I have a Catalyst 3750X and 3750G configured in a stack. I need to break up the stack for failover reasons. My question is how do you determine what license's is on each of the switches. From the below print out. I assume the 3750X has the ip base license and the 3750G has the ipservices license. Is there a command that clearly shows which license's is installed on each switch in the stack? [code]
View 2 RepliesI'm currently reconfiguring an ASA5510 installation to a HA setup with a second 5510. The old 5510 has an "AnyConnect for Mobile" license which isn't being used. So we upgrade that one to a SecPlus License to enable failover posibilities and we bought a new 5510 also with a SecPlus license. When I'm trying to enable failover I get the message that my mate hasn't got the "AnyConnect for Mobile" license. I know for failover both devices must be exactly the same (at first i thougth that the AnyConnect license would be lost when upgrading to SecPlus). So now I'm wondering and searching for solutions to remove the AnyConnect license (because we don't use it).
View 7 Replies View RelatedI have Asa 5510 with base license and no 3des free license installed on to it.Will it be required for both the licenses to be installed on it for site to site tunnels to establish.This firewall is not taking the below commands to give and the tunnel is not getting through.tunnel-group x.x.x.x type ipsec-l2ltunnel-group x.x.x.x ipsec-attributes.
View 3 Replies View RelatedI just upgrade a license on a cat 4510. The license installed but the EULA was not accepted and it will not upgrade to the new feature set.
View 1 Replies View RelatedWe have just received a new 3750X-12S-S to put onto our existing network but I am having a few issues getting this switch working correctly. For this post, the permenant license is not activating/applying, switch boot up gives the following errors:
*Mar 1 00:00:05.377: Read env variable - LICENSE_BOOT_LEVEL =
*Mar 1 00:00:05.972: %IOS_LICENSE_IMAGE_APPLICATION-3-FAILED: Image application receive image level as NULL.
[Code]....
From my understanding these switches come with the ipbase license as default, and the other switch I received (3750X-24P-S) has this license loaded with no issues.
Am attempting to load a new license on a 24 Port 3750X. Was LANBase code, need to get it to IPBase. Have the license file. Have put it on the flash drive. Running "license install flash:" i get the message "%Error reading flash: (is a directory)%Error: License installation failed with error: XML parsing failed"The license installation instructions are a bit cryptic so I could be messing it up. However, every variation I can think of is not working. The command listed above gets the most "promising" results.
View 1 Replies View RelatedI am having a ws-3750x-12s-s switch . I want to upgrade it from ipbase to ip service. after installing ip service liciense file, when i gave command " show license detail" i found there 3 index . one is for ip base -active (permanent) ..2nd is for ip service-active(permanent) 3rd is again ip service but inactive( period 8weeks 2days) , then i cleared 1st one by giving command "clear ipbase" and reboot. but still 2 index .both for ipservice one is permanent-active another is inactive . so my question is how can i remove 2nd index which one is inactive and time period for 8weeks and 2days..?? becasue i don't need it. and it will make any problem in future ?
View 2 Replies View RelatedI'm trying to install a license file on a 3750x stack of 4 switches. I was running IPBase but want to upgrade to IPServices.
Install a License
3750E#copy tftp flash1:
3750E#172.x.x.x
3750E#FDO1111111_201101111111111.lic
3750E# license install flash1: FDO1111111_201101111111111.lic #
I have two 3750x in a stack running c3750e-universalk9-mz.122-55.SE3.bin with License Level: ipservices?I am planning to upgrade to c3750e-universalk9-mz.122-58.SE2.bin will this keep my ipservices licence or revert back to IPbase
View 3 Replies View RelatedI recently added a 3750X-24P-L into a stack of 3750V2 switches. I did so by getting the temporary upgrade license from LAN Base to IP Services; I added the switch no problem. I now have the permanent license and I was wondering if I could install the permanent license without having to remove the switch from the stack. I tried a license install but that failed. The switch is not currently the master but I figured I might promote it and then try the install.
View 4 Replies View RelatedI installed windows XP and now I connect a cable from the router to the pc and I can't connect to the network.
View 1 Replies View RelatedI have 2 linksys routers installed on my home network. The primary router is a linksys WRT360n and is stationed inside the main home, while the 2nd is a linksys WRT160N located in my office. I've connected them via the lan to lan configuration and have disabled DHCP server on the 2nd. I can access the 2nd router via my primary PC but am unable to access the internet or see the primary from the PC connected to the 2nd router.
View 3 Replies View RelatedI have FSWM active/standby installed in 6509-E core switches running following FWSM Firewall Version 3.1(3) Device Manager Version 5.0(2)F..I want to upgrade to latest FWSM version as well as ASDM, I downloaded asdm-622f.bin and c6svc-fwm-k9.4-1-5.bin from cisco portal. When i checked the show version of FWSM, it says..The Running Activation Key is not valid, using default settings: Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000
I have gone through threads on CSC about how to upgrade FWSM in failover mode, now my concern is, Do i have to take care about activation key or keep as it is ? I have maintenance contract with cisco for all devices.
Recently, we had a 3750X stack of 9 switches reload with no information as to why. Our syslog server received no spurious errors regarding the cause nor did the location lose power. The UPS to which it is attached logged no glitches relating to power. Other cisco devices (router, other switches not in the stack) did not reload. No one was in the MDF during this time. We self insure these line of switches so a TAC case is not an option at this time. Any forensic tools that I could try in an attempt to narrow down the cause.
View 5 Replies View RelatedCan I implement MACsec betwen two Cisoc 3750X using the C3KX-NM-1G? 3750x (C3KX-NM-1G) -------------------MMF------------------(C3KX-NM-1G) 3750x.
View 1 Replies View RelatedAt our site we have a 4510 core switch and 3750x switches in our IDFs. The 3750 switches are connected to the core via DOT1Q trunks in a server client setup. We are putting in an Informacast/Berbee server witch will send pages and text to the cisco phones. We also have 1 3750 switch connecting to the core via a layer 3 port channel. If we put the Informacast server on the phones vlan would I just need to enable ip pim sparse-dense mode on that vlan only and enable multicast routing, ip multicast routing?
View 5 Replies View RelatedHow to get vlans working properly between sub-interfaces on a ASA and a trunk port on a switch.There seems to be issue with the VLAN's being assigned to the correct VLAN and this information being properly sent to the ASA over the trunk.
We seem to be unable to ping most of the interfaces except for one on the switch. Sometimes if we are lucky we are able to ping a host on a different vlan that is on the switch. This seems sparadic at best.
Logs on the ASA show traffic does not seem to be assigned properly to the correct sub interface. We have access rules on the ASA disallowing traffic not part of the same vlan. For example you will see networkA blocked on networkB when it really should be directed through networkA's sub interface.
Any example commands for the ASA and Switch for at least the basic requirements to enable all the VLAN's to communicate properly with the ASA?
I'm trying to get some clarity on power stacking 3750X switches. I have a new stack of 6 switches. I know I can only have 4 in a power stack and all 6 in the data stack with a max of 8. I'm trying to find the proper way to connect the power stack cables for the 4 switch power stack.
View 1 Replies View RelatedI need to know if is possible to do a LACP using 2 x 10GB between 3750X and 2960S (WS-C2960S-48LPD-L) switches.
View 1 Replies View RelatedWhat is the difference between IP Base and Universal for 3750X switches?
View 2 Replies View RelatedI'm building a wired closet to aggregate user's connections, Im planning to have 5x 3750X stacked switches and there is a need to run EIGRP, I'm thinking to order one switch with IP service image while the rest will run IP base image, is it workable scenario and what are the drawbacks of such combination of images ?
View 5 Replies View RelatedI have two 3750x stacked switches , both with the latest firmware on them. I enter the configuration onto one switch and it obviously copies over onto the other switch. Although in the configuration I have both a console username and password and an enable password, when I try to log onto the initial switch that I entered the configuration on, I am prompted for a username and password, which works fine, but when I try to enter enable mode i get an error stating that no password has been set. However when logging onto the other switch I am not prompted for a username or password but when I try to enter enable mode I am prompted for a password and can access it with no problems.
View 1 Replies View RelatedWe purchased a number of 3750X 48 and 24 port switches for the College Campus. Am finally getting around to getting them inserted on the network. Working with a WS-3750X-48PF-S and a WS-3750X-24P-L. Have them stacked with the 10Gb uplink on the 48 port switch. Have not been having fun.In the boot sequence, the switches recognize they are stacked, but as soon as they finish boot, I get the message on the 48 port switch: “Stack Port 1 Switch 1 has changed to state down.” Then “Stack Port 2 Switch1 has changed to state down.” Am noticing that I have a message preceding that: “Major version mismatch with stack neighbor.”The 48 port is running c3750e-universalk9-mz.150-1.SE3, HBOOT 12.2(53r)SE2.The 24 port is running c3750e-unversalk9-mz.122-55.SE3, HBOOT 12.2(53r)SE2Most of our 3750X and older switches are running 122-55 or 122.58 code. IP base or Universal. There is speculation that the problem is the 24 Port is Lan base, as the part number might indicate. (WS-C3750X-24-P-L.... I think that is the part number) and the 48 is IP base. Both switches are Universal, and my understanding is that they don't care about LAN or IP Base until you enable a function that falls in the IP Base domain. Then I have to call Cisco Licensing.For these switches, LAN Base is fine, based on the boot message, I feel the real problem is 122-55 versus 150-1 in the stack. So.. the question is: Do I downgrade the 48 port to match what we have in our environment, and what is on the 24 port switch. Or... Upgrade the 24 port switch to match the 48 port switch and have an installation that is not consistent with our environment? I do have two more edge closets to install with this purchase of 3750X 48 port switches.
View 2 Replies View RelatedIn my office we bought 7 cisco 3750X - 48PS switches. We configured Data Stacking between those switches. We also want to configure Power Stacking between those 7 devices.
I found in the Data Sheet that we can only configure 4 devices in power stacking at a time. If it is like that how to configure the rest of 3 devices. Need configuring power stacking between those devices in a better way..
power stack cable part no we have is
CAB-SPWR-30CM
I have a stack of 8 3750x switches connected via Stackwise. In addition, I have these switches configured as two Powerstacks. When I look at the Powerstacks, they are showing as being in power-sharing mode. When I look at the individual switches, they show as standalone. Right now, I have 1 switch in each powerstack that has two power supplies, and then the other three have a single power supply. Below is the output for "Show stack-power detail" as well as the Powerstack configurations.
Power Stack Stack Stack Total Rsvd Alloc Unused Num NumName Mode Topolgy Pwr(W) Pwr(W) Pwr(W) Pwr(W) SW PS-------------------- ------ ------- ------ ------ ------ ------ --- ---Powerstack_1 SP-PS Ring 2145 45 570 1530 3 3Powerstack_2 SP-PS Ring 2860 60 760 2040 4 4Powerstack_1-1 SP-PS Stndaln 1430 520 190 720 1 2
Power stack name: Powerstack_1 Stack mode: Power sharing Stack topology: Ring Switch 4: Power budget: 700 Power allocated: 190 Low port priority value: 20 High port
[code].....
We have a remote site that is using 3750X switches as layer 2 switches back to our home site. The uplink port is showing dropped packets but the utilization on the link is never about 10%. We have a 100Mb circuit to this site. Our speed tests and iperf tests are not showing any issues that we can see. However the port is still droping packets. It is not dropping at a high rate but they are dropping.
switch#sh platform port-asic stats drop gi1/1/4
Interface Gi1/1/4 TxQueue Drop Statistics Queue 0 Weight 0 Frames 0 Weight 1 Frames 0 Weight 2 Frames 0 Queue 1 Weight 0 Frames 52876 Weight 1 Frames 2 Weight 2 Frames 0 Queue 2 Weight 0 Frames 0 Weight 1 Frames 0 Weight 2 Frames 0 Queue 3 Weight 0 Frames 0 Weight 1 Frames 0 Weight 2 Frames 1330874 Queue 4 Weight 0 Frames 0 Weight 1 Frames 0 Weight 2 Frames 0 Queue 5 Weight 0 Frames 0 Weight 1 Frames 0 Weight 2 Frames 0 Queue 6 Weight 0 Frames 0 Weight 1 Frames 0 Weight 2 Frames 0 Queue 7 Weight 0 Frames 0 Weight 1 Frames 0 Weight 2 Frames 0switch#
Is there a way to capture these dropped packets to see what they are? We do have VOIP phones at the site and are using Qos.
I'm building a wired closet to aggregate user's connections, Im planning to have 5x 3750X stacked switches and there is a need to run EIGRP, I'm thinking to order one switch with IP service image while the rest will run IP base image, is it workable scenario and what are the drawbacks of such combination of images ?
View 1 Replies View RelatedI have a bunch of 3750x switches that each have a 10 gig routed link back to a central 4507 (loopback = 172.30.255.255).We carved up a /24 (of course, the /24 doesn't really exist except in our address tracking spreadsheet) into a bunch of /30's for routed WAN links and /32's for loopback addresses.We started on the low end for /30 subnets (ie 172.30.255.0/30, 172.30.255.4/30, etc.).We started at the high end for the /32 loopbacks (ie 172.30.255.255/32, 172.30.255.254/32, etc.)
Well, when I try pinging 172.30.255.255 from the access layer 3750x switches, the 3750x seems to be treating it as a broadcast ping where it lists each member that responds instead of the regular !!!!! response (this makes think something is odd with the 3750x). Of course, only one member responds (the core). But even the core seems to respond with the other end of the /30 instead of the actual /32 loopback (which makes me think something is odd in the core). I could have sworn that I've setup similar topologies without problems (ie, using 10.0.0.0/32, 10.255.255.255/32, etc as loopbacks) and as long as the mask is a /32, it should work.Also, I can ping/ssh to that loopback if my laptop is on a directly connected subnet. But I can't do it from any of the 3750x switches (which are also directly connected).I've double checked for overlapping subnets, but nope. I don't see any. Routing looks fine. The actual /32 is being propagated everywhere properly.
Prior we only had 62.5u multi mode.I've got 3750x switches and new SM SFP and yellow fiber patch cables. None of my links show connected. No lights and trunk port interfaces show down/down.
Is there a special command you have to do on a port when using SM fiber? Do you think I need cross over fibers?
Also, should I be able to see a laser signal light like MM or is SM a different frequency so it's not as visible as MM?
What are the options avilable to add a cat3560 g switch to a stack of 3750x switches.?is there a connector avilable ?or is it possible to trunk via fiber ? cat 3560 has 4 sfps and 224 10/100/1000 ports with poe. cat 3750 stack has a 10 gb up link . What are the possible options?
View 6 Replies View RelatedWhat's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View RelatedI’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other.
- I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit.
- So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
i am using bsnl broadband connection.when i want to connect to internet it is saying that TCP/IP NOT INSTALLED.DISABLE E-MAIL SCANNING IN YOUR SEMANTIC PRODUCT 1003,3. so i removed the semantic anti product. still internet is not connecting. what shall i do?
View 1 Replies View Related