I have an AIR-LAP1242AG-A-K9, serial number FTX1623B0RX. I just need to know how old this unit is. (I haven't attached it to our Cisco account, so I can't open a TAC for it.)
Boot Version 12.4.13.0 IOS Version 12.4(23c)JA5Mini IOS Version 3.0.51.0
I have 2 cisco 1242Ag APs in one building and 7 in other building installed in my infrastructure. All these 9 APs are connected to WLC and all of them are added to default ap group to broadcast all the ssid... But 7 in the second bulding are working properly, but the 2 in the other building are not broadcasting the ssids. I checked the configuration in both APs and WLC as well... All the 9 APs are having the same configuration.
View 12 Replies View RelatedI have a very special application where I need to connect as much as possible end devices to a single access point.The required data throughput per end device is very small - around 1 to 5 kbit/sec.I am using the Access Point Aironet 1242AG.
Questions :
1. What is the maximum number of simultaneous users that can be connected to a Cisco Access point, is it 255 or can be more ?
2. If I define multiple SSID’s, what if the total numbers of users that can be connected to a Cisco Access point
3. I there a simulator tool that can be used to simulate multiple wireless connections to an AP
4. Have anyone tested so many users connected to 1 Access point ?
I have the wireless controller 5508 and many AP1261 registered on site. It detects a lot of rogue access points around. I would like to find out geographic location of these rogue access points. Is it possible?
View 2 Replies View RelatedI have configued Cisco LAP 1242AG with statis IP.I have connected LAP to WLC.I am able to ping WLC management interface IP Address from LAP's console.LAP is failed to Join WLC with error "Could not resolve CISCO-SAPWAP-CONTROLLER"
View 3 Replies View RelatedI am trying to determine the best option for extending my home network. I am currently running an E2000 as my router and am considering the purchase of a Valet Plus to use as only an Access Point. Alternatively I have a used E1000 in good condition. Which would be best for use as an Access Point only?
View 1 Replies View RelatedI am new to cisco products and I am trying to setup an aironet 1242ag. I have figured out the ip given to it but, cannot access it with a browser.
View 6 Replies View RelatedI have an existing setup of older 1242AG-E-K9 access points with Air-ANT-ANT5160 antennas connected to them. Goal is to replace old AP's with new AIR-LAP1262N-E-K9 model. Question is that can I use only one antenna per radio? Does it work? I know that N-standard requirement is 3 antennas per radio (3 x 2.4G and 3 x 5G) but we need only B/G to work. Plan is to re-use existing AIR-ANT-ANT5160's and order new AIR-ANT2506 antennas. Setup per AP would be 1 x 2.4G and 1 x 5G.
View 7 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI have problem setting up wireless repeater using Cisco 1242AG access points. Here is the setup and problem - The location has 2 1242AG APs and a WLC (2206) which will be used by PDAs. One of the AP was converted to Lightweight AP and is wired. This AP is up and working and PDAs are able to connect to it. There is 1 WLAN and it uses Local EAP (LEAP) as authentication. Layer-2 security is configured as WPA/WPA-2 with 802.1X authentication. Under AAA servers Local-EAP is enabled and a profile (with LEAP enabled) is used. Local users are configured for login. As said PDAs are able to connect and it is working without any problem.
WLC (LEAP with local users) -----> LAP ----> Repeater AP
But the 2nd AP has to be configured as repeater was configured to repeater mode (refering to the document) and was placed. The WLC can see a client (with APs MAC address) but it is probing. The AP is still Automonous AP. Also username and password is configured for authentication. But still the radio on the AP is not up and it is in reset state.
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
On our conference floor, AP 1242AG already exist but I am going to add AP 3602i to increase wireless coverage. . Any issue or concern with this type of setting?
View 23 Replies View Relatedis this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies View RelatedI need to bridge from our office to our shop that is around 800 feet away. Here are the Details
I need the 2.4 ghz antenna for client access (Iphones are not compatiable with 802.11a) The locations are 800 feet away but are line of sight. I need to use the 5ghz antenna for the bridge i have 2 aironet 1242ag's I have 2 2.4 ghz AIR-ANT3213 antennas (planned for client access) I have 2 2.4 ghz AIR-ANT2506 (maybe useless for this)
My problem is that the range of all the listed 5 ghz antennas. None that i can find will bridge 54mb over the 5ghz radio for greater than 170ft
The closest that i can find is AIR-ANT5195. If i put these on both sides and it is outdoors line of sight, will the best i can hope for is functioning and 6mb
Are there options on 5ghz that i am missing.
I am in the process of moving our office and part of the task involves relocating our existing wireless access points. They are all 1242AG's running the c1240-k9w7-mx.124-10b.JDA3 IOS. I would like to change the security on the access points to WPA 2 but that selection is not available. I think upgrading the IOS will solve this problem but I am not sure. So I guess I have two questions:
1) Does this Cisco model support WPA 2 ?
2) If so what IOS do I need to load to make WPA 2 available?
I need a temporary additional broadband connection at home and I was thinking about a bt openzone hotspot connection...
I have a cisco 1242AG access point which can do bridge mode. The BT openzone thing requires a username and password. Is it possible to connect the 1242 in bridge mode to bt openzone?
What would be the ramnifactions of using AIR-1242AG-A-K9 (g radios only: no b clients) and AIR-LAP1231G-AK9 (g radios: only no b clients) with AIR- ANT1728 (non diversity antennas) on the WLAN. Some of the APs 1242/ 1231 will be with in line of site of each other.
View 1 Replies View RelatedHow do I determine the speed of my wireless components?
View 2 Replies View Related