Cisco WAN :: 5510 To Add A Static Nat To Allow Access To Internal Webserver
Mar 20, 2011
ASA 5510I'm trying to add a static NAT for to allow access to an internal webserver on my DMZ. I've added the config, however i'm still unable to get to it from the outside. I'm able to ping and browse the server from the LAN and I'm also able to ping the external interafce from the outside, but just unable to browse.I've turned on logging and the error I'm getting is "Inbound TCP connection denied...flags SYN on interface outside"
View 0 Replies
ADVERTISEMENT
Dec 18, 2012
I have the syntax correct and thought process down right on a solution to allowing guest wireless users access to an internal webserver. (DMZ discussion aside)
We have an ASA5510 with interfaces setup as:
outside - 65.x.x.x address
inside - 172.20.1.2
guest_inet - 10.2.1.1
Internally clients resolve our website to 192.168.40.40 and that part works as it should. Clients outside of our network resolve our website to the correct external address (lets just call it 1.1.1.1). We have a NAT statement static (inside, outside) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 and an ACL to permit tcp any host 1.1.1.1 eq www
Clients on our guest_int use an external DNS server and hence resolve our website to 1.1.1.1. However it seems traffic goes out and back in our outside interface and this connection never occurs.
What I'm wondering is the correct NAT statement / ACL to add that would allow our internal clients on the 10.2.1.x network to access our internal website. Would that be: static (inside,guest_inet) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 ? Since there is already an ACL permitting port 80 traffic to 1.1.1.1 we should be taken care of on the ACL side of things, right?
View 3 Replies
View Related
Nov 22, 2011
I running site-to-site IPsec VPN in Cisco 2811 IOS 12.4 both site. Here I encounter a problem to access server on Site A from Site B
Site A having Leased Line connected to router with Public IP. I have done static mapping 1 web server to Public IP (NAT). This to allow external users to access the server via Public IP. At the same time, users at Site B would need to access to same server via Internal IP since they have Site-to-Site VPN established. But once I done Static Mapping (NAT), user at Site B unable to access the server at Site A using its internal IP. But external user can access server via Public IP. What went wrong here. Do i need to add extra command to get this done?
View 3 Replies
View Related
Apr 24, 2011
I have one webserver which open for public via http and https. The server sit behind Cisco ASA 5510. Today our webserver have been hacked by someone. The index.html has been replaced by hacker own index.html file. Is it anyway to detect who did (by IP) this? is my Cisco ASA can give any clue about it? How to prevent from this happening in Cisco ASA? FYI, my ASA only allow HTTP and HTTPS port from outside to internal. This ASA is solely dedicated to protect the webserver.
View 3 Replies
View Related
Mar 20, 2012
Currently i am having a scenario where i have setup RV042 and which is connected to Microsoft Forefront 2010. PPTP works fine only on rv042 subnet but i am not able to access the "internal" network of TMG.RV042 (172.16.1.1) ---> TMG [external] (172.16.1.2) ---> TMG [internal] (192.168.1.1) Is there any way through static route to access the TMG internal network through RV042 pptp server?
View 1 Replies
View Related
Sep 27, 2011
we have a ASA 5510 firewall and i have created remote vpn user who connects the internal network via vpn any connect after connecting i want him to only access his internal PC via rdp and not access other internal website or shared folders without connecting to the RDP however now he can access the internal website wihtout connecting to RDP?
View 3 Replies
View Related
May 9, 2012
Is it possible to configure remote access (IPSEC client) to force all traffic through the tunnel (no split tunnel) yet still limit the internal hosts that can be accessed?
I have been asked to provide remote access (via ASA5510) with the following requirements:
- the client should have unrestricted internet access via the ASA (the source address will appear to be the outside interface of the ASA)
- the client should have access to only two internal hosts (192.168.10.10 and 192.168.44.10)
Is there a way to limit access to those two internal hosts, while still providing secured internet access? The only way I can see is to use an access list on another device (for example our core switch).
View 1 Replies
View Related
Sep 19, 2011
I've got an ASA 5510 that has been working like a charm for some time now. Until now we've not had to nat any resources to the outside. I created network objects for an internal host and an external host. The internal host has to respond to requests on tcp/2001.
The internal host has no problem accessing the internet, but when I attempt to access the internal host from the outside, I get the following:
4 Sep 20 2011 16:20:33 fw_outside_ip 62678 outside_host 2001 Deny tcp src outside:outside_host_ip/62678 dst inside_host:inside_host_ip/2001 by access-group "outside_access_in" [0x0, 0x0]
When I try to use the packet tracer to simulate the outside traffic, I get the following
5 Sep 20 2011 16:17:41 inside_host 2001 Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:outside_host/1065 dst inside_int:inside_host/2001 denied due to NAT reverse path failure
I've got over my NAT statement and access rule and can't find anything wrong with either.
Here are the pertinent NAT and access rule...
static (inside_int,outside) tcp interface 2001 inside_host 2001 netmask 255.255.255.255
access-list outside_access_in extended permit tcp host outside_host host inside_host eq 2001
View 5 Replies
View Related
Sep 14, 2011
I configurated ipsec remote vpn at catalyst 6500.
192.168.14.0/24-- my servers are assigned this subnet
vpn user:10.10.10.0/24
192.168.10.229 ---- webserver ip address
[code]...
View 3 Replies
View Related
Sep 20, 2011
I have home network with my Linksys E-4200.
My HP Microserver (Ubuntu +Samba+Apache) is connected via LAN. I have notebook (Windows 7). To my server (FILE+WEB) I have access only when I connected via LAN cable. In windows 7 i see my server and have access to the files. Webserver works also properly: access with the name of the server in web browser.
But by WiFI connection, there is no access ! The server has the reserved local IP-address, like 192.168.1.200.
What should I do to solve it? By typing "192.168.1.200" i see the localhost page, but nothing more!
View 2 Replies
View Related
Mar 23, 2013
I have nated my 172.81.15.0 255.255.255.0 into my internal server 10.1.10.164 , i can ping the out side server but the internal server is not accessible from out side static (Database-Servers,interface-sms) 172.81.15.2 10.1.10.164 netmask 255.255.255.255icmp permit 172.81.15.0 255.255.255.0 interface-smsroute zemen-sms 172.81.15.0 255.255.255.0 10.131.199.201 1access-list Database-Servers-in extended permit tcp host 10.1.10.164 host 10.185.62.144 eq 9090access-list Database-Servers-in extended permit tcp host 10.1.10.164 host 10.185.62.144 eq wwwicmp permit host 10.185.62.144 interface-smsi can ping the out side server 10.185.62.144 with out a problem . from the server 10.185.62.144 i can ping untill 172.81.15.2 and it will not ping the natted server 10.1.10.164. as u seen the accesslist ping is permitted.
View 1 Replies
View Related
Mar 14, 2011
I have configured a L2L VPN on a Cisco 1841 ISR. I am statically NATing some of my internal hosts to IP addresses that are included in the encrypted traffic. Please note that not all of the internal hosts are being NATed. I am doing this to hid some of the real IP addresses on the inside network. I have confirmed that the VPN works, as well as the NATing of the VPN traffic. I have traditionally configured L2L VPNs on Cisco ASA 5500 series appliances, and this is my first attempt with the 1841 ISR. I just want other to take a look a see if I missed anything, or, could I have done some of the configuration more efficiently. All comments are welcome.
VPN-RTR-01#show runBuilding configuration...
Current configuration : 9316 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname VPN-RTR-01!boot-start-markerboot-end-marker!! card type command needed for slot/vwic-slot 0/0logging buffered 51200 warningsno logging consoleenable secret 5 xxxxxxxxxxxxxxxenable password 7 xxxxxxxxxxxxxxx!no aaa new-modelip cef!!!!no ip domain lookupip auth-proxy max-nodata-conns 3ip admission max-nodata-conns 3!!crypto pki trustpoint TP-self-signed-2010810276 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-2010810276 revocation-check none rsakeypair TP-self-signed-
[code]....
View 1 Replies
View Related
Mar 18, 2012
I have an ASA5510 running 8.2 code and I have over 200 static nats from the outside to the inside interface and that is how I expose our systems to the Internet. If this inside interface fails we also have a bypass interface that also terminates on the internal network but I am not sure how the nats will behave given they are statically mapped to the inside.
View 1 Replies
View Related
Feb 9, 2012
I have just purchased an ASA 5505 for my remote users to access our internal network. I have followed all the setup instructions I can find. I am able to establish a VPN connection using the Anyconnect client and can see some of my internal network. (Basically, only the subnet of the internal interface) However, I have several subnets inside my LAN which are routed by another switch inside my LAN. I have built in the correct static routes so that the ASA will send traffic to that intenal routing switch for any subnets not part of it's inside interface subnet. I can see and ping those subnets from the ASA itself but the AnyConnect clients cannot.
View 9 Replies
View Related
Dec 15, 2012
One of my internal servers requires it to be available to the internet I am having a hard time allowing it to be NATed through my Ciscc 2801 router. It seems as though im missing something small. From what I can gather it seems as though its as issue with ACL, but im not sure. I have ran the following command: ip nat inside source static tcp 192.168.5.1 ***WAN IP Address*** 8443 extendable Then I tried to add it to the ACL via this command: access-list 150 permit tcp any host ***WAN IP Address*** eq 8443
Here is a copy of my config.
IP 172.19.3.x
sub 255.255.255.128
GW 172.19.3.129
Ciscso 2801 Router
[code]....
View 5 Replies
View Related
May 21, 2011
I wanted to move to the cisco arena, and having a bugger of a time figuring out simple nat/pat rules combined with access lists. I've been reading Richard Deal's Cisco ASA configuration book, googling the heck out of this simple problem and can't see what I'm missing.
I have an ASA 5505 unlimited security plus license running 8.2(3) and a simple network, 192.168.0.x internal, 192.168.3.x dmz (not even touching that yet!) and outside I have a /29 subnet of addresses, 25 is the gateway, and 26-30 are my addresses.
I have simple dynamic nat set up on the .26 address to nat to 192.168.0.x. All I'm trying to do is port forward a simple tcp port I set for my linux server (192.168.0.2) on the inside, for arguement's sake, it's 2222 (it's not really). My outside vlan 50 is X.X.X.226 255.255.255.248 , can I make a static nat (inside,outside) x.x.x.226 192.168.0.2 netmask 255.255.255.255 ?
I tried using (inside,outside) x.x.x.230 192.168.0.2 netmask 255.255.255.255 and that didn't work either. Is it not possible to use two external addresses to hit the entire /24 range AND a single server?
My access rule for this nat is permit tcp any 192.168.0.2 eq 2222 (where I'm using 2222 for my ssh port). then I apply that access list to the access group interface "outside".
I thought the outside interface would do a proxy arp (since I do not have the sysopt noproxyarp command) for my 227,228,229, and 230 addresses where .226 is my internal nat for all my internal machines i.e. 192.168.0.1 -> x.x.x.226 . I had this working like a charm before with my fortinet, so I know I have systems listening.
View 3 Replies
View Related
Nov 21, 2012
I'm working on setting up a template configuration for the Cisco ASA 5505 device that we'll use to configure more routers for various client needs. One of the requirements requested of me is the following: Internal hosts assigned a DHCP address are blocked from the internet Internal hosts with a static IP are permitted access to internet All internal hosts can communicate regardless of state
Now, I'm fairly new to this and I'm certain my terminology isn't correct so googling the problem has been fruitless. I have followed basic configuration guides and have configured the device to hand out DHCP addresses to hosts plugged in ports 1-7. If I'm plugged in and specify my address manually in the OS I am blocked from any access so I can only assume there is an access policy or some rule preventing me from authenticating against the router despite having set up VLAN1 to be the entire class C subnet. What sort of steps would I need to do to configure this? New access lists. For the record, the dhcp addresses are in the range of 10.100.31.64-10.100.31.95. VPN users are assigned an address from 10.100.31.220-10.100.31.240 and there seems to be no issues with that configuraiton. I don't wish to constrain what addresses a user can use should they specify a static IP (10.100.31.5 should be just as valid as 10.100.31.100).
View 10 Replies
View Related
Dec 14, 2012
We just changed ISPs and now have a /29 routed subnet to be used on our ASA 5510 (8.4) instead of the one public ip we had before.There are a couple of PAT translations that were previously setup on the "interface" address which i now want to assign to a different ip address further in my subnet.
So i just changed this:
object network BMMM
nat (inside,outside) static interface service tcp smtp smtp
to:
object network BMMM
nat (inside,outside) static other.external.ip.in.subnet service tcp smtp smtp
And assumed that this would work,y it does not, and this leaves me unable to contact that machine from the outside.And shoud i also change my access-list?The relevant access-list rule is:access-list outside_in extended permit tcp any object BMMM eq smtp
View 5 Replies
View Related
Jun 11, 2013
I've been following most of the comments in regarding how to allow communication between two internal networks on a ASA5510 8.2.5 But I am still a little confused about to how to set my firewall. I made chages to it and still do not have the desired results.
I need to allow comunication between Interface 0/1 and Interface 0/2. See configuration file with fake or dummy ip address below.
ASA Version 8.2(5)
!
hostname ciscoasa
domain-name lxx.com
[Code].....
View 1 Replies
View Related
Nov 5, 2011
I am trying to setup a VPN tunnel between a Cisco ASA 5510 (Version 8.2(2)) and Sonicwall TZ200. I got tunnel up and going and I am able to ping the Cisco ASA internal IP from the Sonicwall LAN but nothing else works.
When I try to ping a host behind the Cisco ASA from the Sonicwall LAN I get the following message "Asymmetric NAT rules matched for forward and reverse flows;
[code]...
View 14 Replies
View Related
Apr 27, 2013
I have a doubt on how do nat 2 internal ip addresses to 1 public ip for FTP uses.
As I know Cisco ASA cannot use to nat 2 internal ips to 1 public ip as the ASA cannot read the host header. It there anyway to control it by using acl or network object group?
My current configuration for nat 1 internal ip to 1 public ip:
static (firewall-dmz,firewall-outside) tcp 210.19.xx.xx 21 172.16.101.11 21 netmask 255.255.255.255 dns
View 1 Replies
View Related
Sep 18, 2012
I've tried a bunch things but it didn't work, I'm about to gave up! :-/
I have the following scenario:
ASA5510 - v8.3(2)
Interfaces
ETH0/0 = outside = 189.xxx.xxx.129
ETH0/1 = inside = 10.xx.1.15
[Code]....
What should I do to get the SIP and 8080 port working on my Public IP, likewise just as access from my browse the http://189.xxx.xxx.129:8080 and get through directly to my internal server 10.xx.xx.61 ?
View 5 Replies
View Related
May 17, 2012
Having trouble with a couple items. First of all, should I be able to ping the inside interface of the ASA from all internal subnets assuming all of these subnets/vlans are directly connected to the same L3 switch? I can ping the ASA inside interface from our L3 switch, but I cannot ping the inside interface from a host on a different internal subnet. I have setup static routing on the ASA [
route inside 10.10.96.0 255.255.248.0 10.30.1.1 1]and verified that I can ping the host [10.10.96.212] from the ASA inside interface [10.30.1.5]. The inside interface is on the 10.30.1.x/24 subnet. My host is on the 10.10.96.x/21 subnet. From the ASA I can ping 10.10.96.212, but I cannot ping 10.30.1.5 from 10.10.96.212. I can however ping 10.30.1.1 from 10.10.96.212.
This leads to my next issue, which is trying to setup the ASA to work concurrently with our current firewall. I'm doing this in order to transition to the ASA. I'd much prefer to cutover inbound NAT a little at a time vs. doing it all at once. Our current firewall is setup at 10.30.1.2 and this is the default route on our L3 switch (0.0.0.0 0.0.0.0 10.30.1.2). So my question is, if I setup an inbound NAT to one of our web servers on the 10.10.96.x subnet, will I be able to get it to route back to the ASA as opposed to ending up in asymmetric routing **** since the default route points back to our other firewall?
View 2 Replies
View Related
Apr 16, 2013
I am having a problem getting my ASA to work properly. I attached a diagram for reference and most of the config is below. When I finally got it to route properly between 2 sub nets on the internal network, the NO NAT statement broke routing for the VPN Clients who rely on a NAT statement for the same sub net that is listed in NO NAT access list. I can get one of the 2 to work by replacing NAT statements but can't figure out a combination to allow routing for both the internal sub nets and the VPN clients to work.
It's been about 5 days of tweaking this thing just to get the internal routing to work correctly and when I finally did I broke VPN client access. To note, the VPN clients can still log in and get a session going, they just can't get anywhere once they are in. I also think there's a lot of stuff in this config that is not needed like a lot of the object groups, etc. but I am being very careful about removing anything. I took over support of this ASA after someone else put it in place and over this past weekend we moved it to a new building and new ISP and that is when I had to get it to route between sub nets. The main point of this move was to remove building 1's reliance on building 2 for Internet and outside email access in the event that building 2 is not available (it is close to water and this has happened more than once over the past year).
So that is why I can't go with the smartest option of just keeping the routes on the router in the other building. I also know the 1600s are ancient but they're all we have for now. I can provide those router configs also but they are VERY basic, all static routing. The IP for the Cisco router on the same sub net as the ASA is 192.168.42.254.
This is the statement that allows the routing to work between the 2 internal sub nets but breaks VPN clients: nat (INSIDE) 0 access-list NO NAT
This is the statement that allows the VPN clients to work but breaks the internal routing: nat (INSIDE) 0 access-list INSIDE_nat0_outbound
The rest of the config is below the diagram.
ASA Version 8.2(2)
host name Cisco asa
domain-name default.domain.invalid
enable password - encrypted
password - encrypted
names
dns-guard
[code]...
View 7 Replies
View Related
Feb 4, 2013
I have inherited an asa 5510 whit 4GE SSM module installed. The asa runs fine, but i can not use the 4GE SSM ports. Using ASDM or console i can get and configure the gigabitethernet1/x ports but i can not get traffic on it. The ping from the console to the ip address of the Gigabitethernet1/0 is successful. On switches or hubs connected to those ports i can not see the port's mac address. The two Internal-data0/0 and Internal-data1/0 are down and i can get they up. How to configure 4GE SSM or ASA internal-data ports.
View 8 Replies
View Related
Jan 19, 2013
Is it possible to perform static Nat's through an internal network?I have a ASA 5510 with a public outside interface (let’s call it 68.68.68.1), and I have an inside private IP address (192.168.1.2/24). The inside IP address leads to a 4900m with that interface being configured with a 192.168.1.1 (no switching). On the 4900 M I have several VLANs one of them is an internal DMZ of sorts. (192.168.2.0/24). Within this DMZ network are several Web servers which need to be associated a public IP address (68.68.68.x).
Every time I configure a static Nat to associating a public IP address with an internal IP address within the DMZ, packet Tracer on the ASA informs me that the packet gets dropped at the static Nat and I cannot figure out why this is so.Safe it to say my question still stands is it possible to Nat (68.68.68.222 to and 92.168.2.60) given the configuration above, and how would I go about configuring in such the manner above so that I acn apply static nat through the 192.168.1.0 network to reach the 192.168.2.0 network.
View 11 Replies
View Related
Sep 18, 2012
I have ASA 5510 and configured client VPN or Annyconnect VPN, when I connect to the ASA remotely using anyconnect I am able to get IP address as configued, from Internal network I can ping and RDP that anyconnect VPN desktop, but the problem is from the remote anyconnect VPN client I am unable to access internal network, when I use ASA packet tracer and check traffic from internal to anyconnect pool of addresses it gives result ok, but when i use packet tracer to check traffic on outside interface from anyconnect address pool to internal subnet it always gives the packet is dropped at WebVPN - SVC, and I can find any where related configuration for that.
View 5 Replies
View Related
Apr 22, 2012
I am tasked with transferring all clients from one subnet to the other. I figure the nicest way to do this is to temporarily have the subnets talk to each other in an endeavour to avoid as much downtime as possible. The two internal subnets are:
192.168.0.0/24
192.168.43.0/24 (the intended migration network)
I am beating my head against the desk here as I dont seem to be getting anywhere after the changes I have made. The current configuration is as such:
ASA Version 8.2(5)
!
hostname ciscoasa
domain-name *****
enable password ***** encrypted
passwd ***** encrypted
names
[code]......
Upgrading the firmware is not really an option?
View 3 Replies
View Related
Sep 25, 2012
I was just wondering if it's possible with an ASA 5510 to connect to the external IP address of an internal server from inside the network. I have already set up dns doctoring for dns lookups, and everything is working fine there. We have an application inside the network that tries to connect straight to the external Ip of another internal server. where to look in the ASDM 6.4?
View 2 Replies
View Related
May 12, 2012
I have an ASA 5510 configured 3 interface Internet_AAPT, Internal_Network and Server_Network. The server network works fine as is able to connect to the internet and services like port 80 work from the internet in. But from the Internal_Network can only get to the server network but not internet (6May 13 201214:17:4030201310.153.111.21253663199.47.216.14880Built outbound TCP connection 42508 for Internet_AAPT:199.47.216.148/80 (199.47.216.148/80) to Server_Network:10.153.111.212/53663 (10.153.111.212/53663). The weird thing in logs i see a connection being made but for some reason its referring to the Server_Network interface? below is my current config...
ASA Version 8.2(5)
!
hostname ASA01
domain-name names
name 10.153.11.184 QNAP
name 10.153.11.192 exc2010
name 10.153.11.133 zeacom
[code]....
View 10 Replies
View Related
May 26, 2011
I'm trying to figure out how to get two 5510 ASA's to establish a Site-to-Site VPN.The version with two static IP's is working perfectly and stable but I haven't figured out how to get a VPN running between a static and a dynamic IP
View 12 Replies
View Related
May 19, 2012
We have a site with two inbound circuits, one for internet and one for our MPLS. Each circuit is being terminated by a 2921 Router and matching ASA 5510 Firewall. For the internal network, the Internet ASA's inside interface (172.16.0.1) is the default gateway for all hosts. OSPF is the routing protocol between all the routers and ASA's and routing is working. In fact, ICMP is working as well. From an inside host (172.16.0.81), we can ping anything on the MPLS network. But when I try to use telnet (for example), the connection fails. If I add a route to 10.10.10.0 to the host, or re-configure the host to point to the MPLS ASA (172.16.0.254) as it's default gateway, connections will establish.
Both ASAs are running 8.4(3), and have the following commands:
same-security-traffic permit intra-interface
interface Ethernet0/0
nameif outside
[Code]....
And from the MPLS nodes, I can see a tcp request is made.
View 6 Replies
View Related
Jul 19, 2012
I have a 100mbps internet connection from my ISP but once the connection hits the ASA the download speed gets reduced to 15mbps. My network is setup as follows: ISP Modem ---- Edge Switch ----- ASA --- Internal Cisco Switches
If I plug my computer into an extra port on the Edge Switch I get speeds around 92mbps with normal traffic still going to the ASA. But when I plug into the ASA and internal switches I have speeds of 15mbps.
I have made sure that duplex/speed match on the links. I have done packet captures and within two minutes I do have several dup acks and retransmissions. The retransmissions don't seem to match the dup acks. (The retransmission is not for the dup ack requested so the dup ack keeps being resent)
The only interface error is on the inside interface which includes 700 overruns in a weeks worth of time.I am not using an IPS/IDS. I do have several vpns on it but was not going through a vpn tunnel. I am also using NAT.I am using an ASA 5510 8.2(1)
View 4 Replies
View Related
