I have a question, it is possible to have two WAN interfaces to configure a cisco 892 router with an ip 255.255.240.0 84.197.167.111 adderess of the first interface and a different ip address 84.197.174.182 255.255.240.0 on the second interface
View 5 RepliesI have an ASA 5505 with 3 host license.I want to configure 2 outside interfaces and have inside interface. The outside interface going to a separate ISP.Will this work or do I need more licences?
View 3 Replies View RelatedGot new ASA5550, code 8.2.2 in flash, can't configure "nameif" or "ip address" on the interfaces: [code] These are all the options that I get! Another weird thing I noticed is "<system>" string in "show ver" top line: [code]
View 2 Replies View RelatedI have a cisco ASA 5520 that i'm configuring.From the actual Firewall (with is a linux server), we have the outside interface eth0 with has a public IP and other sub-interfaces (eth0.1; eth0.2,...) with others publics IPs.I'd like to know how I can configure it in an ASA
View 7 Replies View RelatedI have a pix515 v6.3.3. Is it possible to configure dual ISP on two interfaces and have redundancy between them?
View 1 Replies View RelatedI have WLC 2504 controller and six access points AIR-LAP1042N. I reading Cisco 2500 Series Wireless Controller Deployment Guide url...trying to set up along the lines.
It is also possible to have multiple AP-managers in a different subnet than the management interface. However, in this case, it is recommended that you disable the AP-manager from the management interface and create another AP-manager interface on different physical ports in a different subnet than the management interface. All multiple AP-managers in this scenario should be in the same subnet.
I maping management interface on physical port 1 and disabled ap-manager on it. Set up 192.168.7.0 subnet with non tagged vlan. This iface/port I want to use only for access to WLC web-interface. Then I create dynamic interface ‘dynamic1’, map him on port 2, enable ap-manager on him, and set up 192.168.110.0 subnet with vlan 10. Then I tryed map wlan1 to this iface, but I can’t because in the choice was only management iface to map wlan1.
There is three dynamic interfaces on same subnet and vlan, in example above. But when I try to add dynamic iface with the same vlan/subnet as an existing dynamic interface, I get an error, and can’t adding.
On a 3750 switch, is it possible to configure jumbo frames only on certain interfaces and leave the other ones as they are?
View 9 Replies View RelatedI have a an ASA 5520 connected to a Layer 3 (3750) switch (Inside) and a connection to a 2960 switch (Outside) to get to the internet. . I have created vlan interfaces on the 3750 switch and enabled ip routing on the switch to enable the vlans to communicate with each other.
Vlan Interfaces on the switch:
Vlan 100 172.17.1
Vlan 200 172.18.1
Vlan 300 192.168.3.1
I want the devices connected to the 3 vlans to be able to pass through the firewall and get out to the internet.I have connected the ASA to the 3750 by routed interfaces (10.10.10.1) --------- (10.10.10.2) and they are able to ping each other.I have also put a default route on the 3750 sending all traffic from the switch to the ASA inside interface (10.10.10.1)The issue that i am having is that the ASA also connects to a 2960 which has a connection to the Internet, and they are handing off an ethernet connection from the 2960 that sits in VLAN 55 (Vlan 55 is the Internet accessible vlan).How do I configure my ASA to send all traffic from my (3) vlans to the interfaces that connects to the 2960 switch?
I'm trying to set up an 1801 router with two WAN interfaces, fastethernet0 and fastethernet1. On the LAN side, I have two subnets. One subnet's internet traffic should be routed over fastethernet0, the other over fastethernet1.I've setup some route maps to accomplish this. I can surf the internet using subnet 192.168.2.0/24 fine, all traffic goes out of fastethernet0. However, and this is where the problem is, if I try to reach the internet using subnet 192.168.3.0/24, all packets go out interface fastethernet0 with the source address of fastethernet1!When I'm surfing the internet, from subnet 192.168.3.0/24, packets should be going out fastethernet1, now they're going out fastethernet0.
View 8 Replies View RelatedCustomer has three 881 routers. FE0 connects to their WAN, FE4 connects to their LANs. Two VLANs are configured on FE4. Class-maps and Policy-map created to detect voice traffic:
class-map match-any VoIP-RTP-Trust
match ip dscp ef
class-map match-any VoIP-Control-Trust
[Code]....
configuring my Cisco 2951 router. There are three routed interfaces that I need to configure: one for the internal LAN, the second for another private subnet that connects to a Data Centre and the third for the WAN connection. I have configured the Ge0/0 interface as the LAN interface with the internal network 10.17.0.0/24. I have also configured my WAN interface Ge0/1 for internet connectivity. Now, I need to configure the third interface Ge0/2 that will connect to the Data Centre. This will be a private point to point switched ethernet link. The Data Centre will host a secondary domain controlller. So, I want it to be on the same network as the internal LAN, i.e., 10.17.0.0/24. I want to be able to see all other devices that will be located at the Data Centre just like I would see all devices connected to the internal LAN.The problem I am facing is that Cisco 2951 does not allow me to configure two routed interfaces to be on the same subnet. Is there any way to work around this problem and configure both the internal LAN and the Data Centre private network to be on the same subnet.
View 6 Replies View RelatedI have a 1921 with 3 interfaces. One for the LAN and the other 2 are wan each with a public address. The 2 wan interfaces are used for redundancy. I would like to know how I can static nat the same port and inside address on both wan interfaces.So if the request comes in on one or the other it works. I know if I do a static nat to one of the wan interfaces and then add the same port and inside address to the other wan interface it replaces the previous configure.
View 5 Replies View RelatedI have a Cisco 2811 router with 2 ADSL interfaces and we have 2 internet lines associated with it. One is with Telstra and one is with iiNet. All internet traffic from inside the office is routed through Telstra line. The iiNet line is used for incoming emails, establishing VPN etc. The problem is that we are not able to "PING" the iiNet's IP address from the outside world however, PING works for Telstra IP. What do I need to configure on the router if I want to PING and Putty in the router using both Telstra's and iiNet's IP from outside world?
View 1 Replies View RelatedWe have just installed our first 2951 router, and were suprised to see in our Netflow collector that Tunnel interfaces appeared even though we did not configure any, I have seen other posts talking about PIM tunnel when using Multicast, but we dont use multicast and the tunnel is GRE questions are, where do these interfaces come from? how do they pick up an IP address? can we shut them down? IOS is 150-1.M4 loopback interface ip address is 172.16.224.238 ( tunnel source) see output from sh int below
Tunnel0 is up, line protocol is up Hardware is Tunnel Interface is unnumbered. Using address of Tunnel1 (172.16.0.1) MTU 17912 bytes, BW 100 Kbit/sec, DLY 50000 usec, reliability 255/255, txload 99/255, rxload 1/255 Encapsulation TUNNEL, loopback not
[Code]......
We currently installed a 100Mbps fiber line with Ethernet hand-off. I purchased a Cisco 3925 ISR to be the gateway for this connection. I am not going to use it for any security purposes. I have an ASA5520 that will do that work. Right now I am currently just trying to get the router online.
I know the following
Laptop <--->GB 0/1((()))GB0/0<---->Ethern
et handoff from ISP.
I can ping and SSH to the outside interface of the router from outside the network. I can also ping and SSH to the router from the laptop that is directly attached to the routers GB0/1 port. From the Router's CLI I can ping IP addresses on the internet. From the laptop I can not. I can not access the internet through the router though. Here is my config.Building configuration...
Current configuration : 3724 bytes!! Last configuration change at 02:17:03 UTC Tue Jan 15 2013 by ggsis! NVRAM config last updated at 02:09:33 UTC Tue Jan 15 2013 by ggsis! NVRAM config last updated at 02:09:33 UTC Tue Jan 15 2013 by ggsisversion 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname XXXNAMEXXX!boot-start-markerboot-end-marker!!logging buffered 51200 warningsenable secret 4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX!no aaa new-modelmemory-size iomem 20!no ipv6 cefip source-routeip cef!!!!!no ip domain lookupip domain name XXXXXXXXXXXXXXDomainXXXXXXXXXXXmultilink bundle-name authenticated!!crypto pki token default removal timeout 0!crypto pki trustpoint TP-self-signed-XXXXXXXXXXXXXXXXenrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-XXXXXXXXXXXXXrevocation-check nonersakeypair TP-self-signed-XXXXXXXXXXXXXX!!crypto pki certificate chain TP-self-signed-XXXXXXXXXXXXXXcertificate self-signed
[code]...
I have a Cisco router C1700 and it is presenting unknow errors on Serial 0/0 and fa0/0 interfaces. Why this counter is increasing?? Im not very sure if is by CDP neighbors or Vlans that are not configured on a switch attached.I undertand that the unknown protocol drops field displayed in the above example refers to the total number of packets dropped due to unknown or unsupported types of protocol. How to solve this unknown DROPS? [code]
View 4 Replies View RelatedI need to bridge 2 subinterfaces; F0/0.301 and F0/0.302 on a single router.The router interfaces with a Cisco 2960 (LAYER-2) switch.QUESTION is, does a Cisco router support bridging on subinterfaces on the same physical interface?Currently this is NOT operational Spaiing-tree on F0/0.301 and F0/0.302 is down, switch side is forwarding for both Vlans.show ip interface brief shows up/down status of F0/0.301, F0/0.301 and BVI6 is down/down?
:
SETUP:
bridge irb
!
!
Interface F0/0
no ip address
[code]....
I am trying to add WCCP to be configured for websense. My first option seems to be either purchase an IPServices license for the stack of 3750E switches, but i am thinking this will require us to license all three switches in the stack. The second option i am looking at is to do the WCCP configuration on the 2800 router we have on the edge. The problem is both Gig ports are in use, one going to the firewall and the second going to the ISP. My first question would be, which option is better in terms of manging as well as cost of implementing it.The second question is, if WCCP on the router is a better option, what is the add on module i should be looking to get to add the additional ports to hook up the Websense cache.
View 8 Replies View RelatedI am wondering if xconnect L2TPV3 feature could be done on multiple SVI interfaces on 871 router and 2911 router with built in 8 port switch?Like I need to extend two ethernet interfaces and can I use two SVIs on router built-in switch module on each side?
View 2 Replies View Relatedi have a question about multiple TACACS Groups. I want to archive the following:
A Cisco 888 is managed by me and a Provider Support Team. Since we both want to access our own TACACS Server, i want to create two TACACS Groups. Is it possible to me, to bind a Tacacs Group to one Interface, and the second TACACS Group to another ? Means that our stuff is connecting to the LAN Interface FastEthernet0 that is applied to the SVI in V LAN 1.
The service technicians from the Provider are connecting to the external Interface or through a possible Lo. (another IP). I do not want to mix our 2 TACACS+ Server and theirs together in one Group. So have anybody tried this before ?
The ASR1000 router supports hot-swap modules and network interfaces?
View 2 Replies View Relatedwhat is a maximum number of configurable gre tunnel interfaces on CISCO2921-HSEC+/K9 router?
View 2 Replies View RelatedI have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
I've got router as vpn-concentrator which receives vpn site-to-site connections from 10 branches with cisco 881 and cisco 1941.I started cacti monitoring and found out that there are too many errors on interfaces.URL.
View 5 Replies View RelatedI have an ASA connected to 2 ISPs.I am using object tracking for the default route so only 1 path is used at a time. I have a L2L VPN setup going out interface A. I would like to configure a 2nd VPN going out interface B with identical parameters.
(ASA software 8.2)
crypto map PATH_A 1 match address outside_1_cryptomap
crypto map PATH_A 1 set peer 10.1.1.1
crypto map PATH_A 1 set transform-set ESP-AES-128-SHA
crypto map PATH_A 1 set security-association lifetime seconds 28800
crypto map PATH_A 1 set security-association lifetime kilobytes 4608000
crypto map PATH_A 1 set reverse-route
[code]....
We are using non-advertised IPs on many devices, but LMS is attempting to ping these addresses and setting off all sorts of security alarms. How to stop LMS 4.1 from pinging the interfaces? We don't even want LMS to do any fault monitoring so if that could be turned off, it would be even better.
View 1 Replies View RelatedI am trying to secure sub interfaces on a 2600 Router
interface FA0/1.1
No Access-group
Interface FA0/1.2
IP Access-group 110 out
Access-list 110 deny ip 2.2.2.0 0.0.0.255 1.1.1.0 0.0.0.255
Access-list 110 permit ip any any
This works but it blocks traffic both ways I only want to block one, I dont want FA0/1.2 to be able to access FA0/1.1 but I want all traffic to be allowed to go the other way
Does any know why the ASA will monitor physical interfaces by default, but monitoring of logical interfaces is disabled by default? Or better yet, is anybody doing a monitor-interface for a subint without issue? I'd imagine it isn't enabled by default for a reason.
View 2 Replies View RelatedI understand that IPv6 uses the MAC address of a LAN interface to make up the EUI-64 of a serial interface since serial interfaces don't have MACs. What happens when there is no LAN interface available? What if the switch has only serial interface cards?
View 2 Replies View RelatedLMS 4.2. I am receiving the alert below in my email inbox. It was my understanding that DFM would not send alerts for interfaces that are shut down. Is this a bug? [code]
View 2 Replies View RelatedI have a location where I have 2 WAN links, but without a dynamic routing protocol in between. I want to implement a kind of hub to 2 spokes VPN. But the spokes will actualy be on one single ASA firewall, each spoke on a different interface. One hub-spoke will be primary, the other one the secondary. When the WAN link for the primary VPN fails the secondary should be started on the hub to the other spoke.
View 1 Replies View RelatedI'm trying to get two Cisco 1941 routers with HWIC-1T and HWIC-3G-HSPA interfaces to use the 3G interfaces if the frame is down (as it is right now).In the lab, I was not able to get these to use the 3G interfaces as a backup (i.e. backup interface cell 0/1/0) and I've not been able to workout the correct incantation for static routing either.
kununurra#show ip int br d1
Interface IP-Address OK? Method Status Protocol
Dialer1 172.31.2.94 YES IPCP up up
[Code]....
I have been configuring the SG-300 28 from both web and cli interfaces.When doing a sh run I get Int gi2 before int Gi1? WTF?Also one of my vlans wasn't working on interfaces but was working through the assigned trunk port to my other switch.I deleted it and recreated it and it is now working. Why we have a failure and go to reconfigure a switch and have these same issues.
View 1 Replies View Related