Cisco Firewall :: ASA 5510 / Unable To Get Internal Networks Talking To Each Other
Apr 22, 2012
I am tasked with transferring all clients from one subnet to the other. I figure the nicest way to do this is to temporarily have the subnets talk to each other in an endeavour to avoid as much downtime as possible. The two internal subnets are:
192.168.0.0/24
192.168.43.0/24 (the intended migration network)
I am beating my head against the desk here as I dont seem to be getting anywhere after the changes I have made. The current configuration is as such:
ASA Version 8.2(5)
!
hostname ciscoasa
domain-name *****
enable password ***** encrypted
passwd ***** encrypted
names
[code]......
Upgrading the firmware is not really an option?
View 3 Replies
ADVERTISEMENT
Sep 18, 2012
I have ASA 5510 and configured client VPN or Annyconnect VPN, when I connect to the ASA remotely using anyconnect I am able to get IP address as configued, from Internal network I can ping and RDP that anyconnect VPN desktop, but the problem is from the remote anyconnect VPN client I am unable to access internal network, when I use ASA packet tracer and check traffic from internal to anyconnect pool of addresses it gives result ok, but when i use packet tracer to check traffic on outside interface from anyconnect address pool to internal subnet it always gives the packet is dropped at WebVPN - SVC, and I can find any where related configuration for that.
View 5 Replies
View Related
Apr 20, 2011
I have an ASA 5510 working in Routed mode for a company with the following networks. everything works fine as desired. Below are the interfaces, security and ip addresses .
Ethernet0/0 DC_SERVER security-level 100
ip address 172.16.11.12 255.255.255.0
Ethernet0/1 Branches security-level 50
[Code]....
View 1 Replies
View Related
May 9, 2012
I have configured a Remote access vpn on pix 525 with 7.2(4) code. After getting connected (with ip address assigned from the pool) i am not able to reach any of the internal networks. [code]
View 3 Replies
View Related
Feb 18, 2013
I am new to Cisco ASA and have been configuring my new firewall but one thing have been bothering. I cannot get internal networks and routing between them to work as I would like to. Goal is to set four networks and control access with ACL:s between those.
1. Outside
2. DMZ
3. ServerNet1
4. Inside
ASA version is 9.1 and i have been reading on two different ways on handling IP routing with this. NAT Exempt and not configuring NAT at all and letting normal IP routing to handle internal networks. No matter how I configure, with or without NAT I cannot get access from inside network to DMZ or from ServerNet1 to DMZ. Strange thing is that I can access services from DMZ to Inside and ServerNet1 if access list allows it. For instance DNS server is on Inside network and DMZ works great using it. [code]
View 13 Replies
View Related
Apr 26, 2011
We recently got a Cisco ASA 5510 Security Appliance and I have some general question.
We have 1 T1 internet connection, and we have 2 internal networks. These 2 internal networks currently hav access to the internet. I am having issues with the 2 internal networks being able to communicate with each other.
View 2 Replies
View Related
Nov 7, 2012
We recently changed locations and acquired a new circuit from our provider. They also connected our remote branch office to our main office through MPLS. Now, as I understand it, the branch office basically connects back to the main office through our providers network (MPLS). We have a new router at the branch office which has a gateway of 192.168.1.225. The clients in that office have IP's of 192.168.1.96 - 100, using the gateway of 192.168.1.225.
The main office network is 192.168.0.0 (Gateway of 192.168.0.1)
At this end (Main office), I also have a new Cisco 2900 provided by the ISP, with port 0/0 for the outside connection (connected to the 0 port on my ASA 5505). The ASA's port 1 obviously running into my network hub. The provider tells me that port 0/1 on the 2900 is or should be used to connect the branch office back to here and has an IP of 192.168.0.225, as that's how the provider provisioned it. So, I plug that into the ASA's Ethernet port 0/2. And I'm assuming they have a route setup either on the 2900 or the router in the branch office so that 192.168.1.225 can reach me here at 192.168.0.0.
There is already a static route setup on the ASA: (192.168.1.0 255.255.255.255 192.168.0.225 1). As soon as I plug in the cable, the IP phones at the branch office work, but they can't access the internet or any resources in the main office. My questions are:
1. Shouldn't I be able to just go straight from the 0/1 port on the Cisco 2900 to my hub. At first I was plugging right into the ASA, but I don't think I need to do that, why go from the branch office through my ASA to access resources and then back out the ASA for internet. If they're already coming from 192.168.1.225, through the MPLS network, then they should go right to my network and then back out the ASA.
2. They have to route through the ASA first, in which case, do I need to setup another VLAN for that branch network in conjunction with a static route? I can ping the router and hosts in the branch office through the ASA only!
Below is the running sanitized config:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(2) !hostname ciscoasadomain-name audiology.orgenable password ulzaQiFnKVzDwUmW encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.0.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 1.2.3.4 255.255.255.240 ospf cost 10!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!boot system disk0:/asa822-k8.binftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns server-group DefaultDNSdomain-name audiology.orgsame-security-traffic permit inter-interfacesame-security-traffic permit intra-interfaceaccess-list
[code]....
View 16 Replies
View Related
Aug 30, 2011
I'm usually not working with this product, but this is what I'm trying to do.I have 2 internal networks setup on our Cisco ASA 5505 firewall. (not done by me, I'm a new to this product)I'm trying to access a server on one network from a PC located on the other internal network. (preferable through the web gui)When I try "Packet Tracer" from interface "Trust4" it fails on the NAT phase.(Source ip: 10.0.4.99, Destination ip: 10.0.6.99)
When I check the NAT rule, it says:
Type Source Interface AddressDynamic any outside outside.
View 3 Replies
View Related
Dec 14, 2012
We just changed ISPs and now have a /29 routed subnet to be used on our ASA 5510 (8.4) instead of the one public ip we had before.There are a couple of PAT translations that were previously setup on the "interface" address which i now want to assign to a different ip address further in my subnet.
So i just changed this:
object network BMMM
nat (inside,outside) static interface service tcp smtp smtp
to:
object network BMMM
nat (inside,outside) static other.external.ip.in.subnet service tcp smtp smtp
And assumed that this would work,y it does not, and this leaves me unable to contact that machine from the outside.And shoud i also change my access-list?The relevant access-list rule is:access-list outside_in extended permit tcp any object BMMM eq smtp
View 5 Replies
View Related
Jun 11, 2013
I've been following most of the comments in regarding how to allow communication between two internal networks on a ASA5510 8.2.5 But I am still a little confused about to how to set my firewall. I made chages to it and still do not have the desired results.
I need to allow comunication between Interface 0/1 and Interface 0/2. See configuration file with fake or dummy ip address below.
ASA Version 8.2(5)
!
hostname ciscoasa
domain-name lxx.com
[Code].....
View 1 Replies
View Related
Sep 18, 2012
I've tried a bunch things but it didn't work, I'm about to gave up! :-/
I have the following scenario:
ASA5510 - v8.3(2)
Interfaces
ETH0/0 = outside = 189.xxx.xxx.129
ETH0/1 = inside = 10.xx.1.15
[Code]....
What should I do to get the SIP and 8080 port working on my Public IP, likewise just as access from my browse the http://189.xxx.xxx.129:8080 and get through directly to my internal server 10.xx.xx.61 ?
View 5 Replies
View Related
May 17, 2012
Having trouble with a couple items. First of all, should I be able to ping the inside interface of the ASA from all internal subnets assuming all of these subnets/vlans are directly connected to the same L3 switch? I can ping the ASA inside interface from our L3 switch, but I cannot ping the inside interface from a host on a different internal subnet. I have setup static routing on the ASA [
route inside 10.10.96.0 255.255.248.0 10.30.1.1 1]and verified that I can ping the host [10.10.96.212] from the ASA inside interface [10.30.1.5]. The inside interface is on the 10.30.1.x/24 subnet. My host is on the 10.10.96.x/21 subnet. From the ASA I can ping 10.10.96.212, but I cannot ping 10.30.1.5 from 10.10.96.212. I can however ping 10.30.1.1 from 10.10.96.212.
This leads to my next issue, which is trying to setup the ASA to work concurrently with our current firewall. I'm doing this in order to transition to the ASA. I'd much prefer to cutover inbound NAT a little at a time vs. doing it all at once. Our current firewall is setup at 10.30.1.2 and this is the default route on our L3 switch (0.0.0.0 0.0.0.0 10.30.1.2). So my question is, if I setup an inbound NAT to one of our web servers on the 10.10.96.x subnet, will I be able to get it to route back to the ASA as opposed to ending up in asymmetric routing **** since the default route points back to our other firewall?
View 2 Replies
View Related
Apr 16, 2013
I am having a problem getting my ASA to work properly. I attached a diagram for reference and most of the config is below. When I finally got it to route properly between 2 sub nets on the internal network, the NO NAT statement broke routing for the VPN Clients who rely on a NAT statement for the same sub net that is listed in NO NAT access list. I can get one of the 2 to work by replacing NAT statements but can't figure out a combination to allow routing for both the internal sub nets and the VPN clients to work.
It's been about 5 days of tweaking this thing just to get the internal routing to work correctly and when I finally did I broke VPN client access. To note, the VPN clients can still log in and get a session going, they just can't get anywhere once they are in. I also think there's a lot of stuff in this config that is not needed like a lot of the object groups, etc. but I am being very careful about removing anything. I took over support of this ASA after someone else put it in place and over this past weekend we moved it to a new building and new ISP and that is when I had to get it to route between sub nets. The main point of this move was to remove building 1's reliance on building 2 for Internet and outside email access in the event that building 2 is not available (it is close to water and this has happened more than once over the past year).
So that is why I can't go with the smartest option of just keeping the routes on the router in the other building. I also know the 1600s are ancient but they're all we have for now. I can provide those router configs also but they are VERY basic, all static routing. The IP for the Cisco router on the same sub net as the ASA is 192.168.42.254.
This is the statement that allows the routing to work between the 2 internal sub nets but breaks VPN clients: nat (INSIDE) 0 access-list NO NAT
This is the statement that allows the VPN clients to work but breaks the internal routing: nat (INSIDE) 0 access-list INSIDE_nat0_outbound
The rest of the config is below the diagram.
ASA Version 8.2(2)
host name Cisco asa
domain-name default.domain.invalid
enable password - encrypted
password - encrypted
names
dns-guard
[code]...
View 7 Replies
View Related
Feb 4, 2013
I have inherited an asa 5510 whit 4GE SSM module installed. The asa runs fine, but i can not use the 4GE SSM ports. Using ASDM or console i can get and configure the gigabitethernet1/x ports but i can not get traffic on it. The ping from the console to the ip address of the Gigabitethernet1/0 is successful. On switches or hubs connected to those ports i can not see the port's mac address. The two Internal-data0/0 and Internal-data1/0 are down and i can get they up. How to configure 4GE SSM or ASA internal-data ports.
View 8 Replies
View Related
Jan 19, 2013
Is it possible to perform static Nat's through an internal network?I have a ASA 5510 with a public outside interface (let’s call it 68.68.68.1), and I have an inside private IP address (192.168.1.2/24). The inside IP address leads to a 4900m with that interface being configured with a 192.168.1.1 (no switching). On the 4900 M I have several VLANs one of them is an internal DMZ of sorts. (192.168.2.0/24). Within this DMZ network are several Web servers which need to be associated a public IP address (68.68.68.x).
Every time I configure a static Nat to associating a public IP address with an internal IP address within the DMZ, packet Tracer on the ASA informs me that the packet gets dropped at the static Nat and I cannot figure out why this is so.Safe it to say my question still stands is it possible to Nat (68.68.68.222 to and 92.168.2.60) given the configuration above, and how would I go about configuring in such the manner above so that I acn apply static nat through the 192.168.1.0 network to reach the 192.168.2.0 network.
View 11 Replies
View Related
Sep 25, 2012
I was just wondering if it's possible with an ASA 5510 to connect to the external IP address of an internal server from inside the network. I have already set up dns doctoring for dns lookups, and everything is working fine there. We have an application inside the network that tries to connect straight to the external Ip of another internal server. where to look in the ASDM 6.4?
View 2 Replies
View Related
May 12, 2012
I have an ASA 5510 configured 3 interface Internet_AAPT, Internal_Network and Server_Network. The server network works fine as is able to connect to the internet and services like port 80 work from the internet in. But from the Internal_Network can only get to the server network but not internet (6May 13 201214:17:4030201310.153.111.21253663199.47.216.14880Built outbound TCP connection 42508 for Internet_AAPT:199.47.216.148/80 (199.47.216.148/80) to Server_Network:10.153.111.212/53663 (10.153.111.212/53663). The weird thing in logs i see a connection being made but for some reason its referring to the Server_Network interface? below is my current config...
ASA Version 8.2(5)
!
hostname ASA01
domain-name names
name 10.153.11.184 QNAP
name 10.153.11.192 exc2010
name 10.153.11.133 zeacom
[code]....
View 10 Replies
View Related
May 19, 2012
We have a site with two inbound circuits, one for internet and one for our MPLS. Each circuit is being terminated by a 2921 Router and matching ASA 5510 Firewall. For the internal network, the Internet ASA's inside interface (172.16.0.1) is the default gateway for all hosts. OSPF is the routing protocol between all the routers and ASA's and routing is working. In fact, ICMP is working as well. From an inside host (172.16.0.81), we can ping anything on the MPLS network. But when I try to use telnet (for example), the connection fails. If I add a route to 10.10.10.0 to the host, or re-configure the host to point to the MPLS ASA (172.16.0.254) as it's default gateway, connections will establish.
Both ASAs are running 8.4(3), and have the following commands:
same-security-traffic permit intra-interface
interface Ethernet0/0
nameif outside
[Code]....
And from the MPLS nodes, I can see a tcp request is made.
View 6 Replies
View Related
Dec 18, 2012
I have the syntax correct and thought process down right on a solution to allowing guest wireless users access to an internal webserver. (DMZ discussion aside)
We have an ASA5510 with interfaces setup as:
outside - 65.x.x.x address
inside - 172.20.1.2
guest_inet - 10.2.1.1
Internally clients resolve our website to 192.168.40.40 and that part works as it should. Clients outside of our network resolve our website to the correct external address (lets just call it 1.1.1.1). We have a NAT statement static (inside, outside) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 and an ACL to permit tcp any host 1.1.1.1 eq www
Clients on our guest_int use an external DNS server and hence resolve our website to 1.1.1.1. However it seems traffic goes out and back in our outside interface and this connection never occurs.
What I'm wondering is the correct NAT statement / ACL to add that would allow our internal clients on the 10.2.1.x network to access our internal website. Would that be: static (inside,guest_inet) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 ? Since there is already an ACL permitting port 80 traffic to 1.1.1.1 we should be taken care of on the ACL side of things, right?
View 3 Replies
View Related
Feb 20, 2012
I am working on replacing our Checkpoint Firewalls with ASA's, and am running into the following NAT problem. On some of our Checkpoints, there are external NAT's that are mapped to multiple internal hosts based on ports.Is there any way to translate that to the ASA? I'm not sure the ASA will let you have multiple internal hosts mapped to one external IP using static NATs. The main issue, is these are alarm panels that receive data from external hosts (the traffic is initiated externally on the Internet) so I can't use dynamic PAT with this.
View 1 Replies
View Related
Dec 5, 2012
Since the power failure two days ago, my -ASA stops forwarding traffic to internal servers, for no apparent reason. Packet trace shows all OK, packet capture buffer stays empty when I try to http into the mail server. The only way to get it working is to change the Outside Ip to the one used for mail, then to change it back. It will work OK for a few hours, then stop, with nothing obvious in the logs.
View 2 Replies
View Related
Mar 20, 2012
We have an inside interface, 192.168.10.0/23We have an outside interface, public ip...We have the ASA connected to 5 site to sites, this is working fine and through the internal interface can access all remote sites and vice vera. These are 192.168.20.0/24, 192.168.30.0/24, 192.168.40.0/24, 192.168.50.0/24 and 192.168.60.0/24,When a user connects via Cisco VPN Client they can see the inside network but can't talk to the remote networks connected, for instance 192.168.40.0/24... whereas an internal user can. I understand that the VPN client connection is seen as an outside connection, not an inside connection... but then I read [URL] and I am confused even more.
View 8 Replies
View Related
Mar 17, 2013
I have created a VPN connection for ASA 5512-X by using the wizards and nothing seems to be wrong on the wizards's config.I am able to connect to the network by using the VPN but unable to ping internal network.Below is my config for your reference:
Result of the command: "sh run"
: Saved
:
ASA Version 8.6(1)2
!
hostname FAA-ASA-1
enable password crzcsirI44h2BHoz encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code].....
View 6 Replies
View Related
Oct 10, 2012
I'm able to build my tunnel but unable to RDP nor ICMP back to the internal network.
VPN Client IP: 192.168.200.200
INTERNAL IP: 172.17.130.200
my configuration is below:
HOME-ASAFW02(config)# wr t: Saved:ASA Version 8.4(4)!hostname HOME-ASAFW02domain-name hsd1.nj.comcast.netenable password ViPq56cvd3SGvB08 encryptedpasswd 8bcozHCAwCqA5BmN encryptednames!interface Ethernet0/0description OUTSIDE-Connectionswitchport access vlan 2switchport protected!interface Ethernet0/1description INSIDE-Connectionswitchport protectedspeed 100duplex full!interface Ethernet0/2description WiFi-LinkSYSswitchport access vlan 3switchport protected!interface Ethernet0/3shutdown!interface Ethernet0/4shutdown!interface Ethernet0/5shutdown!interface Ethernet0/6shutdown!interface Ethernet0/7shutdown!interface Vlan1description INTERNAL-Networknameif insidesecurity-level 100ip address 172.17.130.129 255.255.255.128!interface Vlan2description OUTSIDE-Link-to-ISPnameif
[code]....
View 12 Replies
View Related
Feb 26, 2013
I have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 4.2.2.2 i dont get any reply.The runing config is below for ur ref :
HQ-ASA-01# show running-config
: Saved
:
[Code]......
View 9 Replies
View Related
Jul 29, 2012
I am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br Interface IP-Address OK? Method Status Protocol Ethernet0/0 x.x.x.x YES CONFIG up up Ethernet0/1 x.x.x.x YES CONFIG up up Ethernet0/2 unassigned YES unset administratively down down Internal-Control0/0 127.0.1.1 YES unset up up Internal-Data0/0 unassigned YES unset up up Management0/0 192.168.1.1 YES CONFIG up up
View 8 Replies
View Related
Jun 18, 2011
I have a cable modem, hub and two routers. One router is wireless and the computers on this router have an IP address of 10.1.x.x. The other is a wired router and the computers on this router have an IP address of 192.168.x.x. Computers on both networks have Internet access but can't talk to computers on the other router.What I'm wondering is instead of using 3 hardware devices (1 hub/2 routers), is there any router model that will allow me to setup two internal networks similar to what I have above. I just want to cut down on the equipment and power that I use with my current setup.
View 1 Replies
View Related
Jan 25, 2013
Site is not opening in any of my systems in the local network. but if i change ip to a real ip or if i use some other internet source like netsetter then it gets opened.
View 1 Replies
View Related
Dec 13, 2011
I follow the steps according to the basic settings provided by Cisco Support forum, but still failed to access the internet,
ASA5510# sh run: Saved:ASA Version 8.2(1)!hostname ASA5510domain-name xxx.comenable password passwd names!interface Ethernet0/0 nameif outside security-level 0 ip address x.x.x.x 255.255.255.248 ospf cost 10!interface Ethernet0/1 nameif inside security-level 100 ip address 10.161.9.14 255.255.255.0 ospf cost 10!interface Ethernet0/2 no nameif no security-level no ip address!interface Ethernet0/3 no nameif no security-level no ip address!interface(code)
View 9 Replies
View Related
Jan 17, 2013
A customer has a ASA 5505 with a remote access vpn. They are moving their internal network to a new scheme and would like users who come in on the vpn to access both the exisiting and new networks. Currently the can only access the exisiting. WHen users connect to the remote access vpn, the asa gives them an address of 192.168.199.x. The current internal network is 200.190.1.x and they would like to reach their new network of 10.120.110.x.
Below is the config:
:
ASA Version 8.2(5)
!
hostname ciscoasa
[Code].....
View 2 Replies
View Related
Aug 23, 2011
I have not worked with ASDM in a while. I have a 5510, with asdm-645.bin in the flash. The device runs version 8.4(2). I can download ASDM from the http interface of the firewall from the management interface. But I can not log in. I have used blank username and password, no username and enable password, blank username with enable password and a few other permutations. I then tried to connect to the asdm interface from inside also. But I can not connect. Needless to say, I have enabled http, and updated the http access-list. The only logging I have enabled is buffered. Is there any configuration that I am missing? Shall I cut and past the config?
View 4 Replies
View Related
Nov 12, 2012
when I try to run debugs on a pair of our firewalls. Error Message: ERROR: No memory for debug trace buffer. Debugs not available..Cisco ASA 5510 8.2(5)
View 1 Replies
View Related
Jun 15, 2011
I have an ASA 5510 and I can not configure fine.
My problem is that I have 10 public address connected to ASA and each public address is redirectioned to an internal IP address.
An of these public address is the ip address of mi ASA.
how to configure and access-list and an NAT, the others I will configure.
interface Ethernet0/0
description Interface_WAN_World-Ttrends
speed 100
duplex full
nameif outside(code)
View 59 Replies
View Related
