LMS 4.2. I am receiving the alert below in my email inbox. It was my understanding that DFM would not send alerts for interfaces that are shut down. Is this a bug? [code]
View 2 RepliesI have been getting alerts on unused serial ports on my routers as being operational down. How can I stop these alerts?
View 5 Replies View Relatedread the posts regarding vlans that are administratively down, they suggested that they are down if no ports are assigned to them, however I do have a switchport assigned, and the interface is still down. This is on the vtp server and on the clients. The vlan is not listed when issuing show vlan brief. Other vlans configured in a similar way do show and their interfaces are up. These are two Catalyst 4948-10G.Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG5, RELEASE SOFTWARE (fc1).
View 5 Replies View RelatedI have a problem with the Cisco 881 router at one of our customers.It seems that after a "no shutdown" has been given on the Vlan interface, it still goes back to "administratevly down" after a reboot.So when I restart the router I always have to manually "no shutdown" the Vlan interface to come back up.While rebooting the router it also gives the following info in the console screen every time which is strange:
new interface Vlan1 placed in "shutdown" state.We tried several different firmware releases.
Replacing the router with a new Cisco 881 router did not work either. After they sent back the old Cisco 881 router we tested it here and there were no problems, we weren't able to replicate the problem.The configuration we use for the router is correct, we use it for hundreds of customers, so that can't be it either.The customer uses a fortinet firewall behind the router. Could it be that something inside the LAN of the customer that triggers the Vlan to shut down?
I have 2 different network topology - network A and network B Both of them are connecting to the same gateway (a firewall) to the net. they're using the same range of public IP pool to NAT the private IPs. in shorts, all setup is almost the same except the devices' brand between A and B.I have no problem to access the webpage using network A. But whenever I attach the same laptop to network B, the same page won't display at all.I've done wiresharking to network B and the result shows "ICMP destination unreacheable (Communication administratively filtered)" which reported by unknown device (suspected to be the webpage's gateway).
View 5 Replies View Relatedim having lms 4.2.2 and monitoring a cisco 7600 router interface ten gigabit ethernet x/x under dfm. When ever the interface is down due to any media issue i am not getting any alerts in dfm., the interface used to go down for more than 10 minutes. I am able to do an snmpwalk to this interface when the interface was down and getting the value as 2(for down). I am getting other information and configuration mode alerts in dfm for this device.
View 1 Replies View RelatedI am looking for a way to get CiscoWorks LMS 4 to send me an email alert when a switch port goers into a security violation (err-disabled).
View 2 Replies View RelatedSometimes we have unidentified traps in our log, we don't know where they come from.
In high severity faults we see an active alert with device name “Unidentified” event name unresponsive but with a certain ip address.
What are these alerts about? Can I filter them?,A second issue I have is that I get interface down alerts. But when we log on to the device, there is no interface down at all. We can also ping the device from the lms server at that time. I have been told that the admin state and operational state has to be up.
I will be configuring port forwarding to a phone system on the network for remote management. I would like to have the ASA send an email alert when a connection has been made to the open port. Is this possible to do and if so how to configure it.
View 1 Replies View RelatedCan I configure the 2504 to send email notifications for particular alerts? how?
View 2 Replies View RelatedUnder high severity Alerts Its showing following Error
An exception occurred.Please check the AAD.log file for further details.
AAD log shows This
22-Oct-2012|10:48:17.625|ERROR|AAD|TP-Processor6|DeviceManager|getHighSeverityAlerts()|.|com.cisco.nm.trx.afd.AlertRenderer.AFDException
[Code].....
From the WAP4410N admin pages or console you can enable e-mail alerts. You have to set the essential TO address and mail server address. Where can I put the FROM address ? From what I can see it uses the hostname value as from address. The hostname in my case is ap02. Then you could try setting a mail address in the hostname field, but thats not allowed.
[Code]....
On a Cisco ASA 8.4 code is it possible to receive an alert once a certain number of tcp/udp connections is reached? I'd like to see if I can get an email alert or syslog if the ASA reaches say 2,000 connections for example. Once I get an alert I could then investigate the cause of so many connections.
View 1 Replies View RelatedWe are getting below logs in our Syslog, how could i stop this."%ASA-2-106017: Deny IP due to Land Attack from 161.233.167.65 to 161.233.167.65 "
View 1 Replies View RelatedIs there any way to change the subject line of the email alerts that are sent? Right now mine are coming with the MAC address, date and time. I would like to remove the MAC address and date and time so that I can sort them into one folder when I sort my email by subject.
View 7 Replies View RelatedI've got router as vpn-concentrator which receives vpn site-to-site connections from 10 branches with cisco 881 and cisco 1941.I started cacti monitoring and found out that there are too many errors on interfaces.URL.
View 5 Replies View RelatedI have an ASA connected to 2 ISPs.I am using object tracking for the default route so only 1 path is used at a time. I have a L2L VPN setup going out interface A. I would like to configure a 2nd VPN going out interface B with identical parameters.
(ASA software 8.2)
crypto map PATH_A 1 match address outside_1_cryptomap
crypto map PATH_A 1 set peer 10.1.1.1
crypto map PATH_A 1 set transform-set ESP-AES-128-SHA
crypto map PATH_A 1 set security-association lifetime seconds 28800
crypto map PATH_A 1 set security-association lifetime kilobytes 4608000
crypto map PATH_A 1 set reverse-route
[code]....
We are using non-advertised IPs on many devices, but LMS is attempting to ping these addresses and setting off all sorts of security alarms. How to stop LMS 4.1 from pinging the interfaces? We don't even want LMS to do any fault monitoring so if that could be turned off, it would be even better.
View 1 Replies View RelatedI am trying to secure sub interfaces on a 2600 Router
interface FA0/1.1
No Access-group
Interface FA0/1.2
IP Access-group 110 out
Access-list 110 deny ip 2.2.2.0 0.0.0.255 1.1.1.0 0.0.0.255
Access-list 110 permit ip any any
This works but it blocks traffic both ways I only want to block one, I dont want FA0/1.2 to be able to access FA0/1.1 but I want all traffic to be allowed to go the other way
Does any know why the ASA will monitor physical interfaces by default, but monitoring of logical interfaces is disabled by default? Or better yet, is anybody doing a monitor-interface for a subint without issue? I'd imagine it isn't enabled by default for a reason.
View 2 Replies View RelatedI understand that IPv6 uses the MAC address of a LAN interface to make up the EUI-64 of a serial interface since serial interfaces don't have MACs. What happens when there is no LAN interface available? What if the switch has only serial interface cards?
View 2 Replies View RelatedI have a question, it is possible to have two WAN interfaces to configure a cisco 892 router with an ip 255.255.240.0 84.197.167.111 adderess of the first interface and a different ip address 84.197.174.182 255.255.240.0 on the second interface
View 5 Replies View RelatedI have a location where I have 2 WAN links, but without a dynamic routing protocol in between. I want to implement a kind of hub to 2 spokes VPN. But the spokes will actualy be on one single ASA firewall, each spoke on a different interface. One hub-spoke will be primary, the other one the secondary. When the WAN link for the primary VPN fails the secondary should be started on the hub to the other spoke.
View 1 Replies View RelatedI'm trying to get two Cisco 1941 routers with HWIC-1T and HWIC-3G-HSPA interfaces to use the 3G interfaces if the frame is down (as it is right now).In the lab, I was not able to get these to use the 3G interfaces as a backup (i.e. backup interface cell 0/1/0) and I've not been able to workout the correct incantation for static routing either.
kununurra#show ip int br d1
Interface IP-Address OK? Method Status Protocol
Dialer1 172.31.2.94 YES IPCP up up
[Code]....
I have been configuring the SG-300 28 from both web and cli interfaces.When doing a sh run I get Int gi2 before int Gi1? WTF?Also one of my vlans wasn't working on interfaces but was working through the assigned trunk port to my other switch.I deleted it and recreated it and it is now working. Why we have a failure and go to reconfigure a switch and have these same issues.
View 1 Replies View RelatedIn ASA 8.0,I have following queries related to redundant interfaces
a)While configuring redundant interface can the redundant interface again be divided into logical interface like red1.1 , red1.2 ?
b)Is Redundant interface supported in the Multiple context mode
on 3750X how many interfaces can be configured with PIM activated on ?
View 2 Replies View RelatedI've installed the ACS version 5.2 in a VMware platform and everything seemed fine but in the post installation task I need to access to the GUI. Based on the documentation I should access the "https://10.0.0.X/acsadmin" on my browser's url but after I hit enter nothing comes up, there's just a whiter web page. Is there any missing configuration that I need to do and that it is not on the configuration pages?
View 5 Replies View RelatedIs there a limitation to the amount of sub-interfaces that can exist on a Cisco 6509? The switch has WS-SUP720-3B (Sup card), WS-X6724-SFP (linecard), and 12.2(33)SXH7 (IOS).
View 7 Replies View RelatedIf I have a PI 1.2 system that has multiple interfaces configured I can upgrade to PI 1.3 and both interfaces remain and I can see both under the admin webpage under appliance interfaces. But if I do a fresh install of PI 1.3 I can only configure one interface. The commands fail from the cli to configure anything but gigabitethernet 0. Are multiple interfaces not supported in PI?
View 2 Replies View RelatedI have two vlan interfaces, how to limit bandwidth on them ?I need than speed on each will be direrent.
View 1 Replies View RelatedI have 1841 router with 2 serial Wan interfaces each one is 2 Mbps. i want to configure them to use all of 4 Mbps.How to Configure them.
View 8 Replies View RelatedMy problem includes little bit design issue.I have site2site vpn between customer and my cisco router.But the customer wants to add L2TP traffic in this site2site tunnel.I have no experince about L2TP tunneling.I have also ASA 5500 series which locates behind the Cisco router.ASA interfaces have not public IP.Question is that Can I use my ASA firewall for just L2TP tunelling?Every document says ASA use IPSEC over L2TP. But IPsec tunneling is already done by Cisco Router. Or should I have to do both tunnel in same network device? I mean ASA or Router?
View 1 Replies View Related