Cisco Switching/Routing :: 881 Vlan Administratively Down After Each Reload Or Power Down
Feb 19, 2013
I have a problem with the Cisco 881 router at one of our customers.It seems that after a "no shutdown" has been given on the Vlan interface, it still goes back to "administratevly down" after a reboot.So when I restart the router I always have to manually "no shutdown" the Vlan interface to come back up.While rebooting the router it also gives the following info in the console screen every time which is strange:
new interface Vlan1 placed in "shutdown" state.We tried several different firmware releases.
Replacing the router with a new Cisco 881 router did not work either. After they sent back the old Cisco 881 router we tested it here and there were no problems, we weren't able to replicate the problem.The configuration we use for the router is correct, we use it for hundreds of customers, so that can't be it either.The customer uses a fortinet firewall behind the router. Could it be that something inside the LAN of the customer that triggers the Vlan to shut down?
View 1 Replies
ADVERTISEMENT
Dec 10, 2012
read the posts regarding vlans that are administratively down, they suggested that they are down if no ports are assigned to them, however I do have a switchport assigned, and the interface is still down. This is on the vtp server and on the clients. The vlan is not listed when issuing show vlan brief. Other vlans configured in a similar way do show and their interfaces are up. These are two Catalyst 4948-10G.Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG5, RELEASE SOFTWARE (fc1).
View 5 Replies
View Related
Jan 19, 2013
I have a power conncet 6224 with routing enabled with several VLANs setup.VLAN Database: 6,8,10,90-254VLAN 6 is our management vlan10 is for our core network services (DNS, Domain, Exchange etc)90-254 are isolated vlans.What I need to accomplish is to prevent vlans 90-254 from communicating with each other and only allow communication to VLAN 10 and the internet. All internet firewall work will be handled by our Sonicwall. [code]
View 1 Replies
View Related
Dec 12, 2012
I've just purchased a new Cisco 881.I'm using NAT NVI for my inbound static mappings. However, regardless of the fact that the config is saved to nvram, after a reload of the router, the NAT mappings are setup as traditional inside/outside mappings. This means that inbound connections in to the router on the required services fail, until someone logs on to the router and re-applies the NVI mappings.
Here's a sanitised version of my startup-config:
!
! Last configuration change at 20:20:15 UTC Tue Dec 11 2012 by xxx
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code].....
View 20 Replies
View Related
Nov 29, 2012
SSH has been enabled on our one and only 4507 switch for several months and working fine. A few weeks ago the switch had to be reloaded and when it was back online I couldn't SSH to it. When I connected via the console and typed "show ip ssh" it came back saying I needed to generate the keys. Did that and it starting working again. The same switch had to turned off and on the other day due to a power down in the server room and when it came back the same thing happened again!!
The version of IOS is: cat4000-i5k91s-mz.122.20.EW
View 1 Replies
View Related
Mar 11, 2013
I have a cable from an SFP module in a WS-C3750-48P with 12.2(55)SE1 running to a Gigabit port on a Cisco WLC. After the switch recovers from a power failure, the gigabit autonegotiation fails. The cure is a long drive to unplug and reseat the SFP. Note this happens at too many similar sites for this to be a loose connection. Interface shutdown then 'no shutdown' is not sufficient. The state is 'line protocol is down (not connected)'. Interface is configured for switchport mode trunk (auto speed, auto duplex). Command 'switchport nonegotiate' makes no difference. Is there a more powerful command than 'shutdown' which might toggle the interface signals? Is there some way of resetting the SFP? sh int gi 1/0/1 displays 'media type is 10/100/1000BaseTX SFP' and zero packets received.
View 4 Replies
View Related
Feb 26, 2012
Last night, the C6509-E do a unexpected reload. In the crashinfo, I can see that the last error message before the reload, was as follows: %C6K_ PLATFORM-SP-2-PEER_RESET: SP is being reset by the RP
I consulted the cisco website about this error message and what I found was the following:C6K_PLATFORM-2.
View 1 Replies
View Related
Mar 9, 2013
We have a backup sup 720 which has a 2 gigabit ethernet though port channel, to another chassis. Suddenly UDLD detected an error and got into err disable, then this err disable didn't let the interface set to DOWN, and created a switch loop, then our Supervisor reloaded. I'd like to know what could have caused this reload. In my opinion could have a been the switch loop, but also I've been checking from the output interpreter the show tech and might have been a bug, the only one that could match in IOS version 12.2(33)SXH, is this one: url...
We're going to disable err-disable next time I guess and recover the link manually, apart from that what could have made the sup for crash and reload?
View 4 Replies
View Related
Jul 31, 2012
Suffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?
View 1 Replies
View Related
Dec 15, 2012
while i am configuring a port on switch .The switch reloads.After reload the show version says
System returned to ROM by bus error at PC 0x458F6C, address 0x0
show version from the effected switch is
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[cODE].....
View 2 Replies
View Related
Jun 3, 2012
Our router suddenly reloaded. Below are the crashinfo obtained:
1st crashinfo:
7606_Router#more sup-bootflash:crashinfo_20120604-02260500:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
[code]....
We are running s72033-advipservicesk9_wan-mz.122-18.SXF9
View 14 Replies
View Related
Oct 13, 2009
I have a Catalyst 4500 WS-C4506 and S-X4516-10GE Supervisor running under IOS 12.2(52)SG IP BASE SSH. After having installed IOS 12,2(53)SG i wanted to schedule a reload. After entering the reload at command I get the message %Reload in Progress and nothing happens.
View 4 Replies
View Related
Sep 12, 2010
I have the following problem with
Situation:
- 2x 3750G-12S Distribution-Switches (DS) and several 3560/2960 Access-Switches (AS)
- redundant Fiber optic uplinks between AS and DS
- Cross-Stack Etherchannel config on all uplinks
- UDLD aggressive mode configured on all uplinks
Problem:
- when I reload the DS and the switch comes up again, I've lost the connection with several (not all) AS
- looking at the AS log I found the following error message: "%UDLD-4-UDLD_PORT_DISABLED: UDLD disabled interface Gi0/1, aggressive mode failure detected"
Cause:
- in the log of the AS I don't see intf Gi0/1 go down during the reload of the DS
- this means the DS didn't shuts down all its ports during the reload
- but this also means that UDLD on AS didn't know about DS reload, and therefore didn't resets counters
Workaroud/Solution
- I'm now configuring errdisable recovery on all AS
So I'm forced to configure errdisable recovery, even if I don't want.
View 3 Replies
View Related
Jul 10, 2012
I would like to test the possibility to reload devices via SNMP for new switches like 2960, 3560 and so on.I know that the command "snmp-server system-shutdown" has to be configured, then I need to send the set query to the device via SNMP.
I have found on the net the OID 1.3.6.1.4.1.9.2.9.9.0 but it belongs to an old MIB and doesn't seem to work with new switch models.
View 4 Replies
View Related
Jun 9, 2013
I am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
View 1 Replies
View Related
Sep 4, 2012
After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
View 5 Replies
View Related
Apr 14, 2013
We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
View 1 Replies
View Related
Feb 28, 2011
I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
View 3 Replies
View Related
Apr 4, 2012
In a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies
View Related
May 3, 2013
I am not able to find the exact bug for Cisco 3750E stack - Debug Exception (Could be NULL pointer dereference) Exception (0x2000) error. Closest i can find is CSCsa72400 which only affects ver 12.2(20)SE4.All the stacks (3 switches) are running 12.2(50)SE3, It appears that the switch 1 crashed and reloaded. My hunch is its software but i cant find any related bugs. It could be hardware issue as well ?
View 4 Replies
View Related
Apr 5, 2012
I have just upgraded 2 3750 switches in a stack via the master and reloaded the master switch remotely, how can I reload the 2nd (member) switch?
View 16 Replies
View Related
Nov 7, 2011
I uploaded a new config file via TFTP to a 3560 switch. What are the order of commands to get it to boot from this new config file instead of the file listed in 'sh boot': [code]
View 7 Replies
View Related
Apr 22, 2012
I have one 4506E switch working in Lan setup as a core switch with WS-X45-SUP6L-E running ipbase IOS 12.2(54)SG1. Each time after reload the switch we found that the clock is getting reset ( time is getting changed ) where as day, date & year is unchanged.
View 2 Replies
View Related
Sep 15, 2012
I had a strange issue with one of my customer..Cisco WS-C3750X-48P Access switch was not reachable and after reload it started working.I would like to know the root cause of the issue. There were no logs and no errors in interfaces.Even Cpu utilization was not high. We have enabled arp inspection and dhcp snooping in the switch..Hope this will not make any issue..Also we have dot1x enabled on port..
View 5 Replies
View Related
Jan 10, 2012
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies
View Related
Jan 10, 2013
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
View 4 Replies
View Related
Mar 31, 2013
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
View 4 Replies
View Related
Sep 16, 2012
I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies
View Related
Jun 13, 2011
I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
View 3 Replies
View Related
Nov 20, 2012
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
View 2 Replies
View Related
Jun 19, 2012
LMS 4.2. I am receiving the alert below in my email inbox. It was my understanding that DFM would not send alerts for interfaces that are shut down. Is this a bug? [code]
View 2 Replies
View Related
Aug 9, 2012
I have 2 different network topology - network A and network B Both of them are connecting to the same gateway (a firewall) to the net. they're using the same range of public IP pool to NAT the private IPs. in shorts, all setup is almost the same except the devices' brand between A and B.I have no problem to access the webpage using network A. But whenever I attach the same laptop to network B, the same page won't display at all.I've done wiresharking to network B and the result shows "ICMP destination unreacheable (Communication administratively filtered)" which reported by unknown device (suspected to be the webpage's gateway).
View 5 Replies
View Related
Oct 31, 2012
I recently bought a bunch of cisco 3750-x switches. I configured them all and started deploying them. A day later, some of the switches started failing on me. When I connect the power cord to the AC main, the power supply module on the back shows "AC OK" LED Green but the "PS OK" LED shows Red. I started referring to the installation guide and it told me that "PS OK" LED turns RED when output has failed. Guessing this I checked with another power supply module that was working, but still I get the same LED indicators.The original power supply module works with other switches.IOS crash...?
View 5 Replies
View Related