Cisco Switches :: Can SG200-08 Switch Work With Dell PowerConnect 2716
Feb 23, 2012
I have no previous Cisco switch experience. I just received a brand new SG200-08 switch. It replaces a small blue Trendnet 5 port switch. I configured the SG200-08 with a static IP address which is on the same subnet as all our wired devices, then I installed it and connected a computer and printer and another switch to it. The other switch is a Dell PowerConnect 2716. I suddenly have no network connectivity with the router any longer. When I plug the network cable that runs from the PowerConnect 2716 into the SG200-08, the link status light will not go on for that port. I am going to be replacing the Dell PowerConnect with a Cisco switch as well, the SG300-10.
View 6 Replies
ADVERTISEMENT
May 22, 2011
I recently purchased a used 2716, and I just can't seem to access the web interface.i have a Cat5e cable running from my router to Port 1 of the switch. I have my laptop connected to Port 16 via a Cat6 cable.
I have internet access both on managed and unmanaged modes, so that's working just fine. I can't seem to access the web interface however. I've tried both IE9 and FF4.
I followed the instructions to hold down the "Managed Mode" button for 30 seconds, and then wait for the switch to reboot. I've done this a few times just to be sure. This should reset it, but when I try to access 192.168.2.1, it just tells me it cannot access this page.
View 15 Replies
View Related
Dec 20, 2011
Im currently working on setting up a small network at home. I have a Dell 2716 and a dell 2650 server running windows server 2003. Ive already setup the dns and domain controller on my server. I have 3 desktops that will connect to the server. so far I have the following setup. ISP---> Dell 2716 --->dell 2650/ computers. I set the computers prefered dns to the servers ip. Im able to join the domain and log in but is there a better way to set it up. Also the server and computers are set to static ip.
View 2 Replies
View Related
Oct 28, 2012
I just purchased a SG300-10 switch and loaded the newest 1.27 firmware on it. Setup my VLANS and trunks but I have this weird issue. My setup:
I have the SG300-10 as my main switch and changed it over to L3 so it can be my main core in my small network. On port 1, vlan 200 is setup as my native PVID untagged and I have it set to trunk vlan's 210(LAN network), 220 (management vlan) tagged over to a Dell powerconnect 5224 24port switch. On port 1 of the Dell switch, I have it setup as a trunk there as well with the same setup (native PVID vlan set to 200 untagged, trunking 210 and 220 tagged).
View 12 Replies
View Related
Sep 24, 2012
My switch Cisco small business SG200-26G in modality link aggregation LACP the Wake On Line doesn't work !! (WOL work only in link aggregation non LACP..) I already upgrade the latest firmware but not resolved..
View 4 Replies
View Related
Jan 7, 2013
I have a problem with my SG200-08 Switch the switch not forwarding a special Packet. I try to run a simple Profinet installation for testing on the switch but it didn't work correct. A special packet (Profinet error message) was not forwarded.
I have tried it with different Profinet masters with Siemens Profinet master it works without of problems. With Rexroth master it dosn´t work. But it is the same packet only another Mac Address.
I have added two Wireshark logs, where I have mirrored the slave and the master port. With the Siemens master all packets are forwarding (every packet is double longed) with the Rexroth master the alarm packet was not forwarding (the alarmpacket is lost between the ports).
With a not managed Switch it is no problem too run both Installations correct. I have tried the Factory default Settings of the switch and too deactivate all services of the switch (like Spanning Tree, ..) but it was all the same, the Packet was not forwarded.
View 8 Replies
View Related
May 27, 2013
I had a SG200-8/SLM2008TNA switch that I was using on my lab network (192.168.9.x)One of my clients had an emergency so I moved the switch to their network (10.1.2.x)I can't see the switch at all! Cisco FindIt toolbar won't discover it (other switches on the client network are discovering OK)I changed my computer's IP to the range where the switch used to live...still can't find it I also don't see any new devices in DHCP with cisco-looking MAC addresses.Of course, the SG200-8 doesn't have its MAC address printed anywhere on it, and doesn't have a factory reset button.It's passing traffic OK but I was hoping to get it configured via web console and set for SNMP monitoring. how to discover/reset IP/factory reset this thing?
View 2 Replies
View Related
Aug 28, 2011
We have 2 of the SG200-26 switchs. When ever we loss power all the settings are reset to default. Even if we loss power for 1 min. This includes the IP, user, password, etc. How can I change this so the settings are saved?
View 1 Replies
View Related
Mar 9, 2013
Cisco SG200-26 (not PoE model). After a power failure, at restart the switch seems unable to reboot. The power led starts blinking in green, after some seconds the connected ports start blinking as well, but the the switch reboots automatically after few more seconds.I tried to disconnect lan cables, power cord, and reset to factory by pressing and holding down the proper button for 30s and more, but no success.In the small amount of time the switch's ports seem to be powered up, clients don't receive packets, don't ping each other or the switch manage address.
View 1 Replies
View Related
May 9, 2012
I start writing this post telling you that I'm not a qualified network admin, so I beg your pardon if I do not use appropriate terms in my question. Also my english in not so good since I'm Italian and my english in almost scholastic.
This is the "story" :
I bought two switches as described above and actually I have to create 2 VLANS as described below :
VLAN id 2 name "Service_A" ports 1-4
VLAN id 3 name "Service_B" ports 7-9
all other ports can stay in default VLAN1.
my network infrastructure have some other very simple swtiches connected and 1 soho router (static ip 192.168.1.1) with dhcp active and ip pool address released from 192.168.1.100 to 200.
the SG200-26 have static ip 192.168.1.254 and 192.168.1.253
MY NEEDS:
I need VLAN for privacy matter so all computer connected to ports in VLAN2 cannot see nor enumerate PCs and resources on other VLANs, but I also absolutely NEED that all computer in every ports (and every VLAN even default VLAN1) can access the internet.
View 1 Replies
View Related
Jun 29, 2011
I have just recently replaced a WS-CE500-24LC switch with a SG200-50P. I have plugged in a Cisco 1760 router with a fast ethernet into the switch. On the console of the router I now see these messages: [code]
As far as I am aware both ends of the link are set to autonegotiate the speed and duplex.
View 2 Replies
View Related
Oct 17, 2011
Last week and just yesterday, our switch SG200 50/50 logged an error like this:
%CDP-E-MALFORMED_TLV: CDP message from 88:43:e1:ab:66:f8 cached with illegal Appliance VLAN-ID TLV
At the time of the error, the SA520 router's LAN Port 1 where the SG200 Port 49 connected went down. (Light is OFF) So internet is down and other V LAN are disconnected. The MAC address on the log is the SA520 router. This happens 2x now and it needs for me to reboot both switch and router. and goes back again online.
SG200 50/50 Port Firmware 1.1.1.8
SA 520 Firmware (Primary/Sec):2.1.51/2.1.18
View 4 Replies
View Related
May 24, 2011
SG200-08 and SG200-08P fail to hold or update Date/Time.(New installation for a UC320 setup.)I've got both an SG200-08 and SG200-08P that are failing to maintain date/time when set with "Use Local Settings". Every restart/powercycle causes them to reset to Dec 31 1969. Other settings save fine.I first tried to set time via SNTP Unicast using a variety of public time server addresses including the 3 hard coded to the SG200-08 firmware:
Sadly though it always just shows "Active Server Server Host Address: 0.0.0.0" and continues having 12/31/1969 as the date. Both after a config save and a reboot.I can ping the NTP servers just fine from the switches either by IP or by hostname.At this point I've decided that I must be missing something simple. At least I hope so... otherwise it's a firmware bug which means waiting for a fix.Other devices behind the same firewall/gateway (RVS4000) are updating NTP
View 2 Replies
View Related
Jan 21, 2012
I'd like to use an SG200 swicth to allocate bandwidth on a 100 Mbps fiber Internet uplink.I will have 5 routers (each supporting a separate network) connected to the SG200, and I'd like to give each network 20 Mbps. QOS configuration, best CIR and CBS settings for this.
View 1 Replies
View Related
Apr 29, 2012
how to connect our new SG200-18 to an existing Cisco network, in particular a C2960S.Here's what I've got:
<----- Rest of network ------- C2960S ----------- SG200 ----- (PC connected directly to the SG200)
On the C2960S-side here's what I've got on the corresponding interface:
interface GigabitEthernet1/0/1
switchport mode trunk
On the SG200-side I've set the IP-address and default-gateway accordingly, however:From the SG200 I can't ping any other host on the same IP-subnet as the switchFrom the SG200 can't ping the default-gatewaycan't ping from any other host or the default-gateway *to* the switch But:On the SG200 I've got plenty of MAC-addresses under "Dynamic Address Table" - however only MAC-addresses that belong to the management-VLAN of the SG200 (i.e. VLAN9 in my case)The MAC-address table on the SG200 even includes the MAC-addresses of hosts on the same VLAN I tried to ping without success. For example: I tried a PING from a host having a MAC-address of 00:19:bb:31:91:30. This MAC shows up in the arp table of the SG200. To cross check I connected a dedicated PC to the SG200 and assign it an IP-address out of the management-LAN-range of the SG200 - in this case I can access the switch (i.e. PING, WEB etc.)So to summarize: Connectivity is OK when going from directly connected devices to the SG200. No connectivity from devices that are behind the C2960S towards the SG200 and vice versa. (The problem is definitely not with the C2960S-side since we've got plenty of them hooked together without problems.) I'm enclosing the screenshots of the corresponding definitions on the SG200.
View 4 Replies
View Related
Apr 16, 2013
I'm baffled by the poor performance that I'm seeing when passing traffic between my two Cisco SG switches.
The configuration is as basic as I can make it, no VLANs, QoS or bonding. Both have been updated to current firmware as part of the troubleshooting process.
When I transfer data within one of my switches I see 50/60Mb/s. When I pass the same traffic between both switches I see 0.6 Mbs/ or less.
I have tried to eliminate every possible factor including switching out the cables. No success.
View 2 Replies
View Related
Jan 13, 2013
I have just purchased Dell PowerConnect 6224? how can i create two VLANs (vlan 10 - 192.168.10.x/24 & vlan 20 - 192.168.20.x/24) that can communicate with each other without setting servers/workstation network gateway point to the vlan ip address?
View 2 Replies
View Related
Nov 16, 2010
I managed on my own to figure out how to Telnet in, activate the web control panel, and then access that via the web. Now here is what I am trying to do, it is not that complicated. We have a FIOS connection with 5 IPS: FIOS comes in as Ethernet, without DHCP.
What I want to Assign to Ports on the Switch:
1) Uplink to FIOS
2) VOIP PBX
3) Point of Sale System
4) Internal Network
5) Public Wifi
6-8: Not in use
Each of the above 2-5 will have a router connected to the switch port, each is a separate segregated network, with its Own public IP.
I want to configure the switch to prioritize traffic in the following manner:
Port 2: VOIP: Always gets TOP priority, then Port 3: PoS (but not that important), then port 4: internal (less important), then port 5: public wifi (least important).
View 1 Replies
View Related
Feb 25, 2013
I have a RV082 router that is currently in prod. I have a Dell Powerconnect 5424 switch that I'd like to use in place of the unmanaged switches I am currently using.
I have the switch configured with it's IP, subnet, gateway, etc. I can plug devices into it and communicate with no problems. However, when I attempt to plug in the router, nothign will communicate to or from the switch. The devices I plugged in will not talk to each outer, ping the switch, or the router. Also cannot ping to the switch from a device plugged into the router. If I unplug the router, comm opens back up.
View 1 Replies
View Related
Dec 14, 2010
8 Port Gigabit Switch, HP 1810-8G, Netgear GS108Tv2 and Dell PowerConnect 2808, which one is better for LACP Link Aggregation?
The Netgear GS108Tv2 has more function than the other two, but I don't know the Netgear is stable or not?
View 5 Replies
View Related
Sep 23, 2012
I'm configuring a 2 PowerConnect in stack mode. I can't seem to resolve this error - Recieved Frame Check Sequence Errors.Both stacks are in the lastest firmware version 3.3.4.1. Physical connections are tight.
View 1 Replies
View Related
Sep 9, 2012
I have a SF 300-24 24-Port 10/100 Managed Switch and I am trying to set some VLANs. The image below shows how I want it to be setup:Since the remote site goes through the Internet, making port 20 an 802.1Q trunk over the two VLANs will give WAN connectivity to VPN/E-mail.I've tried all sort of settings [ see attachments] but can't get it work.
View 5 Replies
View Related
Dec 2, 2012
We have a project in which we are using 34 Cisco SG200-18's each with a MGBLX1 (LC Single Mode Fiber) SFP mini-GBIC.All the fiber's come back to one building where we must "bridge" all 34 fiber connections. What hardware should be used to accomplish this? A L2 switch? For example, a 12 port SFP Switch with Fiber SFP's accepting the first 12 fiber connections, then other switch with SFP for the next 12 and so on, until there is a overall capacity of 36 and having patch cables between the 3 switches?
what cisco or non cisco hardware would work with these SF200-18's to accomplish this?
View 9 Replies
View Related
Jun 2, 2012
I am trying get inter vlan routing to work on a DF 300 - 24 port switch. I have an existing company network on 192.168.111.0 and want to create a vlan on 192.168.1.1 that can talk to 192.168.111.0. I have enabled layer 3 routing on the switch via console and also provided the ip routing command. I have the following VLAN's:
VLAN1 - Default 192.168.111.0
VLAN2 - 192.168.1.0
I have enabled DNS and provided my two DNS servers 192.168.111.82 & 192.168.111.212. I have set the VLAN1 interface to 192.168.111.217 and VLAN2 interface to 192.168.1.1.
Ports FE1 - FE15 are set to access ports and assigned to VLAN1 (untagged)
Ports FE16 - FE24 are set to access ports and assigned to VLAN2 (untagged)
I have set a default route for the switch to 0.0.0.0 0.0.0.0 192.168.111.254 (Draytek 2600 router). I have connected a computer (A) to VLAN1 port FE3 and a computer (B) to VLAN2 port FE16. I have set Computer A default gateway to 192.168.111.217 and its IP address to 192.168.111.94. I have set Computer B default gateway to 192.168.1.1 and IP to 192.168.1.2.
Computer A has access to Mdaemon, file server via network drives but no internet (cannot ping google) and can ping computer B and RDP onto computer B.
Computer B can ping computer A and RDP onto computer A but does not have access to the company network i.e MDaemon, file server etc. It also cannot access the internet.
From the console I can ping [URL]and all ip addresses in the company network i.e. 192.168.111.82 (DNS server). If I scan computer A wirh wireshark the internet starts working weird!
Configuration show below:
switch7c0a71#show run
vlan database
vlan 2
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
[code]....
View 40 Replies
View Related
May 16, 2012
We are replacing some netgear switches with the Cisco SG200. The situation is relatively straightforward. We have a series of VLAN's coming in on a trunk from a service provider for our Metro Ethernet locations. These trunks then get cross-connect to various location for connectivity. The problem we have is there are two VLAN's that need to go to the same switch which provides access to our public IP block.
I set up the two VLAN's on the SG200 with the trunk port VLAN tagging on the service provider port. Then I set up a separate port for untagging the traffic with the PVID of the respective VLANS's as follows: [code] The public switch has no VLAN's configured (it is an SG200 too). If I connect GE2 to the public switch everything works fine. When I connect GE3 to the public switch, things die. I thought this might be caused by STP although STP should not be detecting issues like this across separate VLAN's. Disabled STP, no change.The same configuration with the Netgear worked without an issue. FYI, the VLAN's cannot be changed...they are defined by the service provider in this particular case. otherwise we'd just make them the same..
View 11 Replies
View Related
Aug 28, 2011
I need to purchase a few Gigabit PoE switches for a small business and I am thinking that SG200 or SG300 switches are perfect for this purpose.
Layer 3 functionality in SG300 switches is not great - HSRP or any other next-hop redundancy protocol is not supported, dynamic routing protocols are not supported, policy-based routing is not supported, etc. I may get one SG300 switch for inter-VLAN routing so that I do not have to send traffic to a Layer 3 device for this purpose, especially because my Layer 3 device (ASA5505) has only 10/100 Mbps interfaces. All other switches in the network don't have to be Layer 3 switches, and I am thinking of perhaps getting SG200 instead of SG300 swithces. However, because I am a long-time Cisco engineer, and know ins and outs of the IOS CLI, I would much rather administer the switches with CLI rather than GUI. So, do SG200 switches provide CLI (even if it is not officially supported) or is the only Small Business switch platform that supports CLI SG300? I do realize that the OS running on these switches is not IOS, but after having reviewed the CLI manual for SG300, I would say that 90+% of commands are identical to IOS CLI commands.
View 1 Replies
View Related
Dec 27, 2012
I just picked up a pair of 18-port SG200s, and I'm trying to figure out of there's some secret trick to getting CLI access to them? I've upgraded to the latest version of firmware (1.2.7.76) hoping that may work, but no luck.I can tell the guts to support a CLI are there, because writing the config out to a TFTP server shows identical an identical config style to the SG500 I have here.Is there some way to enable it?
View 5 Replies
View Related
May 22, 2011
I am trying to set up three vlans across two switches. The switches are Cisco SG200 and SG 300 series. There are 20 devices connected to the two switches including a router for Internet. Among these devices are five wireless access points all hardwired to the LAN. If I understand correctly the first thing I have to do is aggregate the two switches. I ran two cat5 cables to ports 1 and 2 of each switch. As I understand it all I need to do is to create SAG with the two ports on each switch. I think I need to use tagging but I don't really understand how to do this. Once I get the trunking set up correctly I want to create one vlan to which all devices will belong for Internet access. The other two would be for data and VoIP. Do I create vlans with the same name on both switches? When I assign the devices (by port) do I need to enable tagging? Which type of port setting should I use? I am assuming that by including the acess points in the vlans will mean that any wireless device connected to them will have acess to the Internet and the devices in the same vlan.
View 1 Replies
View Related
Oct 23, 2012
1) SG200-18 configuration
- VLAN 10 and 20
- VLAN 10: Port 1 tagged, Port 14 untagged
- VLAN 20: Port 1 tagged, Port 13 untagged
- Port 1: 1UP, 10T, 20T Admit tagged PVID 1
- Port 14: 10UP Admit untagged PVID 10
- Port 13: 20UP Admit untagged PVID 20
Port 1 connected to Fiber ONT (On VLAN 10), Port 14 connected to RV042G WAN.Once RV042G LAN connects to SG200-18 (VLAN 1) port, RV042G WAN unable to get public IP and internet connection gone, port 14 showing "Discarding" under "Spanning Tree"
View 17 Replies
View Related
Apr 27, 2013
whether or nor we would see a performance boost by upgrading our current switches.
Our Setup:
Comcast internet
2 x Dell 2724 switches connected together with a patch cord
Dell server with 6 core CPU
We have about 25 workstations that access the server, which is running a SQL database. The usage is pretty light, so probably only 2 or 3 users would even be active at one time.
We added several networked printers and we ran out of ports on the current 2 switches. So now we need to add in a third Dell 2724, or we were thinking about upgrading to something like a Dell 5548 plus a Dell 5524 or a few Cisco SG300.
I don't think we need any of the advanced features of these switches, but in simple terms, will we recognize a real world performance boost from upgrading?
View 9 Replies
View Related
Dec 14, 2011
I have currently a Dell powerconnect 6248 switch combined with a netgear UTM router. I have a basic understanding on how things should work but I don't have the knowledge to apply it as I'm new to setting up vlan and the person before me did the basic configuration like this:
defined 5 VLAN in the netgear router
defined the same 5 VLAN in the dell 6248
connected the dell switch to the netgear router via a trunk port.
Right now all the inter vlan traffic pass thru the netgear router as the dell switch as a trunk port connected to the netgear box who then give dhcp and set himself as the default inter vlan route. I would like to stop that since I would like the cisco switch to handle all the vlan routing for both switch and those switch to send their dhcp request to my win2k8 server.
I did set the sge2010 in layer 3 mode from the small business telnet interface. I then setup the same 5 vlan in the cisco switch.
If I understand this well I need to define an IP address for each vlan interface on the cisco switch for it to be able to route things, I have set them all as x.x.x.3 (x.x1.3 vlan 1, x.x.2.3 vlan2, etc) Then I need both swtich to forward all dhcp request to my dhcp box wich is in vlan 2. My DHCP server will have 5 range of IP address to hand out. my server are connected directly to the dell switch on vlan 2. I have set up a port in the dell switch in trunk mode and did the same thing in the cisco switch and connected them togheter to send all vlan packet. The current setup doesn't work so I need to finalize that setup so that everything works.
View 1 Replies
View Related
Dec 15, 2011
With the new firmware (1.1.2.0) released for SG200 switches, is there CLI now?
View 4 Replies
View Related
May 22, 2013
I am trying to connect an SG200 to a customer's existing network. The customer does not want to receive any bpdu frames from the SG200. The customer's port has bpdu guard configured to err-disable their port upon receipt of a bpdu.
How do I completely disable spanning tree on the SG200 so that it does not send any bpdus?
View 3 Replies
View Related
