Cisco Switching/Routing :: C3750 SFP Failure After Reload
Mar 11, 2013
I have a cable from an SFP module in a WS-C3750-48P with 12.2(55)SE1 running to a Gigabit port on a Cisco WLC. After the switch recovers from a power failure, the gigabit autonegotiation fails. The cure is a long drive to unplug and reseat the SFP. Note this happens at too many similar sites for this to be a loose connection. Interface shutdown then 'no shutdown' is not sufficient. The state is 'line protocol is down (not connected)'. Interface is configured for switchport mode trunk (auto speed, auto duplex). Command 'switchport nonegotiate' makes no difference. Is there a more powerful command than 'shutdown' which might toggle the interface signals? Is there some way of resetting the SFP? sh int gi 1/0/1 displays 'media type is 10/100/1000BaseTX SFP' and zero packets received.
View 4 Replies
ADVERTISEMENT
Dec 12, 2012
I've just purchased a new Cisco 881.I'm using NAT NVI for my inbound static mappings. However, regardless of the fact that the config is saved to nvram, after a reload of the router, the NAT mappings are setup as traditional inside/outside mappings. This means that inbound connections in to the router on the required services fail, until someone logs on to the router and re-applies the NVI mappings.
Here's a sanitised version of my startup-config:
!
! Last configuration change at 20:20:15 UTC Tue Dec 11 2012 by xxx
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code].....
View 20 Replies
View Related
Nov 29, 2012
SSH has been enabled on our one and only 4507 switch for several months and working fine. A few weeks ago the switch had to be reloaded and when it was back online I couldn't SSH to it. When I connected via the console and typed "show ip ssh" it came back saying I needed to generate the keys. Did that and it starting working again. The same switch had to turned off and on the other day due to a power down in the server room and when it came back the same thing happened again!!
The version of IOS is: cat4000-i5k91s-mz.122.20.EW
View 1 Replies
View Related
Feb 26, 2012
Last night, the C6509-E do a unexpected reload. In the crashinfo, I can see that the last error message before the reload, was as follows: %C6K_ PLATFORM-SP-2-PEER_RESET: SP is being reset by the RP
I consulted the cisco website about this error message and what I found was the following:C6K_PLATFORM-2.
View 1 Replies
View Related
Feb 21, 2013
I have a problem to solve in our data center, see attached drawing. HW: Our core switches consists of two stacked C3750 with ip routing. What I want to do is probably simple but I haven't been able to figure out the best method.
VLAN10 and VLAN20 should not be able to communicate with each other. (ACLs?)VLAN10 will have it's own default route/firewall. Both VLAN10 and VLAN20 should be able to send server backups to server in VLAN30. All 3 V LANs come in on a trunk from a pair of stacked C2960-S. I need it to be able to scale if we have 50 VLANs for instance, hopefully without long complicated ACLs. I've been considering VRF's, PBR but can't decide what's the simplest solution to this problem. I have never done this before so I would prefer to start off on the right foot.
View 1 Replies
View Related
Mar 9, 2013
We have a backup sup 720 which has a 2 gigabit ethernet though port channel, to another chassis. Suddenly UDLD detected an error and got into err disable, then this err disable didn't let the interface set to DOWN, and created a switch loop, then our Supervisor reloaded. I'd like to know what could have caused this reload. In my opinion could have a been the switch loop, but also I've been checking from the output interpreter the show tech and might have been a bug, the only one that could match in IOS version 12.2(33)SXH, is this one: url...
We're going to disable err-disable next time I guess and recover the link manually, apart from that what could have made the sup for crash and reload?
View 4 Replies
View Related
Jul 31, 2012
Suffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?
View 1 Replies
View Related
Dec 15, 2012
while i am configuring a port on switch .The switch reloads.After reload the show version says
System returned to ROM by bus error at PC 0x458F6C, address 0x0
show version from the effected switch is
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[cODE].....
View 2 Replies
View Related
Jun 3, 2012
Our router suddenly reloaded. Below are the crashinfo obtained:
1st crashinfo:
7606_Router#more sup-bootflash:crashinfo_20120604-02260500:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
[code]....
We are running s72033-advipservicesk9_wan-mz.122-18.SXF9
View 14 Replies
View Related
Feb 19, 2013
I have a problem with the Cisco 881 router at one of our customers.It seems that after a "no shutdown" has been given on the Vlan interface, it still goes back to "administratevly down" after a reboot.So when I restart the router I always have to manually "no shutdown" the Vlan interface to come back up.While rebooting the router it also gives the following info in the console screen every time which is strange:
new interface Vlan1 placed in "shutdown" state.We tried several different firmware releases.
Replacing the router with a new Cisco 881 router did not work either. After they sent back the old Cisco 881 router we tested it here and there were no problems, we weren't able to replicate the problem.The configuration we use for the router is correct, we use it for hundreds of customers, so that can't be it either.The customer uses a fortinet firewall behind the router. Could it be that something inside the LAN of the customer that triggers the Vlan to shut down?
View 1 Replies
View Related
Oct 13, 2009
I have a Catalyst 4500 WS-C4506 and S-X4516-10GE Supervisor running under IOS 12.2(52)SG IP BASE SSH. After having installed IOS 12,2(53)SG i wanted to schedule a reload. After entering the reload at command I get the message %Reload in Progress and nothing happens.
View 4 Replies
View Related
Sep 12, 2010
I have the following problem with
Situation:
- 2x 3750G-12S Distribution-Switches (DS) and several 3560/2960 Access-Switches (AS)
- redundant Fiber optic uplinks between AS and DS
- Cross-Stack Etherchannel config on all uplinks
- UDLD aggressive mode configured on all uplinks
Problem:
- when I reload the DS and the switch comes up again, I've lost the connection with several (not all) AS
- looking at the AS log I found the following error message: "%UDLD-4-UDLD_PORT_DISABLED: UDLD disabled interface Gi0/1, aggressive mode failure detected"
Cause:
- in the log of the AS I don't see intf Gi0/1 go down during the reload of the DS
- this means the DS didn't shuts down all its ports during the reload
- but this also means that UDLD on AS didn't know about DS reload, and therefore didn't resets counters
Workaroud/Solution
- I'm now configuring errdisable recovery on all AS
So I'm forced to configure errdisable recovery, even if I don't want.
View 3 Replies
View Related
Jul 10, 2012
I would like to test the possibility to reload devices via SNMP for new switches like 2960, 3560 and so on.I know that the command "snmp-server system-shutdown" has to be configured, then I need to send the set query to the device via SNMP.
I have found on the net the OID 1.3.6.1.4.1.9.2.9.9.0 but it belongs to an old MIB and doesn't seem to work with new switch models.
View 4 Replies
View Related
Nov 6, 2011
I have WS-C3750-24PS version 12.2(55)SE4. I am configuring PBB VPLS. MY PE/P routers are alcatel 7710/7750
my topology is like that.
CE1<-------> Provider_switch(3750)<-------> PE1 < ----IP/MPLS----> PE2<-------> Provider_switch(3750)<----------->CE2
16 11 11
[Code].....
View 3 Replies
View Related
Mar 30, 2013
I am having troubles to get 2 C3750-X switches WS-C3750-X-48P-L) to stack. They are both running iOS 15.0(2)-UNIVERSALK9, and are licensed for IP Base.
If I connect stack port 1 of switch 1 to stack port 2 of switch 1, and stack port 1 of switch 2to stack port 2 of switch 2 I get the following:
WS-C3750-X_STACK1_SW1>show switch stack-ports summary
Switch#/ Stack Neighbor Cable Link Link Sync # InPort# Port Length OK Active OK Changes Loopback Status
[Code].....
I have tried restarting (powering off for about 1 min and turning back on) simultaneously, and powering off switch 1 for 1 min and switch 2 for 2 min. I have also tried both enabling the stack ports, and disabling followed by enabling.
View 1 Replies
View Related
Jan 2, 2008
I have this system: IOS (tm) C3750 Software (C3750-I5-M), Version 12.1(19)EA1d, RELEASE SOFTWARE (fc1
An error appear in console (many times in one minute):
Jan 3 16:25:37: %LINK-3-BADMACREG: Interface StackPort1, non-existent MACADDR registry for link 0
-Process= "<interrupt level>", ipl= 4
-Traceback= 20A364 187F04 58D6FC 58B950 2D7CE0 2E00C8 2E2BEC 2E2F24 2B0BF8
What is the problem? What is the solution?
View 2 Replies
View Related
Jun 6, 2012
I would like to apply policing on a C3750 interface, for all traffic matching 10.0.0.0 / 8, except for sub net 10.0.0.0 / 24. I plan to apply the following configuration, with an ACL that denies 10.0.0.0 / 24 then accept 10.0.0.0 / 8. I am quite sure of the answer but need a confirmation about the following configuration correct ? (10.0.0.0 / 24 will be not blocked, and no policing will be apply on it?)
ip access-list extended TEST
deny tcp 10.0.0.0 0.0.0.255 any eq 5000
permit tcp any 10.0.0.0 0.255.255.255 any eq 5000
[code]....
View 2 Replies
View Related
Nov 21, 2011
I have a stack of 2 C3750-switches (WS-C3750G-24TS-1U) with IPBASE-firmware (12.2(52)SE).
When I ping to a machine (in this case a virtual one), the replies are always received on the port where the machine is connected, but on the port-channel connecting to the stack of the 'pinging device' the reply comes only for certain initiators, and not for all.
Setting:
Gi1/0/6: Device/Server I want to connect too ; defined as access port
Gi1/0/25 + Gi2/0/25, as Port-Channel 1: The location of the devices I connect (read as: the uplink to the stack of the PC's), defined for Dot1Q-trunking
Monitoring setup: Source ports: Both: Gi 1/0/6, Po1 (or Po1 replaced by both interfaces)
For the machines which can ping the server I see 2 echo (ping) requests, followed by 2 echo (ping) replies ... So once seen on the Po1, and once seen on the interface Gi1/0/6.
However for other machines, the 2nd reply is missing ; which must be caused by the dropping of these packets in the switch. At least, I my opinion this must be the reason... But I can't see any (change of) output drops at int Po1, nor at Gi1/0/6. The CPU doesn't seem to have high usage, and even then, I don't think the error would be constant, as it's always failing for some PC's, and never for others... (at least for a certain time, a few hours it can be constant, the problem dissapears from time to time).
View 1 Replies
View Related
May 3, 2013
I am not able to find the exact bug for Cisco 3750E stack - Debug Exception (Could be NULL pointer dereference) Exception (0x2000) error. Closest i can find is CSCsa72400 which only affects ver 12.2(20)SE4.All the stacks (3 switches) are running 12.2(50)SE3, It appears that the switch 1 crashed and reloaded. My hunch is its software but i cant find any related bugs. It could be hardware issue as well ?
View 4 Replies
View Related
Apr 5, 2012
I have just upgraded 2 3750 switches in a stack via the master and reloaded the master switch remotely, how can I reload the 2nd (member) switch?
View 16 Replies
View Related
Nov 7, 2011
I uploaded a new config file via TFTP to a 3560 switch. What are the order of commands to get it to boot from this new config file instead of the file listed in 'sh boot': [code]
View 7 Replies
View Related
Mar 13, 2011
We have existing stack of 3 units of WS-C3750-48TS-S ( 100 mbps ports with Gigabot uplinks). with IOS as follows, Can we add WS-C3750G-48PS-S in this same stack (this is 48 Gigabit ports)?
View 2 Replies
View Related
Jun 13, 2013
We have several of these WS-C2960S-24PS-L running 12.2(55)SE5 C2960S-universalK9-M and need to upgrade to a better.IOS since we have a sitution where CPU would get to 100% but we have only a few ports connected.Also we have several of WS-C3750-48P running 12.2(55) SE6 C3750-IPBASEK9-M.
View 3 Replies
View Related
Feb 4, 2013
According to cisco manual in order to change SDM template i need to reboot switch, but when i have C3750-X stack do i need to reboot stack or maybe will be enough reboot in sequence the stack members?
View 3 Replies
View Related
May 9, 2013
We are deploying the ISE MAC address authentication by-pass (mab) feature in our network as an alternative to port security on the switch port. Works well except for certain devices e.g. printers, snmp modules, and Unix/Linux Operating systems which can range from 5-10 minutes to never in authentication/opening the port.
View 2 Replies
View Related
Feb 3, 2012
can i stack cisco (ws-c3750G-12s) with (ws-c3750X-24p-poe-s) with (ws-c3750-48p-10/100 poe) i mean even a switch is 10/100 and the other switch is 10/100/1000?
View 3 Replies
View Related
Sep 30, 2009
Is it possible to upgrade a c3750-stack one member at a time to avoid downtime? I need to keep L3-functionality up.
If I have one etherchannel from access-switch (2 channel-ports in 3750, in different stack-members), my 3750-stack as a distribution layer switch, and another etherchannel (also spread over multiple stack members) to core, can I upgrade the entire stack without traffic interruption?
View 5 Replies
View Related
Aug 7, 2008
We have a bunch of switches that are running fine but the running-config file is missing and we can't save the config to the tftp server. IOS is c3550-ipbasek9-mz.122-37.SE1. I've got lots of these switches running the same code that are just fine.
View 8 Replies
View Related
Nov 27, 2012
a) I have three C3750-X switch stack together as my SAN switch and running on the new 15.0 release which is 15.0(1) SE.
b) Recently the master switch rebooted without any explanation. Create ticket with TAC and got an answer that it is due to a bug with ID: CSCtr31957.
My question is, which release that should i choose either the 15.0(1) SE3 or the latest 15.0(2)? Will it affect any of my configuration if i change to 15.0(2)?
Finally, what is the best practice to upgrade IOS in a stack whether to upgrade it 1 switch at a time or do it to all at once?
View 3 Replies
View Related
Apr 22, 2012
I have one 4506E switch working in Lan setup as a core switch with WS-X45-SUP6L-E running ipbase IOS 12.2(54)SG1. Each time after reload the switch we found that the clock is getting reset ( time is getting changed ) where as day, date & year is unchanged.
View 2 Replies
View Related
Feb 13, 2012
Is that possible add WS-C3750-48TS-E to ws-c3750e-48td stack?
View 4 Replies
View Related
Jan 1, 2012
I have 8 switch stack consisting of six WS-C3550-48P and two WS-C3750G-16TD running software vesrion 12.2(25) SEB1. When I added new C3750v2-24PS (running image 12.2(50) SE5) in stack so I up-graded the image of existing 8 switches with latest veriosn 12.2(50) SE5. Once I have done with the upgrade then all ports of my stack switches went down after around five minuts. Is it image compatibility issue with existing switches or something else?
View 7 Replies
View Related
May 19, 2013
Our client having one c3750 with ipbase license switch.They are connected server and end switches to that switch.Our customer want to increase the speed to accessing the server at that time I am told to use etherchannel.Customer happy about this and implement the etherchannel configuration.Now i need to configure etherchannel upto 4 physical link.server are connected on port no Ge1/0/10,they want to bind four phical link GE1/0/10-13.how to configure etherchannel in this switch?
View 1 Replies
View Related
