Cisco :: ASR1002 SNMP Statistics For GRE Tunnel Interface Statistics
Mar 28, 2013
We use Cacti to get interfaces statistics of a ASR1002 router (version 03.04.02.S.151-3.S2).A new GRE tunnel has been created, but unfortunately we are not able to get basic interface average during the day.What is surprising is the fact the graphs are built on the night only.
It seems as soon as we exceed some level of Bandwidth (~ 700-800k) the tool does not get the information.The OID I try to get are ifHCInOctets (.1.3.6.1.2.1.31.1.1.1.6) and ifHCOutOctets (.1.3.6.1.2.1.31.1.1.1.10) and some other interface statistics for both 64 and 32 bits. [code]
I have the Cisco EPC3825 EuroDocsis 3.0 Gateway and i cannot get statistics from this modem on snmp. Use snmpwalk. Nothing was found in settings of device.
I am interested in gathering cumulative threat-detection statistics from an ASA running 8.3, and displaying number of attacks over time. I am already capturing traffic information via netflow, but am interested in getting threat information.
Is there a way to capture the statistics via SNMP or any other method?
I have recently installed prime lms 1.3 and added several switches to be managed. Is there at this moment a possibility to display port statistics and network statistics for the wired part of the network? I am used working with LMS, but features like the topology view, with bandwidth usage is not yet integrated in Prime Infra it seems. Is there anything to monitor the wired network in Prime Infra 1.3.
I took a switch and connected it to my LAN switch is 2960 with LanBase image and PoE on it I have 3 interfaces in up state - 2 interfaces with cisco phones (6921 and 9951) nad 1 interface as uplink
I have a little problem...I want to see the maximum tcp connections that I had on my Cisco. I tried using show ip statistics but it's not working. I have a Cisco Catalyst 3750G (WS-C3750G-48TS)
Region : India Model : TL-WR740N Hardware Version : V4 Firmware Version : 3.12.11 Build 120320 Rel.51047n ISP : BSNL
how to get a graph of the router statistics like upload and download speeds - both total and per device? Something like MRTG. The closest I came to getting data from the router was with RouterStats-Lite, but I was unable to get it to work.
I'm running v4.3.5 in our WAAS environment. At the CLI of one of our 7341 WAEs, there are several connections that show up [code] However, in the Central Manager nothing shows up - not even empty graphs - when I click on a device and go to monitor/connections statistics. After a few minutes, I do get an error message that states "Error retrieving connection stats. Please ensure that the device is online and then refresh." By the way, I get all other statics in the GUI such as Optimization Details Report, Traffic Summary Report, etc. Another thing, these WAEs are behind a router and supposedly the ports to allow access to/from the WAEs and other data is allowed through the firewall.
Is there some special port that needs to be opened on the firewall to allow for 'connection statistics' information displayed, that doesn't need to be opened for the other statistics to display? Or could this be a bug in the software?
I have an E2500 router, running the latest firmware 1.0.7.
Where or how can i see which is the machine (mac or ip) that is doing more traffic, in fact i would like to see what computers are doing how much traffic.
This is a default on most routers, its so weird to not been able to find this on a Cisco product.
I have users connected to a 2960-S running 12.2(53r)SE complaining of slow network, specifically Internet performance while the upstream 2960 on the same vlan has no such issues, so I don't suspect link congestion on the face of things.I'm planning on upgrading the code, but wanted to see what could be checked first. I'm seeing some drops but could use some tips on how to proceed from here as to what might be the issue. CPU is under 10% whenever I check it.
*osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/927/stat.(erno 24) *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED: osapi_task.c:3431 Failed to retrieve statistics (/proc/<pid>/stats) for task 'gccp_t' *osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/926/stat.(erno 24)(code )
when present this loggs the device present those symptoms:
lost GUI session Lost console conection Lost SSH and Telnet conecction the WLC 4404 not work is stopedd
Six month ago I installed and configured a wireless mesh with the equipment named. From two weeks ago one AP (MAP) restarts every day. In Wireless Lan Controller appears this logs:
"Unable to find AP entry in the database, could not process statistics information"
We have an ASR1002 with asr1000rp1-adventerprisek9.03.05.01.S.152-1.S1.bin software.I couldn't find any documentation on how to attach an L2 interface, in my case a subinterface with a single dot1q vlan, to a BDI interface.I'm able to create a bridge-domain interface but it's down down.The command bridge-domain on the subinterface url...
I have a requirement to provide stats on a per-department, per-destination basis between sites. If I take Voice as an example I have 5 child classes referring to the 5 departments each matching EF and a particular access-list that matches the department's subnet. I tie these 5 child classes into a parent Voice class-map.
Now when I issue a "show policy-map interface" command I see stats for the parent class-map only whereas I would expect to see a breakdown for each of the child classes which is what is required.
I'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
I am trying to monitor my ASA 5505. This asa is connect via a ip-sec tunnel to our network. I have no problems with snmp monitoring devices behind the ASA, but when trying to monitor the asa itself I do not get a SNMP response.
I am getting these unwanted entries on my syslog server.03/10/2012 12:57:48 172.21.113.20 Error 23898: Interface FastEthernet0/1, changed state to downI tried to stop them with no snmp trap link-status but it hasn;t worked.[CODE]
I'm familiar with snmp-server views and excluding certain mib's, but is it possible to permit an snmp host to poll just one interface and nothing else on the router?
I have a cisco 1841, Im trying to write an app which will get the Interface Utilization on my 2 atm interfaces and fast eth 0/0 interface.
I’ve been reading up and have got as far as downloading the codeplex snmp library project. I’m using the snmpget app to get details off my 1841 successfully, but I now need to know the OID for interface utilization and how to define which interface to get.
i have a Problem with SNMP on the ASA Outside Interface. I want to monitor the Interface via SNMP (linkup, link down). I have a Active/Passive Cluster running on 8.4.2 and configured SNMP (v1) for Test on the Outside Interface. It's not that hard but when i try to test my Configuration with (peerless) SNMP Tester the Interface doesn't respond. Did i forget to configure something? Searched the forum but didn't find anything useful.
MIB OID and the values.also i want to know the values og output packet and output packet drops MIB OID values of POS interface on GSR router (12000).because i am getting many output packet drops on these pos interface.how do i get these values from the router.
I am attempting to monitor bandwidth utilization of the WAN port for the RV180 via SNMP and I am getting strange results. If a 256MB file is transferred from a remote server (without compression), the ifInOctets counter doesn't increment by anything resembling 256MB:
I'm reasonably certain that the .5 interface is the WAN port based on the value of ipAdEntIfIndex.X.X.X.X, but even if that were not the case, none of the other interfaces increment by a value close to the amount of data transfered. SNMP monitoring of a WAP121 on the same subnet returns expected results. I can only assume that SNMP on the RV180 is completely broken.
The router has the latest firmware available (1.0.1.9). There is only one network connection and the RV180 is the default gateway for all internal hosts.
I'm trying to add some 2800 series routers to our monitoring environment, but I can't get them discovered.
On the Mgmt Server I need to go through a "discovery" process to add the 2800 to the system. For this I target the internal interface ( i) but the discovery fails. I'm assuming the packets are getting dropped on the outside interface (e). I know SNMP is set up correctly and works as I had PRTG installed on a local box (p) for testing purposes.
The intention is to do the data gathering via a proxy agent (p), so enableing SNMP on the outside interface is not going to do me any good.What do I need to do to let those discovery packets pass through? At least temporarily?
Any chance of one or preferably both of these before I flash the router to a more competent firmware?Rather ridiculous that there's no interface counters and no SNMP server. I prefer keeping stock firmware where possible but I need this functionality, it really isn't a big ask.That said I have an E4200 v1, which already looks like abandonware given it's been 6 months since the last firmware update - not amused and no intention of swapping a high performance router for one that sacrifices performance for better NAS functionality.
I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
