Home Network :: Powerconnect 2716 And Webserver
Dec 20, 2011
Im currently working on setting up a small network at home. I have a Dell 2716 and a dell 2650 server running windows server 2003. Ive already setup the dns and domain controller on my server. I have 3 desktops that will connect to the server. so far I have the following setup. ISP---> Dell 2716 --->dell 2650/ computers. I set the computers prefered dns to the servers ip. Im able to join the domain and log in but is there a better way to set it up. Also the server and computers are set to static ip.
View 2 Replies
ADVERTISEMENT
May 22, 2011
I recently purchased a used 2716, and I just can't seem to access the web interface.i have a Cat5e cable running from my router to Port 1 of the switch. I have my laptop connected to Port 16 via a Cat6 cable.
I have internet access both on managed and unmanaged modes, so that's working just fine. I can't seem to access the web interface however. I've tried both IE9 and FF4.
I followed the instructions to hold down the "Managed Mode" button for 30 seconds, and then wait for the switch to reboot. I've done this a few times just to be sure. This should reset it, but when I try to access 192.168.2.1, it just tells me it cannot access this page.
View 15 Replies
View Related
Feb 23, 2012
I have no previous Cisco switch experience. I just received a brand new SG200-08 switch. It replaces a small blue Trendnet 5 port switch. I configured the SG200-08 with a static IP address which is on the same subnet as all our wired devices, then I installed it and connected a computer and printer and another switch to it. The other switch is a Dell PowerConnect 2716. I suddenly have no network connectivity with the router any longer. When I plug the network cable that runs from the PowerConnect 2716 into the SG200-08, the link status light will not go on for that port. I am going to be replacing the Dell PowerConnect with a Cisco switch as well, the SG300-10.
View 6 Replies
View Related
Aug 17, 2011
I've tried to get my head around this but beeing used to Juniper and Watchguard devices I just can't get my home webserver published to the outside interface.I have a ASA5505 with ASA version 8.4 and ASDM version 6.4 and the basic license.
Outside interface is X.X.X.32/255.255.255.248 so I have 5 static IP:s on my external interface, .34 is in use for the outside interface.
Inside 10.10.10.0/25
DMZ 10.0.0.0/24
I have a webserver in DMZ located at 10.0.0.253 and would like to publish it to the external IP X.X.X.35.I've tried to make the static NAT but every time I do either nothing goes in or out of the DMZ zone or you can't access the webserver from the outside interface.Right now I deleted all trials since none of them work so only the basic config is applied. Everything get's NAT:ed to the external interface .34 IP.
View 4 Replies
View Related
Dec 18, 2012
I have the syntax correct and thought process down right on a solution to allowing guest wireless users access to an internal webserver. (DMZ discussion aside)
We have an ASA5510 with interfaces setup as:
outside - 65.x.x.x address
inside - 172.20.1.2
guest_inet - 10.2.1.1
Internally clients resolve our website to 192.168.40.40 and that part works as it should. Clients outside of our network resolve our website to the correct external address (lets just call it 1.1.1.1). We have a NAT statement static (inside, outside) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 and an ACL to permit tcp any host 1.1.1.1 eq www
Clients on our guest_int use an external DNS server and hence resolve our website to 1.1.1.1. However it seems traffic goes out and back in our outside interface and this connection never occurs.
What I'm wondering is the correct NAT statement / ACL to add that would allow our internal clients on the 10.2.1.x network to access our internal website. Would that be: static (inside,guest_inet) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 ? Since there is already an ACL permitting port 80 traffic to 1.1.1.1 we should be taken care of on the ACL side of things, right?
View 3 Replies
View Related
Oct 30, 2011
Having an issue getting my DMZ vlan working. Running my ASA5505 and i have configured e0/2 for DMZ w/ VLAN ID 3. Connected to my 2716 on port2.Inside e0/1 w/ VLAN ID 1. Connected to my 2716 on port1.
I am trying to get my DMZ Vlan to ports3&4 (LAG1) but when i assign the LAG group to PVID 3 i lose connectivity on VLAN1. I want to send both VLANs to that host because the teamed adaptor is used for Hyper-v Network Switch.
View 17 Replies
View Related
Feb 24, 2013
I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
View 5 Replies
View Related
Jul 14, 2011
I have a Dell PowerConnect 5448 and i had a separate VLAN setup for my iSCSI traffic. Now yesterday I was going to add a few more ports to this VLAN but when i went into the switch the VLAN was gone. I know it was configured and saved because a few weeks ago when I set it up, I went into the switch several times to adjust stuff. For some reason when it lost power it may have reverted back to default settings.
View 13 Replies
View Related
Jan 13, 2013
I have just purchased Dell PowerConnect 6224? how can i create two VLANs (vlan 10 - 192.168.10.x/24 & vlan 20 - 192.168.20.x/24) that can communicate with each other without setting servers/workstation network gateway point to the vlan ip address?
View 2 Replies
View Related
Nov 16, 2010
I managed on my own to figure out how to Telnet in, activate the web control panel, and then access that via the web. Now here is what I am trying to do, it is not that complicated. We have a FIOS connection with 5 IPS: FIOS comes in as Ethernet, without DHCP.
What I want to Assign to Ports on the Switch:
1) Uplink to FIOS
2) VOIP PBX
3) Point of Sale System
4) Internal Network
5) Public Wifi
6-8: Not in use
Each of the above 2-5 will have a router connected to the switch port, each is a separate segregated network, with its Own public IP.
I want to configure the switch to prioritize traffic in the following manner:
Port 2: VOIP: Always gets TOP priority, then Port 3: PoS (but not that important), then port 4: internal (less important), then port 5: public wifi (least important).
View 1 Replies
View Related
Feb 2, 2012
I need to compare a cisco ws-c2960s-24TS-s with a PowerConnect 6224, the scenario is to interconnect SAN ISCSI to 1G in RJ45.
View 1 Replies
View Related
Oct 1, 2012
configuring an ACL for a 857 Cisco router for web-server traffic. I've configured a NAT for the inside network and added ACL entries for port 80 access but dont seem to have any luck accessing the website remotely. I suspect there's an ACL rule blocking access.
Setup Internet === Router === Webserver
Router address: 10.0.10.1 Web-server address: 10.0.10.77IP from ISP address: XXX.XXX.XXX.XXX
(masked for security)
View 2 Replies
View Related
Sep 6, 2011
The remote office is connected to hq via site to site vpn. I have 1 static IP (on the remote site)that I use for the site to site. I need to publish a web server at the remote site. My question is can I use the same IP for VPN and web server publishing, I am having trouble getting the web server to publish
View 2 Replies
View Related
Oct 20, 2011
Here's the layout: Cable modem in the basement. Several devices in which I'd prefer a wired connection in the basement. Upstairs on the 1st and 2nd floor of the house are many devices in which wifi is fine or preferred.Here's the problem: As you might guess, wifi is weak upstairs and certainly on the patio and 2nd floor. I have an access point upstairs that I've experimented with but it is flaky.
View 1 Replies
View Related
Nov 10, 2011
How to install a wireless network in home environment?
View 6 Replies
View Related
Jan 14, 2012
I am a new student in networking, taking the CCNA courses, and now want to rewire my home. I currently have a cable modem and E2500 setup running my network. I want to get the modem and router out of my computer room and in the basement where the cable enters the house. I want to do this to clean up the computer room wiring a bit and to run line drops to different rooms in the house where the internet will be utilized.Currently there are two PC's, a laptop, a tablet, sometimes a phone, and an XBOX using the internet. I want to get my printer back up and running on the network but thats another story. Only one PC is currently hardwired. I would like to run two cables into the room with the PC and XBOX that are currently using wireless, at least two into the computer room for the PC and network printer, and one or two into the living room for the blue ray player and possibly an internet tv.
View 1 Replies
View Related
Sep 10, 2011
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies
View Related
Oct 28, 2012
I just purchased a SG300-10 switch and loaded the newest 1.27 firmware on it. Setup my VLANS and trunks but I have this weird issue. My setup:
I have the SG300-10 as my main switch and changed it over to L3 so it can be my main core in my small network. On port 1, vlan 200 is setup as my native PVID untagged and I have it set to trunk vlan's 210(LAN network), 220 (management vlan) tagged over to a Dell powerconnect 5224 24port switch. On port 1 of the Dell switch, I have it setup as a trunk there as well with the same setup (native PVID vlan set to 200 untagged, trunking 210 and 220 tagged).
View 12 Replies
View Related
Feb 25, 2013
I have a RV082 router that is currently in prod. I have a Dell Powerconnect 5424 switch that I'd like to use in place of the unmanaged switches I am currently using.
I have the switch configured with it's IP, subnet, gateway, etc. I can plug devices into it and communicate with no problems. However, when I attempt to plug in the router, nothign will communicate to or from the switch. The devices I plugged in will not talk to each outer, ping the switch, or the router. Also cannot ping to the switch from a device plugged into the router. If I unplug the router, comm opens back up.
View 1 Replies
View Related
Sep 23, 2012
I'm configuring a 2 PowerConnect in stack mode. I can't seem to resolve this error - Recieved Frame Check Sequence Errors.Both stacks are in the lastest firmware version 3.3.4.1. Physical connections are tight.
View 1 Replies
View Related
Dec 14, 2010
8 Port Gigabit Switch, HP 1810-8G, Netgear GS108Tv2 and Dell PowerConnect 2808, which one is better for LACP Link Aggregation?
The Netgear GS108Tv2 has more function than the other two, but I don't know the Netgear is stable or not?
View 5 Replies
View Related
Apr 12, 2012
I am running a webserver locally and I am unable to resolve it by domain name (e.g. mydomain.com) when I am inside my network. However, I am able to hit it internally (e.g. 192.168.0.10) just fine. When I try to access mydomain.com from inside my network it comes up with my Actiontec router's admin page on 192.168.1.1.Here is my configuration:Actiontec FIOS router 192.168.1.1 (connected to internet)DHCP disabled Netgear Router 192.168.1.2 is in the DMZHas cable running from Actiontec's LAN port to Netgear's WAN port[CODE]
View 7 Replies
View Related
Feb 17, 2013
I am running a websever on virtual machine on ubuntu .how can i forward all traffic coming to my ip to virtual machine which is 192.168.1.4 on my LAN.here are my configs.
OS - Windows 7
Router - DLink
Virtual machine network Setting - Bridged adapter.
View 19 Replies
View Related
Feb 28, 2013
I have my webserver (30.30.30.50) located at DMZ zone. The public IP of my webserver is (119.2.116.191). From outside i can ping my webserver using public IP thats fine.The issue out here is, if i want to ping my webserver using public IP from Internal LAN then i cannot ping but i can ping my webserver using private IP.I am using ASA5520. [code]
View 2 Replies
View Related
May 14, 2012
We're running three networks (inside, outside and dmz). Inside is 10.0.1.0/24, dmz is 10.0.2.0/24, outside is a static ip allocated by our ISP. We'd like to configure the following:All traffic from the outside to [static provider ip] on port 80 should go to 10.0.2.200 port 8080.
View 14 Replies
View Related
Apr 24, 2011
I have one webserver which open for public via http and https. The server sit behind Cisco ASA 5510. Today our webserver have been hacked by someone. The index.html has been replaced by hacker own index.html file. Is it anyway to detect who did (by IP) this? is my Cisco ASA can give any clue about it? How to prevent from this happening in Cisco ASA? FYI, my ASA only allow HTTP and HTTPS port from outside to internal. This ASA is solely dedicated to protect the webserver.
View 3 Replies
View Related
Mar 20, 2011
ASA 5510I'm trying to add a static NAT for to allow access to an internal webserver on my DMZ. I've added the config, however i'm still unable to get to it from the outside. I'm able to ping and browse the server from the LAN and I'm also able to ping the external interafce from the outside, but just unable to browse.I've turned on logging and the error I'm getting is "Inbound TCP connection denied...flags SYN on interface outside"
View 0 Replies
View Related
Dec 20, 2012
I have setup a webserver on my home PC and I have forwarded port 80 on my router to the IP adress of the PC that is running the web server. The web server is working great; I can get to my web pages from outside of my home by going to http://MyIpAddress/Anyway, the problem is with the Windows Media Player plugin I'm using. I want to embed 6GB MPEG-2 videos into my web pages. I have some videos on my PC and I want to be able to watch them remotely by connecting into my web page. It works fine when I'm at home; other PCs can connect and play the videos no problem. The problem is when I'm at work. When I'm at work, I go to my web page (via my IP address in a web browser) and the Media Player plugin says "Connecting" for a minute, then it says Ready, but the video will not play. I tried using a smaller, AVI file (680 MB) instead to see if the problem was streaming such a large file, but the video still would not play.Do I need to foward more ports on my router so that Windows Media Player can connect back and get the information it needs?
View 4 Replies
View Related
Oct 3, 2011
I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies
View Related
Sep 20, 2011
I'm currently in the process of buying the new property, which is in the build process and would like to put some cables across 3 floors, which would be connected to the router downstairs.
View 3 Replies
View Related
Mar 13, 2011
I have been having a bit of trouble with networking my two machines to share files and allow printing i have a win 7 laptop and a xp home desktop. I share a net connection via 02 wireless box both systems have wireless i have tried many things
View 8 Replies
View Related
Jul 23, 2011
I have a sg300-10 switch. i update the firmware with the last one. Things are complicated when i create 2 VLAN. ( really 1 VLAN cause the first is native ).So i have the first VLAN with the interface 192.168.1.254 ans the VLAN 2 wich IP is 192.168.2.254
I'm connected with my workstation ( ip : 192.168.1.2/24 with GW 192.168.1.254 ) and i try to ping a web server on VLAN 2 ( ip : 192.168.2.2/24 GW 192.168.2.254 )
Ping is OK ! But when i try to reach any ports of the webserver : Nothing.
View 11 Replies
View Related
Sep 14, 2011
I configurated ipsec remote vpn at catalyst 6500.
192.168.14.0/24-- my servers are assigned this subnet
vpn user:10.10.10.0/24
192.168.10.229 ---- webserver ip address
[code]...
View 3 Replies
View Related
