Cisco Routers :: RV082 - Stopping Any Communication On Dell Powerconnect 5424
Feb 25, 2013
I have a RV082 router that is currently in prod. I have a Dell Powerconnect 5424 switch that I'd like to use in place of the unmanaged switches I am currently using.
I have the switch configured with it's IP, subnet, gateway, etc. I can plug devices into it and communicate with no problems. However, when I attempt to plug in the router, nothign will communicate to or from the switch. The devices I plugged in will not talk to each outer, ping the switch, or the router. Also cannot ping to the switch from a device plugged into the router. If I unplug the router, comm opens back up.
View 1 Replies
ADVERTISEMENT
Feb 26, 2013
I have a RV082 router that is currently in prod. I have a Dell Powerconnect 5424 switch that I'd like to use in place of the unmanaged switches I am currently using.I have the switch configured with it's IP, subnet, gateway, etc. I can plug devices into it and communicate with no problems. However, when I attempt to plug in the router, nothign will communicate to or from the switch. The devices I plugged in will not talk to each outer, ping the switch, or the router. Also cannot ping to the switch from a device plugged into the router. If I unplug the router, comm opens back up.
View 1 Replies
View Related
Jan 13, 2013
I have just purchased Dell PowerConnect 6224? how can i create two VLANs (vlan 10 - 192.168.10.x/24 & vlan 20 - 192.168.20.x/24) that can communicate with each other without setting servers/workstation network gateway point to the vlan ip address?
View 2 Replies
View Related
Nov 16, 2010
I managed on my own to figure out how to Telnet in, activate the web control panel, and then access that via the web. Now here is what I am trying to do, it is not that complicated. We have a FIOS connection with 5 IPS: FIOS comes in as Ethernet, without DHCP.
What I want to Assign to Ports on the Switch:
1) Uplink to FIOS
2) VOIP PBX
3) Point of Sale System
4) Internal Network
5) Public Wifi
6-8: Not in use
Each of the above 2-5 will have a router connected to the switch port, each is a separate segregated network, with its Own public IP.
I want to configure the switch to prioritize traffic in the following manner:
Port 2: VOIP: Always gets TOP priority, then Port 3: PoS (but not that important), then port 4: internal (less important), then port 5: public wifi (least important).
View 1 Replies
View Related
May 22, 2011
I recently purchased a used 2716, and I just can't seem to access the web interface.i have a Cat5e cable running from my router to Port 1 of the switch. I have my laptop connected to Port 16 via a Cat6 cable.
I have internet access both on managed and unmanaged modes, so that's working just fine. I can't seem to access the web interface however. I've tried both IE9 and FF4.
I followed the instructions to hold down the "Managed Mode" button for 30 seconds, and then wait for the switch to reboot. I've done this a few times just to be sure. This should reset it, but when I try to access 192.168.2.1, it just tells me it cannot access this page.
View 15 Replies
View Related
Oct 28, 2012
I just purchased a SG300-10 switch and loaded the newest 1.27 firmware on it. Setup my VLANS and trunks but I have this weird issue. My setup:
I have the SG300-10 as my main switch and changed it over to L3 so it can be my main core in my small network. On port 1, vlan 200 is setup as my native PVID untagged and I have it set to trunk vlan's 210(LAN network), 220 (management vlan) tagged over to a Dell powerconnect 5224 24port switch. On port 1 of the Dell switch, I have it setup as a trunk there as well with the same setup (native PVID vlan set to 200 untagged, trunking 210 and 220 tagged).
View 12 Replies
View Related
Feb 23, 2012
I have no previous Cisco switch experience. I just received a brand new SG200-08 switch. It replaces a small blue Trendnet 5 port switch. I configured the SG200-08 with a static IP address which is on the same subnet as all our wired devices, then I installed it and connected a computer and printer and another switch to it. The other switch is a Dell PowerConnect 2716. I suddenly have no network connectivity with the router any longer. When I plug the network cable that runs from the PowerConnect 2716 into the SG200-08, the link status light will not go on for that port. I am going to be replacing the Dell PowerConnect with a Cisco switch as well, the SG300-10.
View 6 Replies
View Related
Sep 23, 2012
I'm configuring a 2 PowerConnect in stack mode. I can't seem to resolve this error - Recieved Frame Check Sequence Errors.Both stacks are in the lastest firmware version 3.3.4.1. Physical connections are tight.
View 1 Replies
View Related
Aug 10, 2011
I have RV 120W Wireless-N VPN Firewall and having issues with connectivity and communication between PCs within the same LAN. I tried the following to check connections:
1. Finding the computers within the workgroup using wondows network or (finding the computer) without avail.
2. Pinging the IP address of the PCs within the LAN. Request Timeout is given.
3. Pinter Network is working fine.
View 6 Replies
View Related
Oct 26, 2011
I just bought an XPS 8300 brand new.After woeking OK a few days, now it connects to the Broadcom Netlink Communication card only after rebooting 3-4 times at cold-start.
All the other home computers are connecting from the first shot. (two laptops and another desktop. They much slower computers.At the begining I have re-installed the driver (from DVD and downloaded), but not this is the problem.
The computer has to get a bit warm.When it does not connect, the Dell Test tool DOES NOT SEE (does not appear in the test list) the Broadcom NetLink Gigabite Ethernet card.
View 285 Replies
View Related
Feb 9, 2011
I have a 2 router and each one have separate network with DHCP and IP of the two routers are 10.4.251.1 and 10.4.252.1. I am using linksys WRT54gl router with tomato firmware.how can i make communication between these two networks. I want access files from 10.4.251.x to 10.4.252.x and vice versa.
View 1 Replies
View Related
Jun 25, 2012
how to communicate between different networks in router .I know by using BGP we can communicate only in the same network only.
View 2 Replies
View Related
Apr 26, 2012
I recently bought this router for its great throughput and V LAN capabilities. It replaced a standard Linksys DIR-655.But now I am having trouble connecting my Samsung Galaxy2 (Android 4.0.3) telephone to my computer. Telephone is connected to WI-fi and computer is connected to wired LAN. When starting Kies on my telephone (this is a web server app) it tells me to connect to http://192.168.1.202:8080/ on my computer. This is the correct IP address for the telephone (I have reserved it on the router) and firewall is OFF in windows 7. But there is no response with Firefox or IE8. I have not changed anything on either the computer or the telephone since I replaced the router, so the problem must somehow be linked to the router.
Both telephone and computer are connected to the internet OK. I can even remote control the computer from the telephone using the VNC app on the telephone!So the network IS working. The problem is only related to the communication with the Kies app.
View 2 Replies
View Related
Sep 6, 2011
I have three routers and 2 ISPs but I'd like to focus for now on a configuration with only one ISP provider. Here is my environment:
Netgear Cable (CBVG834G) wireless routerON the cable router are connected multimedia type equipments (TV/ IP set top box/ IP amp ) located on the family room DHCP ON (because I can't get internet connectivity when I assigned Fix IP address I come to that later) IP Adress:192.168.1.2 DHCP range:192.168.1.10/ 19 Reserved IP : 1292.168.1.10 for the Dlink 4 DEV a connected D-LINK ( DIR-855) wireless router.mainly PCs, NAS (x2) located on the first floor. DHCP ON Lan IP Adress: 192.168.0.1 DHCP range:
192.168.0.100 / 120 WAN Ip address : 192.168.1.10 6 PCs are connected
Everything works fine from an internet connectivity standpoint:
DEVx can connect to internet fine
PCx can connect to internet
PCx can access DEVx
Now the issue DEVx can't access resources from PCx!
View 4 Replies
View Related
Aug 9, 2012
I have 2 different network topology - network A and network B Both of them are connecting to the same gateway (a firewall) to the net. they're using the same range of public IP pool to NAT the private IPs. in shorts, all setup is almost the same except the devices' brand between A and B.I have no problem to access the webpage using network A. But whenever I attach the same laptop to network B, the same page won't display at all.I've done wiresharking to network B and the result shows "ICMP destination unreacheable (Communication administratively filtered)" which reported by unknown device (suspected to be the webpage's gateway).
View 5 Replies
View Related
Aug 7, 2012
We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
View 12 Replies
View Related
Jan 29, 2013
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
View 4 Replies
View Related
Nov 17, 2011
isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
View 4 Replies
View Related
May 9, 2013
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
View 1 Replies
View Related
Nov 12, 2012
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies
View Related
Jan 12, 2012
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies
View Related
Jan 14, 2013
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
View 4 Replies
View Related
Jan 24, 2012
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
View 7 Replies
View Related
Jul 28, 2010
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
View 20 Replies
View Related
Mar 15, 2013
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies
View Related
Jul 18, 2012
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
View Related
Oct 20, 2011
Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
View 7 Replies
View Related
Jan 9, 2012
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
View 0 Replies
View Related
Apr 27, 2013
we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
View 0 Replies
View Related
Nov 12, 2012
I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies
View Related
Sep 25, 2012
I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies
View Related
Mar 24, 2013
We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
View 8 Replies
View Related
Feb 10, 2013
I'm planning to buy a few Cisco RV082's for remote offices and using them to connect to main office Cisco 2851 site to site vpn. So I guess, simple site to site vpn will work without much problem, but I wonder, will backup vpn feature work as expected on backup WAN channel and how should I configure it on the IOS side?
View 1 Replies
View Related
