We recently got a Cisco ASA 5510 Security Appliance and I have some general question.
We have 1 T1 internet connection, and we have 2 internal networks. These 2 internal networks currently hav access to the internet. I am having issues with the 2 internal networks being able to communicate with each other.
I've got an ASA5510 with an IPS/IDS module. Because of a merger, I've got two 10.10.10.x networks (West and Central). I'd like all West traffic to be IPS checked before going into Central. Once it goes into Central, it's out of my hands. Can I set up NAT to accomplish this?
Again, the traffic flow would be from West (10.10.10.1) through the ASA/IPS, and then to Central (10.10.10.1).
Is this possible? If not, do I need another router?
I have an ASA5510 running 8.2 code and I have over 200 static nats from the outside to the inside interface and that is how I expose our systems to the Internet. If this inside interface fails we also have a bypass interface that also terminates on the internal network but I am not sure how the nats will behave given they are statically mapped to the inside.
View 1 Replies View RelatedI've a question about VPN IPSEC on ASA5510
In the LAN network , we use a DHCP on a Windows2003Server. Is it Possible to Configure the remote VPN Clients to use this DCHPserver throughout the VPN IPSEC and Assigned Automatically IP when the connection is done?
Cisco ASA 5510 directly facing the internet on E0/0 (1 Public IP only) with internal LAN on E0/1. Exchange 2010 OWA working fine with ACL and NAT rules configured.Problem:
•1. Cannot publish internal web servers to outside, have tried PAT.
•2. Have multiple web servers to publish with all on one protocol (HTTP) to a single public IP which I don’t know if it’s possible on a ASA.
•3.When SSL VPN is configured with Local user database, connecting from Anyconnect client gives a certificate error. Upon viewing the certificate it points to the internal mail server.
I am new to Cisco ASA and have been configuring my new firewall but one thing have been bothering. I cannot get internal networks and routing between them to work as I would like to. Goal is to set four networks and control access with ACL:s between those.
1. Outside
2. DMZ
3. ServerNet1
4. Inside
ASA version is 9.1 and i have been reading on two different ways on handling IP routing with this. NAT Exempt and not configuring NAT at all and letting normal IP routing to handle internal networks. No matter how I configure, with or without NAT I cannot get access from inside network to DMZ or from ServerNet1 to DMZ. Strange thing is that I can access services from DMZ to Inside and ServerNet1 if access list allows it. For instance DNS server is on Inside network and DMZ works great using it. [code]
We recently changed locations and acquired a new circuit from our provider. They also connected our remote branch office to our main office through MPLS. Now, as I understand it, the branch office basically connects back to the main office through our providers network (MPLS). We have a new router at the branch office which has a gateway of 192.168.1.225. The clients in that office have IP's of 192.168.1.96 - 100, using the gateway of 192.168.1.225.
The main office network is 192.168.0.0 (Gateway of 192.168.0.1)
At this end (Main office), I also have a new Cisco 2900 provided by the ISP, with port 0/0 for the outside connection (connected to the 0 port on my ASA 5505). The ASA's port 1 obviously running into my network hub. The provider tells me that port 0/1 on the 2900 is or should be used to connect the branch office back to here and has an IP of 192.168.0.225, as that's how the provider provisioned it. So, I plug that into the ASA's Ethernet port 0/2. And I'm assuming they have a route setup either on the 2900 or the router in the branch office so that 192.168.1.225 can reach me here at 192.168.0.0.
There is already a static route setup on the ASA: (192.168.1.0 255.255.255.255 192.168.0.225 1). As soon as I plug in the cable, the IP phones at the branch office work, but they can't access the internet or any resources in the main office. My questions are:
1. Shouldn't I be able to just go straight from the 0/1 port on the Cisco 2900 to my hub. At first I was plugging right into the ASA, but I don't think I need to do that, why go from the branch office through my ASA to access resources and then back out the ASA for internet. If they're already coming from 192.168.1.225, through the MPLS network, then they should go right to my network and then back out the ASA.
2. They have to route through the ASA first, in which case, do I need to setup another VLAN for that branch network in conjunction with a static route? I can ping the router and hosts in the branch office through the ASA only!
Below is the running sanitized config:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(2) !hostname ciscoasadomain-name audiology.orgenable password ulzaQiFnKVzDwUmW encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.0.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 1.2.3.4 255.255.255.240 ospf cost 10!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!boot system disk0:/asa822-k8.binftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns server-group DefaultDNSdomain-name audiology.orgsame-security-traffic permit inter-interfacesame-security-traffic permit intra-interfaceaccess-list
[code]....
Currently my ASA5510 has a 64MB internal flash. Does the ASA require a higher capacity flash for an IOS upgrade from 7.2(x) to 8.2(x)? The Cisco Release Notes does not state any internal flash requirement, but just wanted to double check.
View 2 Replies View RelatedI am currently managing an ASA5510 using ASDM through the management port but I would like to manage the ASA through the internal port.
My concern is that I thought I remembered reading someplace that if you setup an internal port for management that it can't be used for anything else. Is this correct?
I only configured one internal port and it is the path to my LAN. I would hate to configure the port for management only to find that I disconnected my firewall from my internal network in the process. Can I use my one and only configured internal port for both ASA management and route from my LAN thru the ASA firewall?
I currently have the management port set to 192.168.1.1 and my internal interface is 10.1.1.1. If I open ASDM and connect thru the management port and select Configuration/Device Management/Management Access/ASDM/HTTPS/Telnet/SSH
select "ADD"
select access type "ASDM/HTTPS"
select interface "internal"
IP Address "10.1.1.0"
Mask "255.255.255.0"
Will that give me access to ASA management thru my internal network but cripple my network access to the ASA?
I'm usually not working with this product, but this is what I'm trying to do.I have 2 internal networks setup on our Cisco ASA 5505 firewall. (not done by me, I'm a new to this product)I'm trying to access a server on one network from a PC located on the other internal network. (preferable through the web gui)When I try "Packet Tracer" from interface "Trust4" it fails on the NAT phase.(Source ip: 10.0.4.99, Destination ip: 10.0.6.99)
When I check the NAT rule, it says:
Type Source Interface AddressDynamic any outside outside.
I am tasked with transferring all clients from one subnet to the other. I figure the nicest way to do this is to temporarily have the subnets talk to each other in an endeavour to avoid as much downtime as possible. The two internal subnets are:
192.168.0.0/24
192.168.43.0/24 (the intended migration network)
I am beating my head against the desk here as I dont seem to be getting anywhere after the changes I have made. The current configuration is as such:
ASA Version 8.2(5)
!
hostname ciscoasa
domain-name *****
enable password ***** encrypted
passwd ***** encrypted
names
[code]......
Upgrading the firmware is not really an option?
I am using ASA5510 and i want to know if it is possible to redirect http traffic to an internal proxy software. I explain : PC from the LAN use a internal proxy in their IE browser but some other PC doesn't use it.They are directy connected to the Internet using the Public IP from the WAN interface ( via NAT). Can we redirected this HTTP Traffic from the WAN interface to the Proxy in the LAN ?
Http Traffic will be routed like that : PC -> WAN interface -> Proxy -> WAN interface -> Internet In fact,can we create a rule saying : All http traffic which doesn"t come from the IP Proxy must be redirected toward proxy.
I have an ASA5510 running version 8.2(5) I am having an issue with routing/natting from an internal network to the outside interface IP on port 443 which has a nat back in to another internal address. i works externally in from a public address. i also see log messages to do with IP Spoofing
View 1 Replies View RelatedCurrently a network consists of two subnets, one subnet is behind a ASA and the other behind a PIX, both connecting to the ISP's routers. If the PIX is retired, is it possible to create/consolidate the two networks protected by the ASA5510 with the default gateway being the ISP?
How can two private networks be protected by the ASA5510? One conceptual way is to create the VLANS on a layer 3 switch, on the "inside" interface of the ASA. In this senario what would the "inside" network's IP address? If the above is possible, how would natting occur?
Is there an efficient configuration to protect two networks protected by the 5510, other than creating a DMZ?
Is it possible to create two private networks with same level of security, 100 on a three network interface connections?
I have been assigned to find out the nature of the network's bandwidth utilazation. Is there a way to analyze traffic and breakdown the traffic on the ASA5510?
View 9 Replies View RelatedI have a cable modem, hub and two routers. One router is wireless and the computers on this router have an IP address of 10.1.x.x. The other is a wired router and the computers on this router have an IP address of 192.168.x.x. Computers on both networks have Internet access but can't talk to computers on the other router.What I'm wondering is instead of using 3 hardware devices (1 hub/2 routers), is there any router model that will allow me to setup two internal networks similar to what I have above. I just want to cut down on the equipment and power that I use with my current setup.
View 1 Replies View RelatedWe have gotten our anyconnect clients to connect to the VPN with no issues and verifying credentials with RADIUS. Remote users however cannot access internal resources through the VPN. I know I need to setup an NAT Exempt statement for my VPN Pool to the Internal Network,
View 5 Replies View RelatedWe have ASA5510s and I've configured an SSL VPN using AnyConnect.. The VPN address pool is 10.10.10.0/24 and our internal network is 10.10.20..0/24. After successful login, using LDAP. the client receives a 10.10.10.0/24 address from the pool, but cannot access anything on the internal 10.10.20.0/24 network. I've toyed with access lists and NAT exemption, but to no avail. What do I need to do?
View 8 Replies View RelatedI have configured a Remote access vpn on pix 525 with 7.2(4) code. After getting connected (with ip address assigned from the pool) i am not able to reach any of the internal networks. [code]
View 3 Replies View RelatedSite is not opening in any of my systems in the local network. but if i change ip to a real ip or if i use some other internet source like netsetter then it gets opened.
View 1 Replies View RelatedA customer has a ASA 5505 with a remote access vpn. They are moving their internal network to a new scheme and would like users who come in on the vpn to access both the exisiting and new networks. Currently the can only access the exisiting. WHen users connect to the remote access vpn, the asa gives them an address of 192.168.199.x. The current internal network is 200.190.1.x and they would like to reach their new network of 10.120.110.x.
Below is the config:
:
ASA Version 8.2(5)
!
hostname ciscoasa
[Code].....
I have an ASA 5510 configured 3 interface Internet_AAPT, Internal_Network and Server_Network. The server network works fine as is able to connect to the internet and services like port 80 work from the internet in. But from the Internal_Network can only get to the server network but not internet (6May 13 201214:17:4030201310.153.111.21253663199.47.216.14880Built outbound TCP connection 42508 for Internet_AAPT:199.47.216.148/80 (199.47.216.148/80) to Server_Network:10.153.111.212/53663 (10.153.111.212/53663). The weird thing in logs i see a connection being made but for some reason its referring to the Server_Network interface? below is my current config...
ASA Version 8.2(5)
!
hostname ASA01
domain-name names
name 10.153.11.184 QNAP
name 10.153.11.192 exc2010
name 10.153.11.133 zeacom
[code]....
I have ASA 5510 and configured client VPN or Annyconnect VPN, when I connect to the ASA remotely using anyconnect I am able to get IP address as configued, from Internal network I can ping and RDP that anyconnect VPN desktop, but the problem is from the remote anyconnect VPN client I am unable to access internal network, when I use ASA packet tracer and check traffic from internal to anyconnect pool of addresses it gives result ok, but when i use packet tracer to check traffic on outside interface from anyconnect address pool to internal subnet it always gives the packet is dropped at WebVPN - SVC, and I can find any where related configuration for that.
View 5 Replies View Relatedi just installed a pix515e ( ios ver 6.2) in my network. and the vpn users can connect to it from the internet successfully but they aren't able to connect to any of the internal resources. some other informaion: i configured nating between the internal network (10.0.0.0/24) and the internet and another static nat policy between an internal resource through another public ip address on outside interface. but right now i need to let the vpn clients to connect to my internal resources.
View 5 Replies View RelatedI have configured an ASA 5505 to connect a single internal network to internet, it is not working. I have attached the config
View 9 Replies View RelatedI have an @Remote appliance through Ricoh for our copiers. This appliance connects to their site to transfer meter readings and other information. This appliance can't connect to their site to transmit data. Ricoh is telling me the problem is on our firewill. I have assigned the Ricoh appliance a static IP address in our network. Our firewall is a Cisco ASA 5510. I don't have much expereince with logging on the ASA, so I'm not sure what "teardown dynamic TCP translation from inside" means. Is there something that is preventing this IP from contacting the Ricoh site? [code]
View 3 Replies View RelatedWe have an ASA5510 with the IPS ASA-SSM-10 module installed. All is working well except event notification. When sending a test email from the SSM IPS, we get the error "could not connect to SMTP host". The Exchange SMTP host does allow traffic from the IPS and ASA. I can ping to the SMTP host by IP and name. What am I missing here?
View 3 Replies View RelatedI'm configuring an asa device for web access: SSL VPN service. I can have a user authenticate for web session with their active directory domain credentials (username and password). Once their web session has started, moving to the "browse networks" feature for a share viewing requires them to authenticate once again - "authenitcation required". I'd like to configure the device so that authenticating to the windows file share will be attempted using the previously entered credentials.
View 2 Replies View RelatedI've cloned the configuration off one of my ASA5510's to another 5510 to use as a template for a new data center deploy. I have configured the new firewalls networks and rules, and of course changed the WAN IP config to its new setting.
I want to test the firewall in y office before I deploy it. How should I configure my Macbooks ethernet configuraiton to test the firewall?, as I have tried without success to connect to it.
Let's say that my WAN configuration is 134.5.169.98/255.255.255.224 with a static route of IP address 0.0.0.0, Netmask 0.0.0.0 and a gateway IP of 134.5.169.97.
I've tried setting the route to force all traffic through the interface (sudo route add 0.0.0.0/1 134.5.169.98), but that did not work either. A trace route to the external interface IP of the firewall (or the external IP of an expose server) get's a "no route to host" error.
I've tried many configurations and have not been able to access the internal servers/services/VPN at all.I've also tried with a cross over, and straight through cables.
What should I configure my macbooks network configuration as so I can connect directly to the WAN port to test external access to the internal servers/services and test the VPN client?
ASA 5510 have two model Bun-K9 and Sec-Bun-K9 from the datasheet find out difference Port related and Redundancy. My questions is : Have any major difference for Security service between two model ?
View 3 Replies View RelatedI am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
I have two ASA5510's set up in failover, and the secondary keeps crashing after doing the interface checks when bringing failover up. This only happens if I try to upgrade the image on the secondary to anything newer than 8.4.1 (I've tried with 8.4.1-11 and 8.4.2). The primary one run just fine with new images.
I don't have the exact error right now, as I need to do a screen capture from console. It's just a huge crash dump.Are there anything I might have missed during the upgrade? Should I cold-boot both the firewalls in the correct order?
i have a ASA5510 in the office, that already configured 3 context, namely, admin, user, server.in the server context, the last running config was not saved, and there was a power trip last friday night. 1 of the sub interface was affected, and i need to recreate that interface.I am getting the below error, it only allow me to do changes those pre-defined interface.how to I create extra sub interface?
View 3 Replies View Related