Cisco Switching/Routing :: Power Connect 6224 With Routing Enabled With Several VLAN Setup
Jan 19, 2013
I have a power conncet 6224 with routing enabled with several VLANs setup.VLAN Database: 6,8,10,90-254VLAN 6 is our management vlan10 is for our core network services (DNS, Domain, Exchange etc)90-254 are isolated vlans.What I need to accomplish is to prevent vlans 90-254 from communicating with each other and only allow communication to VLAN 10 and the internet. All internet firewall work will be handled by our Sonicwall. [code]
View 1 Replies
ADVERTISEMENT
Dec 13, 2011
I am trying the connection above using 10G spf connectors. Is there any special configuration in order to have a trunk (with 2 disctinct vlans) betwen NX7000 and DELL 6224 ?
View 14 Replies
View Related
Jan 3, 2012
I would like to apply a policy-based route on one of our L3 switches (Cisco 3750) to change the next-hop of a couple of servers only. The VLAN where those servers reside got WCCP enabled on it. When I want to apply the route-policy to that VLAN interface it doesn't let me. When I try to apply the same policy to a VLAN interface without WCCP it does work. Is there any Cisco IOS limitations that would prevent me from doing that?
Configuration:
route policy config:
access-list 70 permit ip host x.x.x.x (server IP)
route-map PBR1 permit 10
[Code].....
View 1 Replies
View Related
May 14, 2013
I'm trying to set up per vlan routing on a 3560G switch but it's not performing as I would expect. I've got a server on the 109 vlan with a 10.1.9.100 address and a default gateway of 10.1.9.1 this address is an HSRP gateway and currently resides on 10.1.9.7. When I traceroute through to my user PC on the internal network it receives a response from 10.1.9.7 However, it is then denied by an ACL on the internal firewall which has been applied to interface Eth0/0. It should arrive at the firewall on Eth0/2.109 as it has the 10.1.9.4 address.
My goal here is to route traffic on the 101 vlan to a seperate interface on the internal firewall from 109 vlan traffic. I'm either doing something wrong or these routing commands aren't designed to work in the way I'm expecting (I couldn't find any documentation on the ip route command where it is followed by different gateways for different vlans)
interface GigabitEthernet0/12
description Internal-FW Eth0/2
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 109
switchport mode trunk(Code )
View 1 Replies
View Related
Feb 19, 2013
I have a problem with the Cisco 881 router at one of our customers.It seems that after a "no shutdown" has been given on the Vlan interface, it still goes back to "administratevly down" after a reboot.So when I restart the router I always have to manually "no shutdown" the Vlan interface to come back up.While rebooting the router it also gives the following info in the console screen every time which is strange:
new interface Vlan1 placed in "shutdown" state.We tried several different firmware releases.
Replacing the router with a new Cisco 881 router did not work either. After they sent back the old Cisco 881 router we tested it here and there were no problems, we weren't able to replicate the problem.The configuration we use for the router is correct, we use it for hundreds of customers, so that can't be it either.The customer uses a fortinet firewall behind the router. Could it be that something inside the LAN of the customer that triggers the Vlan to shut down?
View 1 Replies
View Related
Nov 14, 2011
I am trying to set up VLAN on my cisco router, where do i check for the setting for creating a VLAN on my Wireless AP. Is it possible on this model.
View 1 Replies
View Related
Jan 30, 2012
I have a Cisco 3845 Integrated Service Router and I have installed a Service Module. I want to use the integrated Gigabit ports as switch ports and put ports in the Service Module and Gigabit port in a VLAN.
Is this possible? can it be done by setting internal Gigabit link as trunk and how? Below is the somewhat the setup i am looking for
Service module
fa0/1 |
fa0/2 | Vlan X
fa0/3 |
[Code]....
View 7 Replies
View Related
Jul 9, 2012
I have 2 SG300 switches, in layer3 mode, lag'd together for high availability, serving 2 Dell R815's and a Dell Equallogic 4100 for virtualisation. I have setup a number of vlan's, network traffic, mgmnt traffic, iScsi, vMotion etc and they seem to work.
However, Equallogic unit suddenly became unavailable to view for managment yet maintained iscsi traffic for the servers ok. After much head scratching, noticed that one of my SG300's had the vlan ports assigned to various vlans had *automagically* changed there assignment, ie tagged changed to excluded, but only for one of the iscsi traffic connections and the mgmnt port, both coming from the Equallogic, the other iscsi continued its assignment fine. The other SG300 hasn't changed. Guaranteee no one has been into change it and no changes have been made to Dell servers or Equallogic.
Q. Is there any circumstance where the switch can change the port setup itself? or is there any external circumstance that would trigger that change either?
This has now occured twice. The setup is running as a test lab, not in production until all setup is complete, then it will replace our existing harware.
View 1 Replies
View Related
Oct 25, 2011
I need to setup a vlan between the 6509 and 2621 router. This needs to be a VLAN (200) the runs between the devices that uses DOT1Q trunking. The end result is all the networks (vlans) on the 6509 can talk to the LAN on the 2600 (10.133.22.0 / 23) and visa versa.
Device 1
6509 with CatOS / IOS
Config I did on the MSFC:
Interface Vlan 200
ip address 10.10.10.1 255.255.255.248
[code]....
View 13 Replies
View Related
Dec 19, 2012
I am attempting to upgrade from a Cisco3945 to a ASR1002. On my Cisco3945, I have interface associated with VLANs. It appears that with the new IOSX, VLAN configuration has changed. Any config to setup a simple VLAN?
View 5 Replies
View Related
Nov 13, 2011
I am trying to setup a network using Cisco 2960 switches with vlans configured. One vlan will handle video coming from four cameras that are connected to another 2960.
We have four cameras feeeding one port each on a 2960, that 2960 in turn feeds one port on the main 2960 which is the video vlan for that site. From the site it goes back to a Cisco 3750 to be sent over to a Sonicwall firewall. If we connect to the 2960 that the camera are connected to we can see the video, but not on the main site 2960.
View 5 Replies
View Related
Feb 25, 2013
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
View 4 Replies
View Related
Jun 9, 2013
I am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
View 1 Replies
View Related
Sep 4, 2012
After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
View 5 Replies
View Related
Apr 14, 2013
We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
View 1 Replies
View Related
Feb 28, 2011
I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
View 3 Replies
View Related
Apr 4, 2012
In a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies
View Related
May 19, 2013
I am unable to connect a Wifi Modem wiith 2960 Switch having VLAN 1,Attached is the network diagram,what configurations i have to modified it,I need to Connect A Wifi Modem on VLAN 1 ,Connectivity is working fine between VLAN 10 and VLAN 1.What should be the next step to Connect Wifi Modem to VLAN 1 so that Users on VLAN 10 should connect to Internet.
View 14 Replies
View Related
Dec 9, 2012
Should I install any special license to enable vrf within Nexus 7000 VDC? I observed that vrf routing instance is not enabled in the VDC.
View 2 Replies
View Related
Oct 28, 2012
We have just received a new 3750X-12S-S to put onto our existing network but I am having a few issues getting this switch working correctly. For this post, the permenant license is not activating/applying, switch boot up gives the following errors:
*Mar 1 00:00:05.377: Read env variable - LICENSE_BOOT_LEVEL =
*Mar 1 00:00:05.972: %IOS_LICENSE_IMAGE_APPLICATION-3-FAILED: Image application receive image level as NULL.
[Code]....
From my understanding these switches come with the ipbase license as default, and the other switch I received (3750X-24P-S) has this license loaded with no issues.
View 3 Replies
View Related
Nov 12, 2011
Why I cannot ping vlan when no port connect to switch.
View 3 Replies
View Related
May 28, 2013
We have a setup of 2 Nexus 7000 chassis and several fexes (N2K-C2248TP-1GE). The fexes are connected through a port-channel to a single nexus 7000 (no vpc). (Fex 1 to Nexus 1, fex 2 to Nexus 2, fex 3 to nexus 1 etc).Are there guidelines on how to connect a server to those fexes.
I can see several possible scenario's at our site. I have drawn some scenario's on a design. I can't find detailed information on which setup is possible and which is not. The goal is to have as much redundancy as we can.When using scenario 1, do I configure an orphan port on the uplink to this server?
View 11 Replies
View Related
Mar 17, 2013
I have a customer who just bought a pair of N5K and wanted to replace his current HP E3800 as Core. He wants to use the 4 x stacked HP E3800 connect back to the N5K. Will I be able to utilize VPC through a bundled 2 or 4 x 10G (40G) connection (10 or 20G on 1 switch, and 10 or 20G on another switch) from the stacked HP E3800s to the N5548s? I know you can do that with Cisco 3750s.
View 1 Replies
View Related
Jan 30, 2012
Document at url... is quite interesting,One of these goes about the behavior of a switch (2960-S and 3750G) when QoS is not enabled vs the one when QoS is simply enabled with "mls qos".What additional commands, beside "mls qos", would be needed so as to simulate as accurately as possible the switch's behavior when QoS is not enabled?
View 3 Replies
View Related
Jun 21, 2010
I have installed NM-1T3/E3 IN A CISCO 3845 WITH IOS c3845-advipservicesk9-mz.124-9.T3.bin AND 512 MB RAM .WHEN I ENABLE THE CARD THE CPU PROC HISTORY SHOWS 100% WHEN DISABLED IT COMES DOWN TO 10%
Slot 0: C3845 Mother board 1GE(TX,SFP),1GE(TX), integrated VPN and 4W Port adapter, 7 ports Port adapter is analyzed
Slot 2: NM-1T3/E3 (clear/subrate) Port adapter, 1 port Port adapter is analyzed
View 6 Replies
View Related
Jun 3, 2012
I had problem with IP conflit address from cisco router 2911 , all the time the router respond with ARP reply (duplicate use of IP : x.y.z.t with the same Mac Address ) and the IP subject of conflit dosen't appear in any router's interfaces configuration (basic configuration without dhcp) ,the problem was solved problem when I desactivete proxy arp but I can't understand this behavior , why arp proxy respond to all IP address with same Mac even the IP dosen't exist in router ?
View 4 Replies
View Related
Nov 24, 2012
We are seeing output drops on a C3560 switchport, this port does not have QoS enabled -- application does not need special qos treatment, as long as packets are not droppd, so I suppose all traffic will share the same queue? then how should I read the output of "show platform port-asic stats drop" which indicates that it is queue 3 weight 2 drop? I am wondering what is the best way to fix this? enable mls QoS and increase queue 3 bandwidth share on this interface or just increase the output queue depth?
switch#sh mls qos interface gi0/1
GigabitEthernet0/1
QoS is disabled. When QoS is enabled, following settings will be applied
trust state: not trusted
[Code]......
View 8 Replies
View Related
Oct 3, 2012
I have enabled syslog on my Cisco 2960S swtich as shown below -
-logging facility local6
-logging host 10.11.12.122 transport tcp port 514
I have sent the port to TCP since that is what is configured on the SYSLOG server which is a CENTOS 5.8, running rsyslogd.I have tested the rsyslogd locally and it work.However i want to send any and all log messages in the buffer to my syslog server and it is not working.there is no firewall on the CENTOS and the ASA firewall filter is enabled for outgoing traffic.
View 5 Replies
View Related
Dec 21, 2011
Following procedures get to the switch: dir flash and get the following.....unable to stat flash//: no such device
View 4 Replies
View Related
Feb 16, 2012
Any "best practices" or recommendations on how to migrate from a fixed router (3745) to vlan routing on Catalyst 4507 switches in order to minimize the disruption to the network.
View 4 Replies
View Related
Oct 24, 2012
I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies
View Related
Oct 28, 2012
I have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies
View Related
Jul 24, 2007
Does Catalyst 3550 switch support inter vlan routing ?
View 12 Replies
View Related
