails don't work when connected to wireless. I tried to connect laptop to wireless is does not connect.
View 9 Replies View RelatedCisco Wireless :: Use Both CAP 3602i And LAP 1242AG On The Same Floor?
Oct 7, 2012On our conference floor, AP 1242AG already exist but I am going to add AP 3602i to increase wireless coverage. . Any issue or concern with this type of setting?
View 23 Replies View RelatedCisco Wireless :: Converting 1242ag To And From LWAPP
Apr 5, 2013is this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies View RelatedCisco Wireless :: Two 1242ag Bridge With 5gz At 800 Feet?
Sep 28, 2010I need to bridge from our office to our shop that is around 800 feet away. Here are the Details
I need the 2.4 ghz antenna for client access (Iphones are not compatiable with 802.11a) The locations are 800 feet away but are line of sight. I need to use the 5ghz antenna for the bridge i have 2 aironet 1242ag's I have 2 2.4 ghz AIR-ANT3213 antennas (planned for client access) I have 2 2.4 ghz AIR-ANT2506 (maybe useless for this)
My problem is that the range of all the listed 5 ghz antennas. None that i can find will bridge 54mb over the 5ghz radio for greater than 170ft
The closest that i can find is AIR-ANT5195. If i put these on both sides and it is outdoors line of sight, will the best i can hope for is functioning and 6mb
Are there options on 5ghz that i am missing.
Cisco Wireless :: WPA2 On Aironet 1242AG
Mar 9, 2012I am in the process of moving our office and part of the task involves relocating our existing wireless access points. They are all 1242AG's running the c1240-k9w7-mx.124-10b.JDA3 IOS. I would like to change the security on the access points to WPA 2 but that selection is not available. I think upgrading the IOS will solve this problem but I am not sure. So I guess I have two questions:
1) Does this Cisco model support WPA 2 ?
2) If so what IOS do I need to load to make WPA 2 available?
Cisco Wireless :: 1242AG Connecting To A Hotspot
Nov 7, 2012I need a temporary additional broadband connection at home and I was thinking about a bt openzone hotspot connection...
I have a cisco 1242AG access point which can do bridge mode. The BT openzone thing requires a username and password. Is it possible to connect the 1242 in bridge mode to bt openzone?
Cisco Wireless :: AIR-1242AG-A-K9 Mixing APs On WLAN
Jun 12, 2012What would be the ramnifactions of using AIR-1242AG-A-K9 (g radios only: no b clients) and AIR-LAP1231G-AK9 (g radios: only no b clients) with AIR- ANT1728 (non diversity antennas) on the WLAN. Some of the APs 1242/ 1231 will be with in line of site of each other.
View 1 Replies View RelatedCisco Wireless :: 1242ag Cannot Access With Browser
Nov 15, 2006I am new to cisco products and I am trying to setup an aironet 1242ag. I have figured out the ip given to it but, cannot access it with a browser.
View 6 Replies View RelatedCisco Wireless :: Maximum Possible Transmitting Power In 1242AG-E-K9
Feb 28, 2013My question is about the maximum possible transmitting power in a Cisco 1242AG-E-K9.I did an update of my AP on a new ios version and since then, the maximum power for me is limited to 17 dbm. I check this within the console and the "show controllers dot11radio0 | include Power:" command. I thought that I had 20dbm before the update, but unfortunately I can't proof this by myself because I have no AP left with the old firmware.
Is it possible that the upgrade did this? I read about the regulatory domains for the transmitting power. I live in Switzerland, so I thought I could use 100mW if I want to. I read it's not possible to use the 100mW at each speed but I think I should stull be able to select the 20dbm/100mW or am I missing something?
Cisco Wireless :: Loss Of Connectivity Through WLC 2504 And 1242AG AP
Oct 20, 2012I have an issue with a loss of connectivity after 10-15 seconds. I have a Cisco WLC 2504 controlling a Cisco 1242AG AP. The following is the topology.
Wireless Client -> 1242AG (AP) -> Port 3 WLC 2504 -> Port 1 WLC 2504 goes to fa0/2 on 3560. Port fa0/1 goes to ASA5505 (Inside)
All devices are on VLAN 10 10.50.1.0/24. AP is getting DHCP just fine and is associating with the WLC just fine. I connect my laptop to it and it connects just fine.
I then ping the gateway (ASA) 10.50.1.1 or the layer 3 interface on the switch 10.50.1.7 and it is fine for about 10 seconds, then it just dies then comes back in a few minutes and then goes away again. I have looked for duplicate IP's and can find none in any arp table.
It I just ping the controller 10.50.1.20 it is completely stable. I have moved the WLC directly off the ASA5505, moved the switch port, changed cables and the problem follows. I have even moved the AP to be directly off the switch instead of the WLC and the problem still occurs.
Cisco Wireless :: 1242AG - How To Find Out Model Of Antennas
Feb 25, 2013I have an existing 1242AG AP in a remote location, I have full access to it. I have a new 1242AG that was ordered but the client forgot to order antennas for it. Is there a way I can find out the exact model of antennas that are connected to the in place AP at the remote location??
View 2 Replies View RelatedCisco :: 1242AG / Configure Wireless Not To Be Shown For Users But Used By Them?
May 19, 2011How can I configure the wireless not to be shown for users,but used by them? On a Cisco 1242AG I mean when someone do a wireless discovery not see my wireless name, but typing the name be able to connect it.
View 5 Replies View RelatedCisco Wireless :: Determine Age Of A 1242AG Access Point?
May 22, 2013I have an AIR-LAP1242AG-A-K9, serial number FTX1623B0RX. I just need to know how old this unit is. (I haven't attached it to our Cisco account, so I can't open a TAC for it.)
Boot Version 12.4.13.0 IOS Version 12.4(23c)JA5Mini IOS Version 3.0.51.0
Cisco Wireless :: AP 1242AG Passing DHCP Requests
Jun 10, 2010I have 2 1242AG APs setup with one SSID and no vlans configured. The APs are connected to a switch along with my DHCP server. Clients are able to connect to the SSID but are unable to get an IP from the server. Clients can plug into the switch and get an IP. If I configure a static IP on the wireless card, the client works fine.
Is there something I'm missing on the AP to allow DHCP requests to pass through? IPhelper?
Here is the AP info: AIR-AP1242AG-A-K9 12.4(21a)JA1
Cisco Wireless :: 1242AG / Maximum Clients Connected To AP
Mar 11, 2012I have 1242AG. how many clients can be connected to this AP??
View 4 Replies View Related