Cisco Switching/Routing :: IOS License Not Enabled In New 3750x-12s-s
Oct 28, 2012
We have just received a new 3750X-12S-S to put onto our existing network but I am having a few issues getting this switch working correctly. For this post, the permenant license is not activating/applying, switch boot up gives the following errors:
*Mar 1 00:00:05.377: Read env variable - LICENSE_BOOT_LEVEL =
*Mar 1 00:00:05.972: %IOS_LICENSE_IMAGE_APPLICATION-3-FAILED: Image application receive image level as NULL.
[Code]....
From my understanding these switches come with the ipbase license as default, and the other switch I received (3750X-24P-S) has this license loaded with no issues.
View 3 Replies
ADVERTISEMENT
Jan 16, 2013
Am attempting to load a new license on a 24 Port 3750X. Was LANBase code, need to get it to IPBase. Have the license file. Have put it on the flash drive. Running "license install flash:" i get the message "%Error reading flash: (is a directory)%Error: License installation failed with error: XML parsing failed"The license installation instructions are a bit cryptic so I could be messing it up. However, every variation I can think of is not working. The command listed above gets the most "promising" results.
View 1 Replies
View Related
Dec 8, 2012
I am having a ws-3750x-12s-s switch . I want to upgrade it from ipbase to ip service. after installing ip service liciense file, when i gave command " show license detail" i found there 3 index . one is for ip base -active (permanent) ..2nd is for ip service-active(permanent) 3rd is again ip service but inactive( period 8weeks 2days) , then i cleared 1st one by giving command "clear ipbase" and reboot. but still 2 index .both for ipservice one is permanent-active another is inactive . so my question is how can i remove 2nd index which one is inactive and time period for 8weeks and 2days..?? becasue i don't need it. and it will make any problem in future ?
View 2 Replies
View Related
Oct 7, 2012
I have two 3750x in a stack running c3750e-universalk9-mz.122-55.SE3.bin with License Level: ipservices?I am planning to upgrade to c3750e-universalk9-mz.122-58.SE2.bin will this keep my ipservices licence or revert back to IPbase
View 3 Replies
View Related
Dec 6, 2011
I recently added a 3750X-24P-L into a stack of 3750V2 switches. I did so by getting the temporary upgrade license from LAN Base to IP Services; I added the switch no problem. I now have the permanent license and I was wondering if I could install the permanent license without having to remove the switch from the stack. I tried a license install but that failed. The switch is not currently the master but I figured I might promote it and then try the install.
View 4 Replies
View Related
Jan 23, 2013
I have a Catalyst 3750X and 3750G configured in a stack. I need to break up the stack for failover reasons. My question is how do you determine what license's is on each of the switches. From the below print out. I assume the 3750X has the ip base license and the 3750G has the ipservices license. Is there a command that clearly shows which license's is installed on each switch in the stack? [code]
View 2 Replies
View Related
Mar 13, 2011
I'm trying to install a license file on a 3750x stack of 4 switches. I was running IPBase but want to upgrade to IPServices.
Install a License
3750E#copy tftp flash1:
3750E#172.x.x.x
3750E#FDO1111111_201101111111111.lic
3750E# license install flash1: FDO1111111_201101111111111.lic #
View 1 Replies
View Related
Jan 19, 2013
I have a power conncet 6224 with routing enabled with several VLANs setup.VLAN Database: 6,8,10,90-254VLAN 6 is our management vlan10 is for our core network services (DNS, Domain, Exchange etc)90-254 are isolated vlans.What I need to accomplish is to prevent vlans 90-254 from communicating with each other and only allow communication to VLAN 10 and the internet. All internet firewall work will be handled by our Sonicwall. [code]
View 1 Replies
View Related
Feb 25, 2013
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
View 4 Replies
View Related
Dec 9, 2012
Should I install any special license to enable vrf within Nexus 7000 VDC? I observed that vrf routing instance is not enabled in the VDC.
View 2 Replies
View Related
Mar 17, 2013
I have a customer who just bought a pair of N5K and wanted to replace his current HP E3800 as Core. He wants to use the 4 x stacked HP E3800 connect back to the N5K. Will I be able to utilize VPC through a bundled 2 or 4 x 10G (40G) connection (10 or 20G on 1 switch, and 10 or 20G on another switch) from the stacked HP E3800s to the N5548s? I know you can do that with Cisco 3750s.
View 1 Replies
View Related
Jan 30, 2012
Document at url... is quite interesting,One of these goes about the behavior of a switch (2960-S and 3750G) when QoS is not enabled vs the one when QoS is simply enabled with "mls qos".What additional commands, beside "mls qos", would be needed so as to simulate as accurately as possible the switch's behavior when QoS is not enabled?
View 3 Replies
View Related
Jun 21, 2010
I have installed NM-1T3/E3 IN A CISCO 3845 WITH IOS c3845-advipservicesk9-mz.124-9.T3.bin AND 512 MB RAM .WHEN I ENABLE THE CARD THE CPU PROC HISTORY SHOWS 100% WHEN DISABLED IT COMES DOWN TO 10%
Slot 0: C3845 Mother board 1GE(TX,SFP),1GE(TX), integrated VPN and 4W Port adapter, 7 ports Port adapter is analyzed
Slot 2: NM-1T3/E3 (clear/subrate) Port adapter, 1 port Port adapter is analyzed
View 6 Replies
View Related
Jun 3, 2012
I had problem with IP conflit address from cisco router 2911 , all the time the router respond with ARP reply (duplicate use of IP : x.y.z.t with the same Mac Address ) and the IP subject of conflit dosen't appear in any router's interfaces configuration (basic configuration without dhcp) ,the problem was solved problem when I desactivete proxy arp but I can't understand this behavior , why arp proxy respond to all IP address with same Mac even the IP dosen't exist in router ?
View 4 Replies
View Related
Nov 24, 2012
We are seeing output drops on a C3560 switchport, this port does not have QoS enabled -- application does not need special qos treatment, as long as packets are not droppd, so I suppose all traffic will share the same queue? then how should I read the output of "show platform port-asic stats drop" which indicates that it is queue 3 weight 2 drop? I am wondering what is the best way to fix this? enable mls QoS and increase queue 3 bandwidth share on this interface or just increase the output queue depth?
switch#sh mls qos interface gi0/1
GigabitEthernet0/1
QoS is disabled. When QoS is enabled, following settings will be applied
trust state: not trusted
[Code]......
View 8 Replies
View Related
Oct 3, 2012
I have enabled syslog on my Cisco 2960S swtich as shown below -
-logging facility local6
-logging host 10.11.12.122 transport tcp port 514
I have sent the port to TCP since that is what is configured on the SYSLOG server which is a CENTOS 5.8, running rsyslogd.I have tested the rsyslogd locally and it work.However i want to send any and all log messages in the buffer to my syslog server and it is not working.there is no firewall on the CENTOS and the ASA firewall filter is enabled for outgoing traffic.
View 5 Replies
View Related
Dec 21, 2011
Following procedures get to the switch: dir flash and get the following.....unable to stat flash//: no such device
View 4 Replies
View Related
Jan 3, 2012
I would like to apply a policy-based route on one of our L3 switches (Cisco 3750) to change the next-hop of a couple of servers only. The VLAN where those servers reside got WCCP enabled on it. When I want to apply the route-policy to that VLAN interface it doesn't let me. When I try to apply the same policy to a VLAN interface without WCCP it does work. Is there any Cisco IOS limitations that would prevent me from doing that?
Configuration:
route policy config:
access-list 70 permit ip host x.x.x.x (server IP)
route-map PBR1 permit 10
[Code].....
View 1 Replies
View Related
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Mar 6, 2013
i cant find any difference in these two devices when i am trying to compare throughput.I need upgrade our new POP and there will be around 4900 MAC adresses in VLAN 150 and 130 MAC adresses in vlan 200.Uplink is 1 gig routed internet connection and there is 14 downlinks to separate villages.i found a few differences for eg stack interface on 3750x but i dont need it.
View 2 Replies
View Related
Dec 27, 2012
I have a stack of 2 x 3750X switches these are running 12.2(55)SE5. I needed to add some static IP routes and found that the ‘ip routing’ command is not supported. I came across a document that stated “On switches running the LAN base feature, static routing on VLANs is supported only with Cisco IOS Release 12.2(58)SE and later.” So I have upgraded to 12.2(58)SE2, but ‘ip routing’ is still not a valid command.
The release notes state:“On the Cisco Catalyst 3560-X and 3750-X Series, it adds support for 16 static IPv4 routes in the LAN Base image.”
I have read other posts that talk about running the ‘sdm prefer routing’ command which I have done, but I am still unable to add any routes or run the ‘ip routing’ command.
View 4 Replies
View Related
Dec 9, 2012
I have an 1811 with several subnets connected to it.I recently installed a 3750x plant and want to bring my interior routing back to it.
All the routing is handled by the 1811 via secondary interfaces on vlan1?
I have 192 ports, and subnets show up on almost all of them. None of the ports are assigned to any specific vlans. Most ports have several subnets on them.
What is the best approach to getting the 3750x to handle the routing?
View 18 Replies
View Related
Nov 20, 2011
Is there a way to use the "no switchport command to enable routing on a port and yet sequester it from traffic on other vlans within the switch?
The switch in question is a 3750E
View 2 Replies
View Related
Feb 20, 2012
I have a Cisco Catalyst 2960 with IOS Release12.2(53)SE (because of a contract I can not update it) -> the release notes for this version describe the following:
When auto-QoS is enabled on the switch, priority queuing is not enabled. Instead, the switch uses shaped round robin (SRR) as the queuing mechanism. The auto-QoS feature is designed on each platform based on the feature set and hardware limitations, and the queuing mechanism supported on each platform might be different. There is no workaround. (CSCee22591)
My config is as follows:
interface FastEthernet0/1 switchport access vlan 200 switchport mode access srr-queue bandwidth share 10 10 60 20 priority-queue out mls qos trust dscp auto qos voip trust no cdp enable network-policy 1 spanning-tree portfastMy question now is:When the priority queue is not enabled with auto-qos because of the software bug is it nevertheless enabled with the additional priority-queue out command?
View 8 Replies
View Related
Nov 14, 2012
We have a 3750 acting as the core. By default IGMP snooping is enabled on cisco 3750 from the documents.but, when we see the ip mroute table on the switch, it doesnt show any output.
View 40 Replies
View Related
Feb 13, 2013
I have a customer that is seeing output drops on a 2960S with mls qos not enabled. It appears that they are getting bursts traffic on the switch that is filling up the buffers, hence causing the drops. I have a couple of questions:
1. What are the default queue/buffer settings when mls qos is NOT enabled on the switch.
2. Is there any good documentation out there regarding the buffer sizes of the different switch models
The customer is looking for an answer as to whether or not replacing the 2960S with a higher model would eliminate the output drops WITHOUT having to mess with QOS/buffer/drop threshold settings on the switch, and Cisco doesn't seem to make the buffer sizes readily available for the the smaller Catalyst switches.
View 1 Replies
View Related
May 22, 2013
my company pay a switch 3750 X. WS-C3750X-24T-E. It uses IP services basically but I failed to configure InterVLAN routing. why interVLAN routing doesn't work on my switch?
View 10 Replies
View Related
Nov 17, 2012
I was testing on 802.1x function on Catalyst 2950. the funtion itself work fine with my radius. but after I have setup the aaa new-model, I have no access to my switch!everytime I telnet it prompt me username, but I didn't create any user!!
how to recover to the origianl status, just prompt to input password but not username needed, and with 802.1x enable ofcause. [code]
View 10 Replies
View Related
Nov 3, 2011
I have a 2x Cisco 3750G switches (Stacked) that are part of an IP Video Surveillance System .All network is set to 1 VLAN (VLAN 1 default).The Cisco SWs ( Core ) are configured with IGMP Querier + Snooping .Connected to the Cisco SWs are 4 Fiber Rings(Loops) for redundancy . RSTP and IGMP Snooping are enabled on all the network SWs .Network Architecture Figure :
When all Fiber Rings (Loops ) are connected , the Cisco and Ring SWs spanning-tree tables show the blocked and forwarding ports properly .I am able to connect all my IP Cams + Encoders to the Ring SWs and connect my Servers + WorkStations to the Cisco SWs to record and view the multicast ip streams .All streams from Rings 1 ,3 and 4 are getting normally to the Servers + WorkStations through multicast ( IGMP Snooping are filled correctly on the Cisco and non-Cisco SWs ) . All multicast streams are joined normally except for Ring 2 .The Multicast streams passing through Ring 2 will operate normally for around 2 hours then after that the Fiber SWs begin to flood their multicast traffic causing the cams on the same switch to drop off the network .
I checked the Configuration of all the SWs on Ring 2 but all are are the same .
What is weird is that I have to set all the streams to unicast to stop the flooding just on Ring 2 (All other rings are not affected ) then after some time if I enabled a video multicast stream on one of the SWs of the Ring it will be streamed properly to the Servers + WorkStations ( All IGMP tables along the way will be filled properly ) then again after 2 hours or so , the flooding will start again suddenly and all IGMP table entries for the SW on Ring2 will be empty . No problem occurs on the other Rings which have more multicast streams .
View 0 Replies
View Related
Jan 24, 2013
I am setting up a vm environment for a customer in my lab off site. I have two stacked 3750-x switches, a san, and threes UCS c220 M3S servers for hosts. I am trying to separate the lan traffic, san iscsi traffic, and san management traffic using vlans. The problem is i'm unable to communicate cross vlan with my current config, which I have attached to this post. The only noteworthy things in my conifg is that the ip route 0.0.0.0 0.0.0.0 192.168.83.6 is referring to a switch stack they have on site, that I will connect this stack to using the first two trunk ports on each switch, that I do not have here in the lab. I don't want to cause any confusion in why I have things set a certain way.
View 1 Replies
View Related
Mar 28, 2012
Why does my 3750x-12s switch say it's not supported in CNA??? I upgraded to CNA 5.7.1 and still says unsupported. This device is supported or I'm just missing something.I use CNA heavily to manage our MANY vlans.
View 1 Replies
View Related
Mar 4, 2013
I want to confirm this is a licensing issue. On a 3750X with ipbase, I cannot create a vrf. So I would need the universal image, and that is a seperate license, correct?Is there a link that describes the difference bewteen ipbase and univeral images?
View 6 Replies
View Related
May 22, 2013
I have a query regarding attached Network Design
PC---2960---3750(One Routed Port and All Switched Port)------------------------ 3750(One Routed Port and All Switched Port)-----2960------Internet
I have many Vlans on left side of image , Right Side of Image is having internet connection via Modem, and local connectivity between VLAN works fine but Other Vlans Except Vlan1 is able to Access Internet.Note that 3750X did not have NAT Feature ,How should I able to get Internet on Other Vlans (10,20)
View 4 Replies
View Related
