I have just purchased Dell PowerConnect 6224? how can i create two VLANs (vlan 10 - 192.168.10.x/24 & vlan 20 - 192.168.20.x/24) that can communicate with each other without setting servers/workstation network gateway point to the vlan ip address?
View 2 RepliesI need to compare a cisco ws-c2960s-24TS-s with a PowerConnect 6224, the scenario is to interconnect SAN ISCSI to 1G in RJ45.
View 1 Replies View RelatedI am trying to manage my Dell switch that is trunked from my Cisco 2950, I have trunked vlan 251 (management vlan) and 252,configs below
Cisco 2950 :-
Current configuration : 4794 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code]....
I am trying the connection above using 10G spf connectors. Is there any special configuration in order to have a trunk (with 2 disctinct vlans) betwen NX7000 and DELL 6224 ?
View 14 Replies View RelatedI managed on my own to figure out how to Telnet in, activate the web control panel, and then access that via the web. Now here is what I am trying to do, it is not that complicated. We have a FIOS connection with 5 IPS: FIOS comes in as Ethernet, without DHCP.
What I want to Assign to Ports on the Switch:
1) Uplink to FIOS
2) VOIP PBX
3) Point of Sale System
4) Internal Network
5) Public Wifi
6-8: Not in use
Each of the above 2-5 will have a router connected to the switch port, each is a separate segregated network, with its Own public IP.
I want to configure the switch to prioritize traffic in the following manner:
Port 2: VOIP: Always gets TOP priority, then Port 3: PoS (but not that important), then port 4: internal (less important), then port 5: public wifi (least important).
I recently purchased a used 2716, and I just can't seem to access the web interface.i have a Cat5e cable running from my router to Port 1 of the switch. I have my laptop connected to Port 16 via a Cat6 cable.
I have internet access both on managed and unmanaged modes, so that's working just fine. I can't seem to access the web interface however. I've tried both IE9 and FF4.
I followed the instructions to hold down the "Managed Mode" button for 30 seconds, and then wait for the switch to reboot. I've done this a few times just to be sure. This should reset it, but when I try to access 192.168.2.1, it just tells me it cannot access this page.
I just purchased a SG300-10 switch and loaded the newest 1.27 firmware on it. Setup my VLANS and trunks but I have this weird issue. My setup:
I have the SG300-10 as my main switch and changed it over to L3 so it can be my main core in my small network. On port 1, vlan 200 is setup as my native PVID untagged and I have it set to trunk vlan's 210(LAN network), 220 (management vlan) tagged over to a Dell powerconnect 5224 24port switch. On port 1 of the Dell switch, I have it setup as a trunk there as well with the same setup (native PVID vlan set to 200 untagged, trunking 210 and 220 tagged).
I have no previous Cisco switch experience. I just received a brand new SG200-08 switch. It replaces a small blue Trendnet 5 port switch. I configured the SG200-08 with a static IP address which is on the same subnet as all our wired devices, then I installed it and connected a computer and printer and another switch to it. The other switch is a Dell PowerConnect 2716. I suddenly have no network connectivity with the router any longer. When I plug the network cable that runs from the PowerConnect 2716 into the SG200-08, the link status light will not go on for that port. I am going to be replacing the Dell PowerConnect with a Cisco switch as well, the SG300-10.
View 6 Replies View RelatedI have a RV082 router that is currently in prod. I have a Dell Powerconnect 5424 switch that I'd like to use in place of the unmanaged switches I am currently using.
I have the switch configured with it's IP, subnet, gateway, etc. I can plug devices into it and communicate with no problems. However, when I attempt to plug in the router, nothign will communicate to or from the switch. The devices I plugged in will not talk to each outer, ping the switch, or the router. Also cannot ping to the switch from a device plugged into the router. If I unplug the router, comm opens back up.
I'm configuring a 2 PowerConnect in stack mode. I can't seem to resolve this error - Recieved Frame Check Sequence Errors.Both stacks are in the lastest firmware version 3.3.4.1. Physical connections are tight.
View 1 Replies View RelatedI have problem with device cisco srp 521 , my problem is haw to create two VLAN-s first will be to WAN link, second for Management.
View 2 Replies View RelatedI need to be able to create vlans in my ASA 5510.
I can'T find anywhere to do this.
I've tried the "routers command" I know, like vlan databse and it does'nt work
Is there a way to "enable" vlan on a ASA 5510 ?
I just want create vlans on switch sge2010p
Scenario:
vlan10
ip address 192.168.10.254/24
vlan20
ipaddress 192.168.20.254/24
vlan10 needs internet.
I have a static ip internet which is 200.33.22.11 gateway: 200.33.22.10 I have a router configured working as gateway, It has ip 192.168.2.1.
I have configured two vlans. But when I try to check if vlan has internet, it doesn't work.
I need to set up a VLAN. We just bought the SG500x switches and we need to create several VLANs.
So for example:
192.168.1.x --> Vlan 1
192.168.2.x --> Vlan 2
192.168.3.x --> Vlan 3
What I would like to know is how do I come about setting this up and do I have to do something with my DHCP server to allow this to happen?
is there any specific way to create the SVI Interface on MSFC , actually I need to create the two SVI Int on MSFC to enable routing in between two VLANs on 7613 chassis.
View 2 Replies View Related I used two sf-300 switch and create 4 vlans and intervlan routing is working fine.
Port 1 - 10 -------------> Vlan 1
Port 2 -20----------------> Vlan 2
Port 3 - 30------------------> Vlan 3
Port 4 - 40--------------------> Vlan 4
giga1 -----------------> connected to router (This router used for intervlan routing).
SF-300 Port 1 is connected to Internet Modem. This modem worked as dhcp server also for vlan 1, my problem is that when vlan 1 is not communicate to vlan2,3,4 and 2,3,4 are not communicating.
How i can communicate vlan 1 to 2,3,4 vlan.
how i can connect the modem in switch? Access port or Trunk port ( Presently available in vlan 1 Access port)Any route i need to make? sf-300 or modem or router?
I am looking for a way to create different routing policies for vlans on a 3750 table.
My set up is
Clients----------- 3750 -------------- ASA ---------------Servers
|
|
|
Internet Routers
What i am trying to do is on the 3750 to route private networks to my ASA on different subintefaces and all internet to my internet routers . Each VLAN has a different GW for the internet. On some case i have the ASA as a default gateway. ASA default default route is 3750 where i need the internet traffic to be spllited on the proper Boarder router.
i want to create a trunk between 4507 & 3945E router & route two vlans from router 3945E
4507# vlan 99 & 51
# int vlan 99
# ip add 10.22.100.1/24
#int vlan 51
# ip add 10.22.103.1/24
[code].....
4507 version : IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
3945E: 15.1(2)T4 what I am missing?
I have a Dell PowerConnect 5448 and i had a separate VLAN setup for my iSCSI traffic. Now yesterday I was going to add a few more ports to this VLAN but when i went into the switch the VLAN was gone. I know it was configured and saved because a few weeks ago when I set it up, I went into the switch several times to adjust stuff. For some reason when it lost power it may have reverted back to default settings.
View 13 Replies View RelatedIm currently working on setting up a small network at home. I have a Dell 2716 and a dell 2650 server running windows server 2003. Ive already setup the dns and domain controller on my server. I have 3 desktops that will connect to the server. so far I have the following setup. ISP---> Dell 2716 --->dell 2650/ computers. I set the computers prefered dns to the servers ip. Im able to join the domain and log in but is there a better way to set it up. Also the server and computers are set to static ip.
View 2 Replies View RelatedI have 2 sub nets within my office: 172.16.1.0/24 and 172.16.2.0/24. All devices on each subnet are wired independently from each other into the server closet. Previously each sub net had it's own switch in the closet to connect to that sub nets servers. We are replacing the 2 switches with a single Dell 2816 managed switch.
Is there a benefit to setting up the switch with 2 VLANs over just letting everything pass through the switch in un managed mode?
My only security concern is this: 1 sub net has access to the internet while the other does not. Does setting up 2 VLANs provide additional security by preventing 1 subnet from accessing the other? In other words, if a computer with internet access gets hacked will it being on one side of a VLAN prevent the hacker from accessing the other subnet?
I have a power conncet 6224 with routing enabled with several VLANs setup.VLAN Database: 6,8,10,90-254VLAN 6 is our management vlan10 is for our core network services (DNS, Domain, Exchange etc)90-254 are isolated vlans.What I need to accomplish is to prevent vlans 90-254 from communicating with each other and only allow communication to VLAN 10 and the internet. All internet firewall work will be handled by our Sonicwall. [code]
View 1 Replies View Related8 Port Gigabit Switch, HP 1810-8G, Netgear GS108Tv2 and Dell PowerConnect 2808, which one is better for LACP Link Aggregation?
The Netgear GS108Tv2 has more function than the other two, but I don't know the Netgear is stable or not?
WE have to deploy ASA5585 in between User vlans & server vlans. we have to find all the ports that needs to be opened on firewall. any tools to do same.
View 2 Replies View RelatedI have a weird problem. I can't create a vpn in windows xp. I click on create a new connection, the connection wizard opens up, I click "connect to the network at my workplace", and this happens mm31z.jpg at Free Image Hosting.I can't select VPN connection. I have no idea what is causing this, maybe a service is not running, I don't know. I tried uninstalling/ reinstalling my network and it did not work.
View 5 Replies View RelatedI got my switch running as a router and several vlans running on it. My question is how do i tie the two vlans together so they can communicate? I know this might be a beginner question.
View 1 Replies View Relatedi want to build a website, but i don't have money
View 1 Replies View RelatedI am running windows 7 ultimate 32bit its been a long time that i've been trying to set a private server for call of duty 4 i've looked all over the web but no guide get my server online.i just read that i need to do something with ports etc(i dont even know what that is)
View 3 Replies View RelatedI wanted to have 3 vlan for my switch just for security reasons.(We do not want different Vlan members interact with each other)
I created 3 untagged Vlans on 48 port switch.
So ports 1-16 in Vlan 192.168.1.1/25
So ports 17-32 in Vlan 192.168.2.1/25
So ports 33-48 in Vlan 192.168.3.1/25
How to create a LAN using a modem
View 1 Replies View RelatedHow to create a new LAN Connection?
View 1 Replies View RelatedI got a pap for Xmas how do u create a connection in a psp
View 1 Replies View RelatedI have in one building a computer which has a real ip using and i want to connect to that building not via teamviewer or bomgar i wish to use VPN, how do i configure it? And why it is better using VPN?
View 2 Replies View Related