Cisco Switching/Routing :: E4200 VLAN Setup On Wireless AP
Nov 14, 2011I am trying to set up VLAN on my cisco router, where do i check for the setting for creating a VLAN on my Wireless AP. Is it possible on this model.
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Power Connect 6224 With Routing Enabled With Several VLAN Setup
Jan 19, 2013I have a power conncet 6224 with routing enabled with several VLANs setup.VLAN Database: 6,8,10,90-254VLAN 6 is our management vlan10 is for our core network services (DNS, Domain, Exchange etc)90-254 are isolated vlans.What I need to accomplish is to prevent vlans 90-254 from communicating with each other and only allow communication to VLAN 10 and the internet. All internet firewall work will be handled by our Sonicwall. [code]
View 1 Replies View RelatedCisco Switching/Routing :: 3560G - How To Setup Per Vlan Routing
May 14, 2013I'm trying to set up per vlan routing on a 3560G switch but it's not performing as I would expect. I've got a server on the 109 vlan with a 10.1.9.100 address and a default gateway of 10.1.9.1 this address is an HSRP gateway and currently resides on 10.1.9.7. When I traceroute through to my user PC on the internal network it receives a response from 10.1.9.7 However, it is then denied by an ACL on the internal firewall which has been applied to interface Eth0/0. It should arrive at the firewall on Eth0/2.109 as it has the 10.1.9.4 address.
My goal here is to route traffic on the 101 vlan to a seperate interface on the internal firewall from 109 vlan traffic. I'm either doing something wrong or these routing commands aren't designed to work in the way I'm expecting (I couldn't find any documentation on the ip route command where it is followed by different gateways for different vlans)
interface GigabitEthernet0/12
description Internal-FW Eth0/2
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 109
switchport mode trunk(Code )
Cisco Switching/Routing :: Setup VLAN Between 3845 Router
Jan 30, 2012I have a Cisco 3845 Integrated Service Router and I have installed a Service Module. I want to use the integrated Gigabit ports as switch ports and put ports in the Service Module and Gigabit port in a VLAN.
Is this possible? can it be done by setting internal Gigabit link as trunk and how? Below is the somewhat the setup i am looking for
Service module
fa0/1 |
fa0/2 | Vlan X
fa0/3 |
[Code]....
Cisco Switching/Routing :: SG300 - Vlan Setup Automatically Changing?
Jul 9, 2012I have 2 SG300 switches, in layer3 mode, lag'd together for high availability, serving 2 Dell R815's and a Dell Equallogic 4100 for virtualisation. I have setup a number of vlan's, network traffic, mgmnt traffic, iScsi, vMotion etc and they seem to work.
However, Equallogic unit suddenly became unavailable to view for managment yet maintained iscsi traffic for the servers ok. After much head scratching, noticed that one of my SG300's had the vlan ports assigned to various vlans had *automagically* changed there assignment, ie tagged changed to excluded, but only for one of the iscsi traffic connections and the mgmnt port, both coming from the Equallogic, the other iscsi continued its assignment fine. The other SG300 hasn't changed. Guaranteee no one has been into change it and no changes have been made to Dell servers or Equallogic.
Q. Is there any circumstance where the switch can change the port setup itself? or is there any external circumstance that would trigger that change either?
This has now occured twice. The setup is running as a test lab, not in production until all setup is complete, then it will replace our existing harware.
Cisco Switching/Routing :: Setup VLan Between 6509 And 2621 Router?
Oct 25, 2011I need to setup a vlan between the 6509 and 2621 router. This needs to be a VLAN (200) the runs between the devices that uses DOT1Q trunking. The end result is all the networks (vlans) on the 6509 can talk to the LAN on the 2600 (10.133.22.0 / 23) and visa versa.
Device 1
6509 with CatOS / IOS
Config I did on the MSFC:
Interface Vlan 200
ip address 10.10.10.1 255.255.255.248
[code]....
Cisco Switching/Routing :: ASR1002 Config To Setup Simple VLAN
Dec 19, 2012I am attempting to upgrade from a Cisco3945 to a ASR1002. On my Cisco3945, I have interface associated with VLANs. It appears that with the new IOSX, VLAN configuration has changed. Any config to setup a simple VLAN?
View 5 Replies View RelatedCisco Switching/Routing :: Setup VLan To Allow Video Traffic Between 2960 And 3750?
Nov 13, 2011I am trying to setup a network using Cisco 2960 switches with vlans configured. One vlan will handle video coming from four cameras that are connected to another 2960.
We have four cameras feeeding one port each on a 2960, that 2960 in turn feeds one port on the main 2960 which is the video vlan for that site. From the site it goes back to a Cisco 3750 to be sent over to a Sonicwall firewall. If we connect to the 2960 that the camera are connected to we can see the video, but not on the main site 2960.
Cisco Switching/Routing :: 3560 Possible To Create Vlan Inside Transport Vlan?
Jan 10, 2012Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedCisco Switching/Routing :: 3750 - Extending VLAN To Remote Switch That Already Has VLAN ID In Use
Jan 10, 2013I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
Cisco Switching/Routing :: Route Data From Vlan 10 To Vlan 20 On 2960s?
Mar 31, 2013i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
Cisco Switching/Routing :: 3750G / VLAN 1 Is The Only VLAN And Its Disabled
Sep 16, 2012I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies View RelatedCisco Switching/Routing :: L2tpv3 Vlan-to-vlan Tunnel On 890
Jun 13, 2011I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
Cisco Switching/Routing :: Low Bandwidth On 3750 From Vlan To Vlan?
Nov 20, 2012We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
Setup Inter-VLan Routing On A 4800G Switch?
Feb 3, 2012I'm looking to setup Inter-VLan routing on a 4800G switch.
I'm looking for all workstations (VLAN1) to be able to talk to the windows network (VLAN2) and to our Novell network (VLAN3)
but I don't want Windows (VLAN2) and Novell (VLAN3) talking to each other. Is this possible accross a single switch? I have 7 switches available to use if needed.
Cisco :: SF302-08 VLAN Setup - VLAN Cannot Communicate With Each Other?
Nov 27, 2012I am trying to set up a Vlan on an SF-302-08 small business switch. I would like two Vlans both with internet access but the two cannot communicate with each other. I am not really sure how to go about setting this up as its all fairly new to me. I have successfully set up the Vlans and the ports on each VLAN cannot communicate with each other however the internet access will only work when plugged into either VLAN but wont work on both together
View 1 Replies View RelatedCisco Switching/Routing :: FS728TP Cannot Get Wireless To Tag To VLAN
May 26, 2013I have a netgear FS728TP configured with 2 VLANs. The primary untagged vlan 1 is data and goes out our FW, vlan 2 tagged is voice and goes out our VOIP router, both of which work(the phones being directly notated as VLAN2).
-vlan 1 pulls from our primary data DHCP issued from our DC
-vlan 2 pulls from our primary voice DHCP issued from the voice router
We have a Cisco aironet 1250s setup to issue our main network SSID and a guest network SSID.The main wireless works configured with the native vlan 1 and issues the DCHP scope fine.The guest which is labeled as VLAN 2 however does not.How do I get the aironet secondary guest wireless to tag as vlan 2 and pull dhcp from the voice network?(im not worried about guest getting higher QOS, its a 50/50mb connection for 25 users, and guests are rare, I just want it to work without guests having access to internal resources)
Linksys Wireless Router :: Vlan Tagging On E4200 / WRT610n?
Feb 14, 2012I rencently bought the E4200v1 router, to be wired together with my WRT610nv2 to form gigabit network for different floor network.However with the recent installation of fiber to home network offered by my local ISP, I would need router that capable for performing vlan tagging (500 for internet & 600 for IPTV).Would like to know if Cisco have any development plan to enable the VLAN option for:-
1. E4200
2. WRT610nv2
At the moment, I'm still stuck with the provider "home-made" router which lacks of Gigabit & dual band wireless.
Linksys Wireless Router :: How To Setup E4200 As WAP Only
Jan 5, 2013I am connecting the E4200 to a Sonicwall TZ100. I want the TZ100 to assign IP addresses to devices that connect to the LAN via the E4200.
How do I have the E4200 act as a WAP only or not assign IP addresses and push that responsibility to the TZ100?
I'd still want the E4200 to have a SID key for LAN access security.
Cisco Wireless :: Setup VLAN On ASA 5510?
Apr 18, 2013I am looking to set-up an isolated WLAN for the users in my organization and how to proceed What I have is the following
Cisco 5508 Wireless LAN controller
Cisco Catalyst 3750 24 port (not sure what exact model)
Cisco AIR-AP1131AG-A-K9 POE Access Point
Cisco ASA 5510
Currently what I would like to do is to setup a VLAN on the Cisco ASA 5510, connect the Catalyst to the VLAN and connect the 5508 Wireless LAN to the Catalyst via Fibre. From there on in - I would connect each AP to the Catalyst? The proposed scenario is that the VLAN would be in a DMZ and have direct access to the Internet without any filtering and users would connect their devices to the AP and get a DHCP address and be able to surf with freedom?The problem is - I am unsure as of where to start. I have been certified Cisco in 2001, however I havent started to use my skills until now.The Vlan would be the following: 192.168.20.X
Linksys Wireless Router :: Can't Get Setup CD To Install E4200
Oct 20, 2011I have XP 64bit OS and I can't seem to get the setup CD to install E4200 Router. I have looked at the FAQ and it says it should be compatible with all Windows OS. Is there a link out there to the drivers I need to do this?
View 1 Replies View RelatedLinksys Wireless Router :: E4200 Setup As Repeater?
Jan 25, 2012I use my e2000 as router and want to use the e4200 as repeater. so if i connect wireless to my e4200 i can see all my devices also the one on the e2000. How to setup the e42000 ?
View 5 Replies View RelatedLinksys Wireless Router :: E4200 Hangs During Setup?
Dec 3, 2011Have been trying for the past two days to install a new E4200. It gets to 25% in the setup and then errors out and says I need to contact customer service.
Connecting through a brand new DSL modem that I know works as I can get access through my old router.
My PC (Windows 7) is directly connected to the router. I got to the point where I named the router in the install process the first time, but then it hung.
Have tried to use the CD to re-setup with no success. I've tried the hard reset holding in the button for 10 seconds and unplugging but nothing has changed.
Linksys Wireless Router :: IPv6 Setup For E4200?
Jun 11, 2012Our internet provider has no intention of providing a IPv6 DNS so I have a crippled at best service. We live in an area where our only option is through satellite service, so changing providers in not in the cards, yet.
If I "Disable" the DHCP Sever, the setup menu provides a method for me to force feed up to three Static DNS addresses, all with IPv4 addresses.
There are several locations that provide "free" DNS service, but how does one verify the security of such sites? Does Cisco keep track of the status of this kind of service or am I on my own? Cisco seems to endorse two DDNS services, but for home use, the extra charges seem otherwise unnecessary, and do not yet address the IPv6 question.
The first few that I have investigated that do provide IPv6 service also provide their addresses in IPv6 format. The E4200 menu does not seem to allow me to do that.
Am I going to be forced to live with crippled IPv6? I have already discovered a software product that has failed since changing routers, but works if I take my laptop to a particular WiFi location.
Linksys Wireless Router :: How To Setup Remote Access With E4200
Aug 11, 2011how to setup the E4200 so that I can access the media server when I am in office? I was browsing on the Cisco website and unable to find it.
View 8 Replies View RelatedLinksys Wireless Router :: Setup VPN Access To My House Through E4200?
Oct 11, 2011I've got an E4200 at my house. I'd like to know if it's possible for my to establish a VPN connection from a remote location to login to my E4200 to get access to my computers behind the firewall.
View 1 Replies View RelatedLinksys Wireless Router :: Cannot Setup E4200 - No Internet Connection
Aug 9, 2011I just purchased e4200 from a friend of mine. Got an issue with setup of this device. I use a model from internet provider. Have 2 computers at home. One is pc with cable, another one mac with wireless.SO my issue is that i can not connect none of them. I was trying to use cd that comes with router but he can not locate a router. When I connect cable directly from modem to computer everything works fine. As soon I connect cable to a router I can not see a router and I can not connect to internet.
View 1 Replies View RelatedLinksys Wireless Router :: How Does One Connect To Each E4200 On Network For Setup
Jul 30, 2011So, with the latest firmware update I could add a second e4200 to my network to use as a bridge or access point? What I need is another device in my living room that can pick up the wireless signal and dish out network connectivity to my receiver, xbox360, and ps3. With the new firmware update can this be done with a second e4200? How does one connect to each e4200 on the network for setup (dohave to change the default ip address of 1?)I just bought a trendnet TEW-687GA 450 mb/s wireless gaming adapter and a trendnet 5 port switch to accomplish what I mentioned above. I'm just wondering if there is an advantage to switching over to two e4200's. The trendnet adapater does not have a 5ghz channel.
View 2 Replies View RelatedLinksys Wireless Router :: E4200 / How To Setup Main Computer
Jan 16, 2012I got a problem with my setup main computer, It work wery god wireless, with very fine speed about 82 mbit in and 24 mbit out. The problem is that it almost don't work at all with cable, even if i turn off the wireless network, the speed is about 2-3 mbit in and about 6-7 mbit out All other computers, tv. printer wireless work very fine.
View 2 Replies View RelatedCisco WAN :: Setup VLAN In ASA5510 For Guest Wireless Access?
Feb 10, 2012I am running a /24 network in Active Directory with my ASA acting as gateway and firewall. Standard interfaces (Ethernet 0/0 as outside, Ethernet 0/1 as inside)
As of now I have no VLans set up, but I need to setup wireless Internet access for guests... I need directions on how to setup a Vlan with its on DHCP for these aguests... I can then make sure that my APs can be pointed to the same VLAN... I am not familiar with CLI, have generally used ASDM. I am currently running ASDM 6.3(1) on an ASA with version 8.3(1).
This is something I need to do quickly as we are expecting 20-40 "guests" shortly, and I don't want them to use our internal DHCP server addresses.
Cisco Wireless :: 144 / Client MAC On Native Vlan In H-reap Setup
Jan 11, 2012Just trying to figure out how LAP manage clients in a h-reap setup.Have a setup with native vlan on 144 (switch and AP) and ssid tagging in other vlan... Got this on switch:
Jan 12 10:31:43.121: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0811.9695.9b04 on port FastEthernet0/42.
Jan 12 10:31:43.121: %PORT_SECURITY-2-PSECURE_VIOLATION_VLAN: Security violation on port FastEthernet0/42 due to MAC address 0811.9695.9b04 on VLAN 144
Jan 12 10:37:42.770: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0811.9695.9b04 on port FastEthernet0/42.
Jan 12 10:37:42.770: %PORT_SECURITY-2-PSECURE_VIOLATION_VLAN: Security violation on port FastEthernet0/42 due to MAC address 0811.9695.9b04 on VLAN 144
Wonder why clients MAC is seen on native vlan (and ofcourse also on taged vlan) ...?
Cisco Switching/Routing :: How To Migrate From Fixed Router To Vlan Routing On 4507
Feb 16, 2012Any "best practices" or recommendations on how to migrate from a fixed router (3745) to vlan routing on Catalyst 4507 switches in order to minimize the disruption to the network.
View 4 Replies View RelatedCisco Switching/Routing :: Multiple VLAN Routing Tables For 3750 Catalyst
Oct 24, 2012I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies View Related