Home Network :: Tracing If Internal Data Goes Through A Router
Sep 23, 2012
I am hoping to have my internal data NOT sent via the router.I'm trying to figure out if data from the Windows PC to the Ubuntu PC goes via the N750 AND the router or just the N750.It should be noted that the N750 is set up as an access point with DHCP/NAT disabled. I have read that switches (and I assume this "access point") can store the MAC Addresses of computers to cut out the router, but I'm not sure how to make sure that that's happening.
View 2 Replies
ADVERTISEMENT
Feb 13, 2011
I want to setup a DC++ HUB for sharing data within the university local network. We have addresses of the form 172.31.*.*. These addressed are accessible within the university bu non routable outside on the internet. My plan is to setup a local HUB for DC++ for sharing data within the university intranet. So even if internet is unavailable data can be exchanged through LAN. This HUB must not be accessable outsied the university network.how should I do this all..implementing network sharing other than DC++. My basic idea is that everybody can share their data and the data is searchable from one common interface( Web interface is better option, if possible). And data featching should prefferably be from many hosts, using multiple connections so that speed can be improved..
View 4 Replies
View Related
Jan 5, 2012
I have a client(C) and a server(S) nodes plus an intermediate node(I). Each node has a public IP. What I want to do is to transmit some data(whatever) from C to S but this data to go through I. So C ---> S will become C ----> I ----> S. I read something to create a tunnel(ip add tunnel) between C and I and add a route between them ? I tried different examples but did not work at all.
View 2 Replies
View Related
Mar 10, 2012
I should set up a network for a little enterprise.The requirements can be summarized as follows:
- All the "business" softwares have to be stored in a single computer (let's call it "the server"). The other computers (in this case there should be at most 2 or 3 computers) can execute these softwares through the server. So there are no local copies of those softwares on clients, only on the server.
- The main computer (the server) shares also a printer.
- All the computers in the network, are interconnected through a single wi-fi modem/router. Some of them are connected through the wi-fi interface and others through an ethernet cable.
the server, in order to perform some special procedures, has to connect to a special modem which connects it to a remote private network. In order to do so, the server disconnects from the local enterprise network because Windows does not allow me to stay connected to more than one network at the same time.The remote private network does not require to disconnect from any other network, it's just a constraint imposed by Windows.In the meantime, clients are not able to execute softwares anymore and cannot print anything.when the server is connected to the private network, it still needs to execute the "business" softwares.
Is it possible to keep the server connected to both the networks without denying the access to softwares, data and printers to anyone? If yes, how?If not, how can I design the topology of the network in order to share softwares and other data among all the computers (server and clients)? It's important that when the server connects to the private network every computer (including the server itself) can still access softwares, data and printers.
View 1 Replies
View Related
Jan 24, 2012
I plan on starting a high speed LAN for my Gaming LAN party's. We send 100's of GB of data over our LAN networking when we do this, so i need a good switch that can handle the stress of the massive data transfers. It needs to be a gigabit switch and at least 8 RJ45 ports.or is there a different one i should get all together? i cant spend a butt load. url...
View 3 Replies
View Related
Feb 4, 2013
I have inherited an asa 5510 whit 4GE SSM module installed. The asa runs fine, but i can not use the 4GE SSM ports. Using ASDM or console i can get and configure the gigabitethernet1/x ports but i can not get traffic on it. The ping from the console to the ip address of the Gigabitethernet1/0 is successful. On switches or hubs connected to those ports i can not see the port's mac address. The two Internal-data0/0 and Internal-data1/0 are down and i can get they up. How to configure 4GE SSM or ASA internal-data ports.
View 8 Replies
View Related
Jul 29, 2011
I also know that if i wanted to learn where a certain IP address was located, i could easily use one of many websites to find out. What I want to know is what each number of ones IP address means. Lets take a random ip - 72.28.456.98 (seriously, random numbers i just thought of) What do each number mean anyway? How is the computer located with each set of numbers? And is there a table or anything somewhere that shows what numbers belong with what geographical location?
View 5 Replies
View Related
May 5, 2012
we (educational institution)are attempting to trace an ip address for a STC USB stick. Actually, we have requested STC GSM provider to trace it. Reason being is, one or more of our teachers have sent an email harassing other staff. We wish to find out if STC has the techincal know how to get this info.
View 2 Replies
View Related
Nov 7, 2011
I have a specific website that i cannot reach. I can reach all other websites without any problems.I have read this URL and followed the same instructions.I made the tracert and here is what i got.
View 5 Replies
View Related
Feb 15, 2012
I'm trying to trace a host and I'm getting stuck at the port channel mac addresses. I need to find out where the server is connected to and the switch it lives on.
Please read below:
Step 1) Log into the core (MSFC): Code...
How do I find out where this physical server lives? I keep getting the mac for the trunk ports which is being used for all VLANs.
The server is hanging off some switch but I need to track it down to the last end.
View 1 Replies
View Related
May 1, 2012
internet provided to whole building with connections in every room -> personal router in my room -> my PCs, Macs & printer, how to set up my computers so that they can share files with each other and print to my network printer, but without being susceptible to being accessed from other computers in the building? I have my own netgear router. But at the moment, my shared folders are accessible by everyone in the building, so is my printer If I set all the computers to automatically set ip by DHCP, they can access the net, but everyone in the building can access them (and my printer which requires a manual ip doesnt work). If I set all the computers to manual addresses (e.g. 192.168.1.14 ... 192.168.1.15 ... 192.168.1.16 etc.) they work with each other, the printer works, its secure, but I can't access the internet!Is there a way to for example have my own internal network with manual ip addresses, while also being able to connect to the net?
View 1 Replies
View Related
Aug 9, 2012
I have an E3000 router, 2 computers connected via wires, and a PS3, airport express, laptop, and a few other devices which connect wirelessly. I've been having intermittent difficulties with specific services disappearing within my network. From time to time, some of the services which run across the network stop working; The Airport disappears (cannot contact it via airport utility or see it as an airplay destination), and the Playstation stops being able to contact media server running on wired computer. When this occurrs, all devices are still able to connect to the internet, and I am even able to copy files between a hard wired computer and laptop via CIFS (windows file sharing) protocol. Power cycling the E3000 solves this; the airport reappears, the PS3 can once again see the media server running on the PC, etc.
View 2 Replies
View Related
Feb 1, 2013
I am experiencing one, possibly two problems with the X3000, firmware release v1.0.03:
1. When enabling guest mode, the internal network is not accessible via WLAN even for clients NOT connected via guest mode but regularly: Even non-guests but regularly connected clients can't access any internal IP but the router itself. netscan shows only the very client's IP and the router's. Only after switching guest mode entirely off, regularly connected clients can access interal IP again. netscan correctly shows the whole network. Obviously a firmware bug. BTW: Clients connected via cable do not experience this problems.
2. I am not sure about this, but after using the firmware built in "Reboot" button, the router reboots correctly. But for some reason, it is instable afterwards. It is operational for a few seconds but then reboots again. It keeps cycling. I could stop it by switching the router off and on again.
View 6 Replies
View Related
Apr 27, 2011
I bought a DIR-655 for my parents after their old router died in a planned power outage. It's a rev. B1 model running the 2.00 firmware. It worked fine initially for a day or two with great wireless coverage, even in the previously low-signal spots in the house.Then the problems started. The router now has trouble loading any website. What you get is instead a page returned from the router saying something along the lines of "network unreachable, please check you internet settings" (I will go there today or tomorrow so I'll update the post with the specific error). Refreshing the page a few times sometimes makes it load, but extremely slow and then the same thing happens again a few moments later. The same thing happens on both wifi and through the router's LAN ports. If I connect a computer directly to the modem it works just fine, as it has always done before getting this router.I have disable QoS, NAT endpoint filtering and the firewall (SPI). I have also set the WAN port speed to 100Mbit/s in the router, to match what the modem is set to (also had issues with the default setting).
View 7 Replies
View Related
May 8, 2013
What is the best way to monitor an Internet Edge router from the Internal network behind the Firewall?We want to pull more information from the edge router like netflow. We can use SNMPv3 and ACLs to keep the router secure.
But I am looking for the best config to keep both the router and firewall as secure as possible while still allowing us to monitor performance and faults.I am running an ASA and a 2821.
View 2 Replies
View Related
Feb 24, 2013
I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
View 5 Replies
View Related
May 24, 2012
I have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
View 4 Replies
View Related
Oct 12, 2011
Hardware Software profile;
Laptop - Windows 7
Desktop - Vista Ultimate SP2
Router - Cisco Linksys E3200
Cables - CAT6
I am a sales engineer, so I use my desktop and laptop all the time. When on road, I sync my desktop with my laptop using a program called ViceVersa. This a very good, reliable syncing program that I have been using for over 10 years ( with upgrades ).
The program allows me to sync my desktop and laptop. The program also shows the data transfer rate during the syncing process. The typical data transfer speed is between 5MB/s and 10MB/s with sometimes up to 12MB/s. A typical sync between the computers will take about 3 - 5 minutes at the ~ 10 MB/s transfer rate using ethernet CAT6 cable inteface. At about 11pm last Tuesday,there was a Windows update on both my Vist and Win7 computers. On wednesday, I went to do a typical sync. The system has dramatically slowed to 59KB/s max. This is about 150 times slower than 5-10MB/s that I was used to for so many years. My typical sync was now taking about 2 hours....unacceptable ! I have tried everything to figure out what is going on and how to fix it but nothing has worked.
Then I tried to see what would happen if I disconnected my ethernet cable ( between the router and the laptop only ) and just sync using the wireless network. With that configuration, the transfer rate is ~ 2.5 MB/s which is not great but is much, much better than 59KB/s. I actually do not know what a reasonable wireless transfer rate should be since I never really did it before due to the faster speed of the wired configuration.
This is just a LAN. Only connecting my Desktop to my Laptop via the Cisco router.
How I can get my wired configuration back up to the 5-10MB/s transfer rate that it once was?
View 2 Replies
View Related
Mar 20, 2012
Currently i am having a scenario where i have setup RV042 and which is connected to Microsoft Forefront 2010. PPTP works fine only on rv042 subnet but i am not able to access the "internal" network of TMG.RV042 (172.16.1.1) ---> TMG [external] (172.16.1.2) ---> TMG [internal] (192.168.1.1) Is there any way through static route to access the TMG internal network through RV042 pptp server?
View 1 Replies
View Related
Oct 20, 2011
Here's the layout: Cable modem in the basement. Several devices in which I'd prefer a wired connection in the basement. Upstairs on the 1st and 2nd floor of the house are many devices in which wifi is fine or preferred.Here's the problem: As you might guess, wifi is weak upstairs and certainly on the patio and 2nd floor. I have an access point upstairs that I've experimented with but it is flaky.
View 1 Replies
View Related
Nov 10, 2011
How to install a wireless network in home environment?
View 6 Replies
View Related
Jan 14, 2012
I am a new student in networking, taking the CCNA courses, and now want to rewire my home. I currently have a cable modem and E2500 setup running my network. I want to get the modem and router out of my computer room and in the basement where the cable enters the house. I want to do this to clean up the computer room wiring a bit and to run line drops to different rooms in the house where the internet will be utilized.Currently there are two PC's, a laptop, a tablet, sometimes a phone, and an XBOX using the internet. I want to get my printer back up and running on the network but thats another story. Only one PC is currently hardwired. I would like to run two cables into the room with the PC and XBOX that are currently using wireless, at least two into the computer room for the PC and network printer, and one or two into the living room for the blue ray player and possibly an internet tv.
View 1 Replies
View Related
Sep 10, 2011
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies
View Related
Feb 28, 2012
My company have a Cisco PIX 525 firewall which is cater for NOC internal data network and also voice network, the subnet for data network is 192.168.2.0/24 and the subnet for voice network is 172.16.2.0/24. someday this NOC firewall was faulty. I was migrated the data network from this NOC firewall to the other temporary firewall just at the moment. And the voice network i migrated it from where it orginal at NOC firewall to a VOIP system which actually having a connection with my temporary firewall(This temporary FW only to take the traffic of data network). After the migration of data network from old firewall to temporary firewall and also the migration of voice network from old firewall to PABX system. The subnet for data network remain the same as 192.168.2.0/24, but the subnet of voice network i edit from 172.16.2.0/24 to 192.168. 3.0/24.Now when i want to use one Cisco router 2600 to replace this temporary firewall then facing problem at the voice network....The data network after migrated from temporary firewall to new 2600 is ok, users can browsing. But when i trying to at the same time when the data network been migrated , it will affect the voice network which still located at PABX. ..user cannot make call...I was thinking reason because this voice network which currently in 192.168.3.0/24 is tight to somewhere on the 192.168.x.x at the old firewall internetwork. So, when i migrated the data network over to new router, it will also cause the failure of voice even thought after i migrated the voice system to new router.So when i do the disaster recovery back to the temporary firewall for both data and voice. The voice is resuming to normal.
View 4 Replies
View Related
Dec 20, 2012
I have setup a webserver on my home PC and I have forwarded port 80 on my router to the IP adress of the PC that is running the web server. The web server is working great; I can get to my web pages from outside of my home by going to http://MyIpAddress/Anyway, the problem is with the Windows Media Player plugin I'm using. I want to embed 6GB MPEG-2 videos into my web pages. I have some videos on my PC and I want to be able to watch them remotely by connecting into my web page. It works fine when I'm at home; other PCs can connect and play the videos no problem. The problem is when I'm at work. When I'm at work, I go to my web page (via my IP address in a web browser) and the Media Player plugin says "Connecting" for a minute, then it says Ready, but the video will not play. I tried using a smaller, AVI file (680 MB) instead to see if the problem was streaming such a large file, but the video still would not play.Do I need to foward more ports on my router so that Windows Media Player can connect back and get the information it needs?
View 4 Replies
View Related
Oct 3, 2011
I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies
View Related
Sep 20, 2011
I'm currently in the process of buying the new property, which is in the build process and would like to put some cables across 3 floors, which would be connected to the router downstairs.
View 3 Replies
View Related
Mar 13, 2011
I have been having a bit of trouble with networking my two machines to share files and allow printing i have a win 7 laptop and a xp home desktop. I share a net connection via 02 wireless box both systems have wireless i have tried many things
View 8 Replies
View Related
Oct 17, 2011
Every time I connect to my home network with iPhone 4 my whole network stops working. Windows 7 is not reporting any problems with connection, nor is my router. I have cable connection with my PC and wireless with my laptop, they both just stop working without any visible reason. Even the iphone i connect with wont work, but of course it says its connected and everything is ok.I tought it was an iOS 5 problem, so I reinstalled it. It worked for an hour then its all back again. I even tried sharing my PC conection so that my iPhone is connected to PC and not directly to router.But that produced the same results.
View 6 Replies
View Related
Mar 9, 2013
My Set up at home is as follows: [code] Now according to what I have read I should be able to set the subnet on .2.0 network to a subnet of 254 and this gives me 512 Hosts I believe however my question at this point is how to route between 192.168.1.0 and 192.168.2.0.Or when I set the subnet .254 does the router just route it automatically.I would still set the subnet mask on both networks to 254 correct? I believe I can only use 192.168.0.1 to 192.168.1.255 w/.254 subnet mask. However I already have some servers that are configured with applications (On the 192.168.2.0 network) that I do not want to change ips on because it would be a pain to reconfigure so, my other question is other than using .252 to extend it to 192.168.0.1 to 192.168.3.255, (I need the 192.168.2.0) is there anything I can do? Like use 192.168.1.0 with subnet mask of 255.255.254.0 to get the 192.168.2.0 network? The reason I asked is I was using a subnet calculator to try and figure this out but every time I put in 192.168.1.0 with .254 subnet mask it changed the ip to 192.168.0.1 to 192. 168. 1. 255.I would really like to use the netgear only. The way I have it now is not working I am able to ping the internet from the 192.168.1.0 network but I can't ping from 192.168.2.0 network to the 192.168.1.0 network.
View 2 Replies
View Related
Jul 27, 2012
want to setup a small home network of about 10 PC's.I want them to share the internet connection of 25mbps.I also want Printer Sharing.
View 2 Replies
View Related
Jul 13, 2012
At the moment I have my home network (192.168.0.0/24) like as below (all connect using straight cables): [code] My Cisco lab equipment are in the basement all connecting to an access server which at the moment is plugged into Switch3-dumb (along with a printer & NAS).What I'm thinking is to replace the Switch3-dumb with a 3550 I'll be picking up later this week.Then using this to do as the Switch3-dumb did maybe by creating a native 'vlan 192' & putting it into a gig interface which will connect to the network using the straight cable, also putting the printer & NAS into the same vlan.This will hopefully still give me connectivity throughout.Then when required I'll like to use the 3550 with the rest of my Cisco equipment for setting up different labs (segmenting them from the home network by using different vlans etc.One of my reasons to implement the 3550 into the home network is to be able to play about on a regular basis (port monitor, traffic stats, etc).
View 2 Replies
View Related
Nov 24, 2011
My Wifi network has a wpa2 password that is a random string of characters and numbers and yet last month a rogue IP Address kept popping up on my DNS list. It has to be coming from my neighbor who's bedroom is about 15 feet away from my router. So unless someone is sitting out on my front lawn to do this then it must be him.I've been looking for software that will notify me when a connection my router is attempted and kudos if it also asks my permission first would be great.There are wifi packet sniffers out there like Cain&Abel, Airsnort, that sort of thing but I am not quite savvy enough nor do I want to turn this into a complicated hobby but just need a basic warningin case something gets past my passwords again
View 3 Replies
View Related
