Cisco WAN :: Setup VLAN In ASA5510 For Guest Wireless Access?
Feb 10, 2012
I am running a /24 network in Active Directory with my ASA acting as gateway and firewall. Standard interfaces (Ethernet 0/0 as outside, Ethernet 0/1 as inside)
As of now I have no VLans set up, but I need to setup wireless Internet access for guests... I need directions on how to setup a Vlan with its on DHCP for these aguests... I can then make sure that my APs can be pointed to the same VLAN... I am not familiar with CLI, have generally used ASDM. I am currently running ASDM 6.3(1) on an ASA with version 8.3(1).
This is something I need to do quickly as we are expecting 20-40 "guests" shortly, and I don't want them to use our internal DHCP server addresses.
View 3 Replies
ADVERTISEMENT
Mar 26, 2013
I have registered here to clarify some things about VLAN's. There are so many (different) names and mentions that i found tat my vision gets blurry looking through all the info.I have a setup at a client where the Guest WiFi access needs to be separated from the normal LAN where all the normal devices are attached to. The guests are not allowed to reach the IP camera's and printer etc. etc. . I am trying to visualize how the traffic should flow but the Tagged, Untagged, PVID, Trunks and other names that i found make it difficult for me to see how it works together.
View 8 Replies
View Related
Apr 8, 2013
Any issue creating a guest vlan to use the WIFI on an 891W router? The IOS is version 15.1. I have created discreet Vlan's and setup subinterfaces on both the WLAN_AP0 and GigaEthernet 0 interfaces with dot1q encapsulation. The client will receive an IP from the pool but cannot ping or connect beyond the default gateway.
The external interface is using Nat overload and all wired clients are successful in connecting to outside addresses. I have insert a permit any statement in the acl which affects the external port but still no success.
View 7 Replies
View Related
Jul 11, 2012
Hardware: Cisco 3750 switch and Cisco autonomous access point (AIR-AP1142N-E-K9).Requirement: A single broadcast SSID; use dot1x to assign vlan 98 to authenticated clients (computer certificate); assign vlan 3 (guest) if the authentication fails.I can achieve assigning a guest vlan on authentication failure when using a wired connection by using the following command on the interface:authentication event fail action authorize vlan 3 I'm after a way to achieve the above using the wireless access point. The main point is that internal users cannot access vlan 3 as they have a valid certificate and that guests do not have to authenticate.
View 2 Replies
View Related
Jun 4, 2012
I have setup guest access on the controller and this is not working at the moment. DHCP server setup on the controller for the Guest users. You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
View 10 Replies
View Related
Jun 23, 2012
I have some Cisco 1240 Access Points which are not centrally managed. I want to add 802.1Q trunking so as to be able to provision a guest VLAN. But a trick is that these APs are in some very high ceilings. I would like to provision the new trunking and guest VLAN without having to remove them from the ceiling. Someone suggested I just make the native VLAN save as existing and make the port to which attaches a trunked port. But when I did this I lost connectivity to the Access Point. Access came back as soon as I made the switch port an access port. how I can add the trunking and guest VLAN without having to get into the ceilings to remove them and configure them via console or other?
View 2 Replies
View Related
Aug 18, 2011
Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies
View Related
Aug 30, 2011
Recently implemented an ASA5510 and I cannot setup RDP access. I've browsed these and other forums and tried all the suggestions that I've been able to find and still no luck.
View 13 Replies
View Related
Oct 12, 2011
I'm wanting to setup a Virtual Office scenario. Everything is working fine except for 802.1x...I can get the 881 to authenticate things connected to it, but I don't have the options of guest-vlan or auth-fail vlan.Idea is if the users takes the router home and someone, either accidentally or on pupose, connects an unauthorized Laptop, they stay off the Corp network but can get to the internet still.I found this link on Cisco's site: [URL]That link shows them configuring a guest vlan right on the fa0-3 ports of an 881W. I dont have that option on mine. I can only configure 802.1x on the vlan interface. I have 802.1x working, for things that connect to vlan1, but I would like to have a "fallback" setup.
EZVPN_Remote(config-if)#int fa1
EZVPN_Remote(config-if)#dot
EZVPN_Remote(config-if)#dot1?
dot1q
EZVPN_Remote(config-if)#dot1
[code]....
View 1 Replies
View Related
Apr 5, 2013
So I've got an odd issue here, have an older 4948 that I'm trying to setup on our management vlan so i can manage it from another host connect to the switch. I can't figure out why its not working. Below is the config
vlan is 64 and all the trunk and access ports that are on vlan 64 are working just fine. Just can't hit the switch from a machine on the 64 vlan.
!
interface Vlan1
no ip address
[Code].....
View 9 Replies
View Related
Mar 18, 2013
I am extremely new to network but also excited with the things you can achieve with a Cisco switch.For about 3 months I sat down looking at my "Cisco C2950-24 Switch", this surely for such a beastly looking thing it must be able to do something other than just allow you to plug in cables. So with that said I started to do some reading and watched a couple of You Tube Videos.I am on the route to complete my first goal and thats have my own VLAN setup with 1 Server and 6 clients. The Server is running ESXi therefore a few other servers are running inside it too.So my VLAN - VLANID 20 running the network 172.22.22.0. On the physical switch I have the following:Port 1 - WAN incoming connection from my Router on the network 192.168.178.0Port 2 thru 9 all running on VLAN 20.By the way I am using the GUI Cisco Network assistant
View 4 Replies
View Related
Nov 7, 2011
I have a Dell switch setup with 2 Vlan's. Vlan 1 is to the network. Vlan 20 is going to be for wireless access to the internet. How do I configure the switch/router so that Vlan 20 only connects to the internet and not the network? I will later want to have a 2nd SSID that I want to connect to both the internet and network.
View 5 Replies
View Related
Sep 6, 2012
My company has an RV180W Router, a SGE-2000 Managed Switch, and a WAP321 Wireless Access Point. I have about 12 users on a Windows 2003 Server Standard, completely updated. My Win box is my DHCP Server. Now I am running two VLANS, Vlan 1 (default) the main vlan is where the Win box is on. Vlan 5 (guest Vlan) uses the RV180W as the DHCP server.
-Vlan1 is 192.168.1.1-254 - Issued by Win box
-Vlan5 is 192.168.2.100-254 - Issued by RV180W
View 3 Replies
View Related
Jan 27, 2011
I have a AP541N connected to a UC560. We are currently configured for Wireless Voice and Data. We have added a Guest VLAN, but don't see where in CCA to secure the VLAN from accessing the other other two default VLANs.
Additional Info: AP541N-K9-1.7(2)UC560 15.0(1)XA2, RELEASE SOFTWARE (fc2)CCA 3.0
View 1 Replies
View Related
Jul 24, 2012
I am trying to setup a Wireless Network on my WLC that is totaly independent of our internal LAN. Port1 is designated at the .14.0 network and Port2 is the .18.0 network. The 14 network (Port1) will be the guest and 18 network (Port2) the internal wireless.
The issue i am having is nothing is routing to Port1. I have the Guest Wireless set to get DHCP from the WLC and i can get an address but i cant get internet access. I tried configuring a Network Route but it will only let me set the service port as the Gateway and not the IP for Port1.
I am running software version 5.1.151.0 and using this guide as it is the only one i can find. [URL]
Here is a screen shot of my Interface config.
View 7 Replies
View Related
Jun 4, 2012
I have setup guest access on the controller and this is not working at the moment.
DHCP server setup on the controller for the Guest users.
You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
View 2 Replies
View Related
Feb 23, 2012
In our test set up, we have two WLC 5508 Controllers connected via Checkpoint UTM-1 firewall Inside and DMZ Interfaces. Both the WLC controllers are connected to the firewall via Cisco 3750 switch. On the Local (Inside) Controller, guest SSID is enabled and attached to the wireless management Interface. On the remote anchor controller, guest SSID is enabled and attached to the Management Interface as well. The following configs are replicated on both the Controllers.
SSID Name - guest
Interface - Management ( VLAN 10 on Local and VLAN 20 on remote) -
Mobility Group: Same configs at both ends
SSID Anchor : Anchor SSID on local and local SSID on Anchor.
AP: CAPWAP 3502 Management Subnet
[code]....
Is there any thing missing in the wireless configs and or the firewall rules as i could not see DHCP request back from the Anchor Controller. Also, after DHCP is obtained, the web authentication request will be redirected to an Amigopod device for authentication. In this case is the redirect URL congiguration to be performed only on the Anchor Controller or is this to be replicated on both the Local and Anchor Controllers.
View 8 Replies
View Related
Mar 6, 2012
We are trying to setup a WAP4410N with 2 SSID's. One SSID for our private network and the other for guest internet access. On the VLAN and QoS page there is a setting for priority. What would be the suggested values for this setting? We obviously want our private network to receive priority over our guest network.Also, does VLAN Tag setting need to be on Tagged to determine private from guest traffic?
View 2 Replies
View Related
Dec 11, 2012
how to setup a separate SSID for guests (without a password).
Basically, we have one SSID now called Mnet which has a WPA2 password. For guests coming in i want Mnet Guests where people can connect without needing a password. They should be able to use internet but not connect to LAN devices, how to accomplish this with this WAP321?
View 7 Replies
View Related
Jan 2, 2012
We currently have a Guest wireless setup at my company, instead of using a anchor controller we have dual contorllers with each having one interface connecting out into our dmz and then going out. it's a pure L2 connection and exits out to the internet via a DMZ interface on our ASA. We recently purchased a PA-200 Palo Alto firewall to use for this Guest network, and configured everything exactly how it's all ready setup on our dmz switch and asa with the same ip addresses. When we connect the outside interfaces from the controller to a L2 switch that's connected to the Palo Alto firewall we can't get dhcp requests thru and have no connectivity, even if we set a static IP on our client we still have no connectivity and it won't redirect us. We use Web-Auth for our authenication with this network and I know once you get an IP address it will only allow dns to redirect to the virtual IP for authenication before it allows anything else but it is the exact same setup as we had before just with a different firewall so I'm stuck. Also if I plug directly into the switch via ethernet cable I can get an IP address and get out to the internet.
View 13 Replies
View Related
Aug 28, 2011
We're looking at deploying both office extend and also a guest wlan. Both would require a WLC in the DMZ.My question is can one 5508 WLC be both a guest anchor and have office extend APs on it at the same time?
View 2 Replies
View Related
Nov 27, 2012
I am trying to set up a Vlan on an SF-302-08 small business switch. I would like two Vlans both with internet access but the two cannot communicate with each other. I am not really sure how to go about setting this up as its all fairly new to me. I have successfully set up the Vlans and the ports on each VLAN cannot communicate with each other however the internet access will only work when plugged into either VLAN but wont work on both together
View 1 Replies
View Related
Apr 6, 2010
I just installed my new Cisco E3000 and configured it over the HTTP interface, as I have on previous routers. I am unable to find any setting for the "Guest" wireless network (outbound internet only), or the Parental controls. Both of these are features of interest, and they're simply not listed in any of the web-based settings.
Puzzled, I did a Factory Reset and configured it via the Cisco Connect instead.. this had the Guest feature and Parental controls, but none of the other features I need, like QOS, or Port Forwarding, or DHCP disable.
It seems like the Web interface only configures some settings, and the Cisco Connect configures other settings, but I can't use them both.
Where does one set up the additional password for Guest access? Other than this, the router works fine on 2.4 & 5 GHz, nice..
View 9 Replies
View Related
Jan 25, 2011
A query here with regards to Wireless isolation between SSID and wireless isolation within SSID.If we have 2 SSID, eg. InternalSSID, GuestSSID on AP1.Both SSID are set to Enabled for isolation between SSID, and within SSID, that would mean all machines connected thro' this AP1, would be isolated from one another.
1) If there's 1 laptop that connects to another AP, lets call it AP2, (doesn't have isolation function) on ssid01. Would this laptop still be isolated from those that connects to the first AP?
2) If there are wired PCs connected to the router. And the 2 APs are connected to the same router. Would the machines connected thro' the AP1 on either InternalSSID, GuestSSID be able to access those wired PCs? (My assumption is yes.)
3) Is there a quick and efficient way to setup on WRVS4400N to isolate GuestSSID totally from InternalSSID, and wired PCs. InternalSSID and wired PCs should be allowed to 'see' one another.
The challenge here is that, the network points are all installed already. Both AP are connecting thro' 2 separate unmanaged switch together with a couple of other PCs. 1 Port on the unmanaged switch, each,connects to the router.
View 1 Replies
View Related
Mar 20, 2012
I used Cisco connect to set up guest access with a secure password. Cisco Connect now indicates guess access is allowed and shows the password. However, when I actually try to connect to the guest network, it shows no security at all, and I can join the network without a password.
View 1 Replies
View Related
Apr 19, 2012
I got the task of setting up a Guest wireless network for one of our remote campuses. We already have some APs that are connecting to our WLC.
The Enviroment:WLC Cisco 5500 is at our Corporate office. Connects to our Core Switch then to our Router Router connects to our remote campuses over mpls.
We currently already have APs at this campus that are connecting back to our WLC.
We have a DSL line at the remote campus that we want this Guest wireless routed to.
I have already created the guest network on the WLC and a guest VLAN on the Core switch.
My main question is how to configure the two routers for this and have this go out the DSL modem?
View 9 Replies
View Related
Feb 26, 2013
Just got a new EA3500, and plan to use its guest network feature to allow Internet access but not access to my LAN. Wondering if I can set it up so that users on the guest network bring up a particular website when they open their browser.
View 3 Replies
View Related
May 9, 2012
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
View 10 Replies
View Related
Nov 27, 2011
I am primarely enquiring whether the setup I have explained below is actually possible, and if so then how I can set this up. I know it isn't the easiest configuration and I need to set this up without purchasing any more equipment if at all possible.I have a Cisco SG 300-28 setup with three VLAN's. [code] Default Gateway is 192.168.10.1 (Netgear Router)I have a Wireless network setup (Netgear WMS and 2 WAP's) configured with the TWO VLAN's (1 and 3). These go into ports on the Cisco SG 300-28 which are tagged on both VLAN's. The Business wireless worked fine but the guest network didn't reout out to the internet.After some troubleshooting I realised the reason the guest wasn't working was because there was no route back from the internet to the router.
The router I have isn't really ideal, it is a Netgear DGN2200, but I managed to create a static route to 192.168.30.1 with a metric of 2, with 192,168,10.254 being the hop. Success, the connection worked, the only problem is that now my guest network can see my business network because the business network is using the static route on my router to route back over to the guest network (due to the limitations of this device I can't do anything about that)Guest network can connect to Business VLAN via switch. I am assuming this is because the router is on the Business VLAN and the default gateway is the router. As they are on the same network the Guest network can inevetably see the business server and network.The Business network can get back to the Guest network via the router using my static route I created. The static route is really basic and I can't create a firewall rule on the router to prevent the Business network speaking to guest network because it only has a LAN - WAN firewall and this connection is LAN - LAN.
What I need is...to somehow stop any traffic from the 192.168.30.0 network routing to anything on the 192.168.10.0 network, appart from the router on 192.168.10.1.Is this possible? I have this setup on a number of different site, the only difference is I have a CIsco Security Router on these with the VLAN's configured so I don't have this problem. Because I have a rather limited Netgear DGN2200 I am unable to setup the VLAN's correctly and as such I need to see if I can do this on the switch in any way.
View 2 Replies
View Related
Jul 13, 2011
is it possible to set the dot1x guest-vlan on a Catalyst Switch via ACS 5.2 dynamicly. I want to make MAB with known Devices (FAT-Clients, Notebooks, Desktops, Printers) and unknown Devices.I will set the VLAN dynamicly with dot1x per ACS. For known FAT-Clients, Notebooks etc. it's running well.But for Printers it's more difficult because I have about 500 Printers in several IP-Segments on several Switches and I will not make to much Rules in ACS for Grouping, Mapping and Authority-Rules.My Idea is to set the Guest-VLAN on every Switch, read them with ACS and use this for my Printers.The Problem is that Guest-VLAN is set on more than 100 Switch and this guest-vlan is different on any Switch.Can I read the Geust-VLAN Value so that I can set this via ACS ?
View 4 Replies
View Related
Apr 15, 2012
I know "Guest Vlan" aren't available on SG200, only SG300 have that feature.Problem is i only have a SG200 on hand and no extra budget.
We have multiple vlan:
vlan10: LAN
vlan20: Voice
vlan30: Guest
vlan50: Servers
vlan100: Lab1
vlan200: Lab2
Since it's a small business and lot of people moving around, doing test, etc.... most port are tag with all vlan. Our Wireless AP have multiple SSID one with vlan10 and one with vlan30 for guest.
Is there any way without the "Guest vlan" feature that i could have with my equipment any equipment without a vlan configuration be set on vlan30 ?
View 15 Replies
View Related
Aug 10, 2012
I have a working environment but wondering if there is just a better way to accomplish what I am trying to do (without a layer 3 or 4 switch). Basically I have a few sub interfaces on my Cisco ASA5510.
Now what I do need is some of the VLANs to communicate with specific devices on the different VLANs. So for example I need computer 1 from VLAN 5 to communicate with 192.168.10.5 from VLAN 10 on ports 80 and 443.
What I am currently doing is settings the security level to 100 on each interface (including the DMZ).
Here is what I have:
interface Ethernet0/1.5
vlan 5
nameif Sub5
[Code].....
View 5 Replies
View Related
Apr 9, 2012
I have a 2960 sw configured for dot1x authentication, the problem is the Guest VLAN and Restricted VLAN didnot work. The switch port was stuck in authenticating status. The server is Juniper IC4500.
View 2 Replies
View Related
