Router With Two Internal Networks
Jun 18, 2011
I have a cable modem, hub and two routers. One router is wireless and the computers on this router have an IP address of 10.1.x.x. The other is a wired router and the computers on this router have an IP address of 192.168.x.x. Computers on both networks have Internet access but can't talk to computers on the other router.What I'm wondering is instead of using 3 hardware devices (1 hub/2 routers), is there any router model that will allow me to setup two internal networks similar to what I have above. I just want to cut down on the equipment and power that I use with my current setup.
View 1 Replies
ADVERTISEMENT
Jan 25, 2013
Site is not opening in any of my systems in the local network. but if i change ip to a real ip or if i use some other internet source like netsetter then it gets opened.
View 1 Replies
View Related
May 9, 2012
I have configured a Remote access vpn on pix 525 with 7.2(4) code. After getting connected (with ip address assigned from the pool) i am not able to reach any of the internal networks. [code]
View 3 Replies
View Related
Feb 18, 2013
I am new to Cisco ASA and have been configuring my new firewall but one thing have been bothering. I cannot get internal networks and routing between them to work as I would like to. Goal is to set four networks and control access with ACL:s between those.
1. Outside
2. DMZ
3. ServerNet1
4. Inside
ASA version is 9.1 and i have been reading on two different ways on handling IP routing with this. NAT Exempt and not configuring NAT at all and letting normal IP routing to handle internal networks. No matter how I configure, with or without NAT I cannot get access from inside network to DMZ or from ServerNet1 to DMZ. Strange thing is that I can access services from DMZ to Inside and ServerNet1 if access list allows it. For instance DNS server is on Inside network and DMZ works great using it. [code]
View 13 Replies
View Related
Apr 26, 2011
We recently got a Cisco ASA 5510 Security Appliance and I have some general question.
We have 1 T1 internet connection, and we have 2 internal networks. These 2 internal networks currently hav access to the internet. I am having issues with the 2 internal networks being able to communicate with each other.
View 2 Replies
View Related
Nov 7, 2012
We recently changed locations and acquired a new circuit from our provider. They also connected our remote branch office to our main office through MPLS. Now, as I understand it, the branch office basically connects back to the main office through our providers network (MPLS). We have a new router at the branch office which has a gateway of 192.168.1.225. The clients in that office have IP's of 192.168.1.96 - 100, using the gateway of 192.168.1.225.
The main office network is 192.168.0.0 (Gateway of 192.168.0.1)
At this end (Main office), I also have a new Cisco 2900 provided by the ISP, with port 0/0 for the outside connection (connected to the 0 port on my ASA 5505). The ASA's port 1 obviously running into my network hub. The provider tells me that port 0/1 on the 2900 is or should be used to connect the branch office back to here and has an IP of 192.168.0.225, as that's how the provider provisioned it. So, I plug that into the ASA's Ethernet port 0/2. And I'm assuming they have a route setup either on the 2900 or the router in the branch office so that 192.168.1.225 can reach me here at 192.168.0.0.
There is already a static route setup on the ASA: (192.168.1.0 255.255.255.255 192.168.0.225 1). As soon as I plug in the cable, the IP phones at the branch office work, but they can't access the internet or any resources in the main office. My questions are:
1. Shouldn't I be able to just go straight from the 0/1 port on the Cisco 2900 to my hub. At first I was plugging right into the ASA, but I don't think I need to do that, why go from the branch office through my ASA to access resources and then back out the ASA for internet. If they're already coming from 192.168.1.225, through the MPLS network, then they should go right to my network and then back out the ASA.
2. They have to route through the ASA first, in which case, do I need to setup another VLAN for that branch network in conjunction with a static route? I can ping the router and hosts in the branch office through the ASA only!
Below is the running sanitized config:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(2) !hostname ciscoasadomain-name audiology.orgenable password ulzaQiFnKVzDwUmW encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.0.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 1.2.3.4 255.255.255.240 ospf cost 10!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!boot system disk0:/asa822-k8.binftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns server-group DefaultDNSdomain-name audiology.orgsame-security-traffic permit inter-interfacesame-security-traffic permit intra-interfaceaccess-list
[code]....
View 16 Replies
View Related
Jan 17, 2013
A customer has a ASA 5505 with a remote access vpn. They are moving their internal network to a new scheme and would like users who come in on the vpn to access both the exisiting and new networks. Currently the can only access the exisiting. WHen users connect to the remote access vpn, the asa gives them an address of 192.168.199.x. The current internal network is 200.190.1.x and they would like to reach their new network of 10.120.110.x.
Below is the config:
:
ASA Version 8.2(5)
!
hostname ciscoasa
[Code].....
View 2 Replies
View Related
Aug 30, 2011
I'm usually not working with this product, but this is what I'm trying to do.I have 2 internal networks setup on our Cisco ASA 5505 firewall. (not done by me, I'm a new to this product)I'm trying to access a server on one network from a PC located on the other internal network. (preferable through the web gui)When I try "Packet Tracer" from interface "Trust4" it fails on the NAT phase.(Source ip: 10.0.4.99, Destination ip: 10.0.6.99)
When I check the NAT rule, it says:
Type Source Interface AddressDynamic any outside outside.
View 3 Replies
View Related
Sep 18, 2012
I have ASA 5510 and configured client VPN or Annyconnect VPN, when I connect to the ASA remotely using anyconnect I am able to get IP address as configued, from Internal network I can ping and RDP that anyconnect VPN desktop, but the problem is from the remote anyconnect VPN client I am unable to access internal network, when I use ASA packet tracer and check traffic from internal to anyconnect pool of addresses it gives result ok, but when i use packet tracer to check traffic on outside interface from anyconnect address pool to internal subnet it always gives the packet is dropped at WebVPN - SVC, and I can find any where related configuration for that.
View 5 Replies
View Related
Apr 22, 2012
I am tasked with transferring all clients from one subnet to the other. I figure the nicest way to do this is to temporarily have the subnets talk to each other in an endeavour to avoid as much downtime as possible. The two internal subnets are:
192.168.0.0/24
192.168.43.0/24 (the intended migration network)
I am beating my head against the desk here as I dont seem to be getting anywhere after the changes I have made. The current configuration is as such:
ASA Version 8.2(5)
!
hostname ciscoasa
domain-name *****
enable password ***** encrypted
passwd ***** encrypted
names
[code]......
Upgrading the firmware is not really an option?
View 3 Replies
View Related
Jan 21, 2012
Using a command prompt, how do I discover the internal IP of an unused router, which I set to a custom value and forgot? The router is not currently in use for internet access. I would like to access the control panel of the router without resetting it.I attached my netbook to the router with an RJ45 cable and disabled the netbook's wireless adapter to avoid conflicts with my current network. Using an elevated command prompt, I did an "ipconfig /release", rebooted and ran "ipconfig /all", but the gateway entry is blank. An "arp -a" returns 169.254.190.120 as the only interface. A "netstat -a" returns 169.254.190.120:xx...'s, 127.0.0.1:xx...'s, and 0.0.0.0:xx...'s, but no router internal IP address.Is there a way discover the attached device without resetting?
View 1 Replies
View Related
Mar 24, 2013
I have a private minecraft server running off an old computer in my house. i recently had trouble, i was unable to connect. after some investigating, i found that my router changed the servers internal ip, and as a result i had to re-forward all the ports. a short while later, i rebooted the server, and its internal ip changed again. first is was 192.168.1.103, but then it went to .129, and now its .137. how can i stop it from doing this? ive never had this issue before. its a cisco linksis e2000
View 3 Replies
View Related
Mar 21, 2012
How to Configure Router to redirect all internal computers to redirect to a particular website..
View 1 Replies
View Related
May 11, 2012
I have two networks that are on two different IP ranges, sharing an ADSL internet router.I can make the two networks access the internet through a Windows 7 PC acting as a router with two NICs, but I cannot print to a shared network printer (build in NIC in the printer).This is how it looks.
ADSL router IP:
IP address: 10.10.10.253
Subnet Mask: 255.255.255.0
Network A computers:
IP range of: 10.10.10.XXX
Subnet Mask: 255.255.255.0
Default Gateway: 10.10.10.253
[code]....
Note: All the computers can access the internet just fine, it's only the one set of computers on IP range 172.16.0.XXX that cannot see the printer.All computers are Windows 7 32bit Professional.
View 2 Replies
View Related
Dec 14, 2012
*-my router is a sonicwall nsa 2400. (ip: 192.168.0.7)
*-my network adresse is : 192.168.0.X /255.255.255.0
*-all computers in my network are using stat ips (not my fault, and i can not change this fact).
Question: Can i add a new network range (not physical wires ) in this router expl 192.168.1./255.255.255.0 X with DHCP,and link it to 192.168.0.X so two computers in this differents networks range can talk to each others ?
View 3 Replies
View Related
Sep 23, 2012
I am hoping to have my internal data NOT sent via the router.I'm trying to figure out if data from the Windows PC to the Ubuntu PC goes via the N750 AND the router or just the N750.It should be noted that the N750 is set up as an access point with DHCP/NAT disabled. I have read that switches (and I assume this "access point") can store the MAC Addresses of computers to cut out the router, but I'm not sure how to make sure that that's happening.
View 2 Replies
View Related
Mar 10, 2012
I am converting from a Cisco Model 850 to a RV042, all is well so far but I cannot implement one feature I had on the old router.I want to do one to one nat from one internal ip to one external ip but I only want to use one tcp/ip port.The command to do this on the old cisco 850 was this:"ip nat inside source static tcp 192.168.1.181 80 75.xxx.xxx.181 80 extendable"Can this be done with the RV042?I can do one to one nat but it include all ports.
View 1 Replies
View Related
Dec 14, 2009
I just bought a Linksys 320N router to replace another competitors router. I am trying to connect to my VPN server from outside my network. I have the external ip to my network. I setup the new 320N router just like the old router. set dmz ip to internal ip of vpn server, set port forwarding to 1723, both, internal ip of vpn server, I have a way to test the vpn while i am inside my network. So, I can watch the VPN server log and see the request come into the server and it times out with the Linksys 320 N hooked up. If I have the old router hooked up, the vpn establishes a connection.
View 9 Replies
View Related
Oct 3, 2011
I am trying to configure my catalyst swtich as an internal router.
I want to route traffic between 4 different subnets.
192.168.200.0 /24
192.168.201.0 /24
192.168.202.0 /24
10.10.10.0 /24
View 27 Replies
View Related
Aug 31, 2011
I have an 891W with the internal AP. I want to update the AP's software but can't find anywhere to get it on Cisco's site. If I go to Download All, Routers, 800 series, 891W all I can choose is IOS, IOS ROMMON and upgrade to LWAPP. If I go to Wireless Wireless integrated service routers, 800 series, 891W I get IOS and IOS ROMMON.
View 1 Replies
View Related
Jan 16, 2012
I used the GRE tunnel site to site VPN with 2 cisco 1841 routers. Behind one of the router R1, I used cisco ASA 5510, now my vpn is connect between two routers, but from R2 other site cannot access to LAN behind the firewall. From R1, also cannot route to local network, from local network can access to R1, I think cause of NAT . So how to configure to route internal network from R1 & R2 with VPN.
View 5 Replies
View Related
Mar 10, 2012
I am really new to this and studiying so I know that I am doing something dumb. Anyway, I purchased an ASA 5505 and placed it between my Cable Modem and Cisco 3745 router. The outside interface on the ASA is dhcp, the inside interface is 192.168.100.1. The outside interface of the 3745 is 192.168.100.2 and the inside is 192.168.1.1. The VPN pool is 192.168.200.10 - 192.168.200.10.
Here's are the problems...
1. When I establish a VPN session to the ASA, I can ping and access any resources dierectly connected to the ASA's interfaces and on the ASA's internal 192.168.100.0 network. However, I cannot access any resources behind the 3745. I cannot even ping 192.168.1.1.
2. Although I believe that I sent up split-tunnel, I cannot U-Turn back to the internet once connected to the VPN.
View 11 Replies
View Related
Oct 28, 2011
I want to set up 2 separate network with one cable modem for my restaurant. we wants to provide WIFI access to its customers, but wants to keep their internal network separated.
View 2 Replies
View Related
Jul 29, 2011
D-Link, RangeBooster N, Dual Band Router.
I would like to set one network for surfing and another for gaming.
View 1 Replies
View Related
Feb 15, 2012
I am tryign to setup 2 networks for my company. I need 1 network for the first room and another network on the second room. Each room can't access another room's computer. I have setup 2 workgroups for each room but it seems that the workgroup can't setup passwords. Every computer is in the same subnet with static ip. They all connect to a switch -> router -> modem.
View 3 Replies
View Related
May 1, 2012
internet provided to whole building with connections in every room -> personal router in my room -> my PCs, Macs & printer, how to set up my computers so that they can share files with each other and print to my network printer, but without being susceptible to being accessed from other computers in the building? I have my own netgear router. But at the moment, my shared folders are accessible by everyone in the building, so is my printer If I set all the computers to automatically set ip by DHCP, they can access the net, but everyone in the building can access them (and my printer which requires a manual ip doesnt work). If I set all the computers to manual addresses (e.g. 192.168.1.14 ... 192.168.1.15 ... 192.168.1.16 etc.) they work with each other, the printer works, its secure, but I can't access the internet!Is there a way to for example have my own internal network with manual ip addresses, while also being able to connect to the net?
View 1 Replies
View Related
Sep 13, 2012
I had an Linksys WRT54GS and this wireless is connected to a switch in an internal enviroment but i want connect guest users without them see my internal network and can't access to any internal server....how can i configure this?
View 1 Replies
View Related
Apr 4, 2013
Lately, Ive been trying to change my router DNS to OpenDNS. Somehow, after changing it, I couldnt access the router page at 192.168.0.1, getting the error 500 message. I unplugged and plugged the router with no effect. Im using a dlinkddns.com dynamic IP, and have a few ports forwarded for my DVR. The router model is DIR 615. want to change the DNs for speed and filtering purposes.
View 4 Replies
View Related
Nov 30, 2011
I've just recently started to get this error, and I'm not sure why (I have no expierence with routers whatsoever). I have noticed, that whenever this happens though, that my NAT type for my xbox goes strict.
View 4 Replies
View Related
Oct 11, 2011
I have a problem with my router, WRT54G2. I was upgrading my firmware when my computer froze up, so I had to exit. Afterwards, I could not connect to the web based setup page anymore. I did a factory reset and installed it again with Network Magic and set up my wireless key. It is working now however, I cannot get into the web based setup page. Whenever i go to 192.168.1.1 and enter my info, it just says 500 Internal Server Error. I was always able to access this page, now I can't, so I assume it's not working because of the interrupted firmware update. I do alot of mac filtering and I limit the amount of IP addresses my router gives out so if anyone hacks my security key, they still won't be able to connect, so accessing my router setup page is important to me. I have reset (hold down reset button for 30 secs - 1 minute) the router many times and still nothing. I mean, the router still works. My brother and I can still connect with our laptops, I just can't get to the web based setup page.
View 7 Replies
View Related
Jan 16, 2012
I have a e4200 sitting behind a BT home hub 2. The home hub provides internet connection to the e4200, and the e4200 allows all devices to connect. I am able to ping internal IP addresses, but when I try to ping by device name it returns the external IP address. How can I view / amend the DNS table on the router?
View 9 Replies
View Related
Sep 20, 2012
I just moved from a Linksys wired router to the Cisco EA2700 wired/wireless router.I have three web servers on my network that serve up content via standard web URLs. For example, pretend www.domain.com pointed to the WAN side of my EA2700. Port forwarding routes port 80 traffic to the server, located on an internal, private IP (ie, 192.168.1.21).All works well when accessing these servers from outside my network (I checked this via my mobile broadband connection). But when I'm on a workstation internal to the same network as the servers, I cannot connect to the servers via the web URL. Of course, I can hit them via the IP or an internal-only DNS network entry. For example, when on 192.168.1.55 on a desktop machine, and I type the URL in the form www.domain.com, it just hangs and times out. I was able to do this on the old Linky router. Traffic should go stop at the router and be re-routed back internally to the port-forwarded server - but it does not.
I have to route properly via the web URL and not the internal DNS name or IP addy, as I am running virtual web servers on IIS on one of the servers.Is there a setting I failed to set on the EA2700?
View 6 Replies
View Related
Mar 4, 2012
Just bought first wireless router, when i insert CD and start setup, after a few seconds i get Error 301: internal error. i have rebooted and still no luck. I've tried going to 192.168.1.1, i got in one time but didn't understand half the stuff. now i can't go back into that page.
View 8 Replies
View Related
