We have recently deployed several Ciso 887VAW (IOS 15.1(4)M4) to customer premises and I have come to realise counters show extremely high (not at all accurate) output rate and packets on all of them. [code]
View 2 RepliesI have an 837 ADSL router that the customer is upgrading from a 3 meg circuit to a 10 meg circuit.
The previous vendor used PPOE for connection and we used a dialer 1 interface to make the connection with a user name and password.
The new connection is a straight WAN DHCP no username or password needed.
I realize I can change the dialer interface from negotiate to DHCP but do I still need it ?
Can I replace the dialer 1 interface with IRB ? Should i just keep the Dialer 1 interface since the device is currently set that way and just remove the PPP negotiation from dialer 1 ?
I have applied a crypto map (fo ipsec vpn) on the dialer interface (for PPoE connection) in Cisco 2800; every time when the router restarts the crypto map is removed from the dialer interface even though i save the configuration every tim when i apply the map on the interface. Is there any way that the crypto map remains there on the dialer interface after the restart of router.
View 1 Replies View RelatedHow to make a Cisco 881 router finally work. I have the following configuration:
Current configuration : 2964 bytes
!
! No configuration change since last restart
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[code].....
As much as I understand, the VPN tunnel is active.I can access the Internet, but I cannot access anything through the VPN tunnel.
having some issues with a configuration using a Dialer interface. The interface comes up and the VPN tunnel comes up, but cannot access any network resources or the Internet.
The things that concern me most are my access lists as I have the static IP address that we are assigned via PPPOE - the IP never changes, but not sure if I can define it in the ACL or if I should be using an ANY tag.
Note: I've changed some IPs and username for security reasons.
!version 15.0service tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryptionservice sequence-numbers!hostname C2911-OTO01!boot-start-
[Code].....
I notice strange input rates on the interfaces of a 881 router:
show int fa4
..
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec
..
30 second input rate 85000 bits/sec, 11 packets/sec
30 second output rate 16000 bits/sec, 9 packets/sec
221434 packets input, 287889736 bytes
..
..
142286 packets output, 15683576 bytes, 0 underrun
How can 11 packets/sec be 85000 bits/sec -- average packet size of 8KB?. The total packets input (221434 packets versus 287+ MB) also shows this kind of a 10KB+ average packet size. There is ahardly any traffic through the router when the above snapshot was taken so 11 packets/sec sounds right, but not the 85Kbits/sec.
The router is running c880data-universalk9-mz.151-4.M4.bin and config is simple with a single Vlan (inside NAT) with a public IPs on fa4 and a couple of IPs for dynamic NAT. Everything works fine except for these interface counters that look worng.
I am configuring ISDN Interface on 2 Cisco 886VA Version 15.2(3)T . I am unable to set ppp multilink on the BRI0 interface and on the dialer interface. It's like the command doen't exist anymore.How can I fix that so that i can have 128 K bandwidth between ma 2 sites ?.
Router1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router1(config)#int bri0
Router1P(config-if)#ppp multilink
[code]....
I have two 3825's. Each has it's own ISP connection. Nat is configued for both. They have an ethernet connection between them and I'm running OSPF between the two so the routes propogate. I have qty 11 Dialer interfaces configured on each router (each router has an exact copy of the other routers dialer interface). However, I only want the Dialers up if the ISP connection on the mated router goes down. Much like HSRP I need one to preempt and be active if both ISP connections are up. When one goes down the other Dialers must come up. Each dialer sends a Dynamic DNS host name and IP address pair to DynDNS.org. So I cannot have both up otherwise the DNS names will bounce between ISP#1's IP address and ISP#2's IP address (back and forth). Let me know if any option exists to make this happen. As an aside the ISP's are providing me DHCP addresses so I cannot work off of an IP, it has to be the physical interface (i.e. Gi0/0).
View 1 Replies View RelatedI have the below configurations done on a 2900 router. [code]I would like to know, if the IP address assigned to dialer1 interface "20.1.2.133" would be listed in "show arp" ?, as it failed to list on our router and I want to know if this is an expected behavior ?
Secondly, does self ping 20.1.2.133 (dialer interface IP) work ? [code]
Is it possible to establish a interface dialer on a layar 3 switch?Or is it only interface for routers?I have a c3750 switch (WS-C3750G-24T), and when i try to establish a dialer interface i get an error message:
[code]...
i am having cisco 881 router i want to know whether i can configure dialer interface with username and password for my dsl internet connection.
View 2 Replies View RelatedI am attempting to monitor bandwidth utilization of the WAN port for the RV180 via SNMP and I am getting strange results. If a 256MB file is transferred from a remote server (without compression), the ifInOctets counter doesn't increment by anything resembling 256MB:
$ snmpget -v2c -c public 192.168.1.1 IF-MIB::ifInOctets.5 IF-MIB::ifOutOctets.5
IF-MIB::ifInOctets.5 = Counter32: 365402138
IF-MIB::ifOutOctets.5 = Counter32: 32610053
[Code].....
I'm reasonably certain that the .5 interface is the WAN port based on the value of ipAdEntIfIndex.X.X.X.X, but even if that were not the case, none of the other interfaces increment by a value close to the amount of data transfered. SNMP monitoring of a WAP121 on the same subnet returns expected results. I can only assume that SNMP on the RV180 is completely broken.
The router has the latest firmware available (1.0.1.9). There is only one network connection and the RV180 is the default gateway for all internal hosts.
vlan interface and physical interface (that is serving for this vlan ) have different input/output counters, there is only one physical interface in this vlan .
sh int vlan 64
30 second input rate 9000 bits/sec, 9 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
[Code]....
Any chance of one or preferably both of these before I flash the router to a more competent firmware?Rather ridiculous that there's no interface counters and no SNMP server. I prefer keeping stock firmware where possible but I need this functionality, it really isn't a big ask.That said I have an E4200 v1, which already looks like abandonware given it's been 6 months since the last firmware update - not amused and no intention of swapping a high performance router for one that sacrifices performance for better NAS functionality.
View 8 Replies View RelatedI have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..Is possible to get these values using SNMP?
View 3 Replies View RelatedI am having an issue with Cisco 1812j Router.
I have 2 1812j router. One router I accidentally lost the password so I reset the password as following link. [URL]
After that I could not submit "dialer" command. Like this.
c1812j-01(config)#int bri0c1812j-01(config-if)#d?dampening default delay descriptiondot1q dot1x down-when-looped dxi
c1812j-01(config-if)#
There is no choice to use "dialer" command.
The other Router is as below which looks ok.
c1812j-02(config)#int bri0c1812j-02(config-if)#d?dampening default delay descriptiondialer dialer-group dot1q dot1xdown-when-looped dxi
I guess I did something wrong to reset the unit.
I am trying to copy a setup from a Nortel IAX100 where the carrier provides two ATM PVC's over ADSL - one for voice (VoIP) and one for data (IP). Relevant lines from the backup of the IAX's configuration include the following for the PPP authentication over the voice circuit:
<wan_8_32>
<entry1 vccId="1" conId="1" name="Voice" protocol="PPPOE" encap="LLC" firewall="enable" nat="enable" igmp="disable" vlanId="-1" service="enable" instanceId="1509949441"/>
</wan_8_32>
<pppsrv_8_32>
<ppp_conId1 userName="" password="" serviceName="" idleTimeout="0" ipExt="disable" auth="auto" useStaticIpAddr="0" localIpAddr="255.255.255.255" />
</pppsrv_8_32>
The null username and password for the PPP connection have me a bit stumped. Does the PPP connection not use any authenetication at all? (Is that possible/likely? How could I deubg it?) Or does does the IAX100 supply a chap/pap response with null credentails? (If so, how would I duplicate that using an instruction to a dialer interface?I am configuring an 877 with 12.4T and advanced IP services.
To do this I’ve created another Dialer and re-assigned the atm interface (atm0/0/0) to it. Then I’ve done a shut and then a no shut a min or two later. To my surprise the debug ppp negotiation showed the user name from Dialer1 and then the line was back in my multi link bundle.
My relevant Config is below:
interface ATM0/0/0
no ip address
[Code]......
I have found this workable cisco 1841 config on the NET. From this link: [URL]
But it is doing source NAT from FA0/1 to Fa0/0. If we need to bridge, is it need to use “ip unnumbered”?
See my config below” 1841 config for Unifi, with ip unnumbered“, can work?
1841 config for Unifi, with NAT
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
! !
! Works perfectly on Cisco 1841, IOS v12.4(24)T !
[Code]....
We have a dsl connection on 897 dsl router at the customers HO.The telephone line is directly connected to router we configured dialer with username and password and it takes a static ip of 212.249.213.xxx.Now he has some branches that are connected through wireless links and he has arranged for a subnet of 8 public IP's in the range 72.70.245.xxx
Can we some how use these public ip's as secondary in the routers dialer interface and assign to the servers in the branches so that it can be accessed through web.
My customer recently deployed WLCs and WCS in their environment. However, recently they experienced slow performance. To futher finding out the root cause, I generated the 802.11 counters report from the WCS and noticed the following parameters is shown. Tx/Rx Fragment Count/Sec and FCS Error Count/Sec
1. Can I make the assumptions that the overall transfer of packet rate in that interval is the Total of Tx/Rx Fragment Count/Sec and FCS Error Count/Sec?
2. If the output rate of Tx/Rx Fragment Count/Sec and FCS Error Count/Sec are the same, does it mean that 50% of the packet are corrupted and this high FCA Error Count/Sec will cause performance degradation to the wireless througphput?
3. What is the baseline of the FCS Error Count/Sec that is acceptable? As for the case with wired, 1% error rate is acceptable. Will wireless have the same baseline?
We are a new call center company and want to configure the network to setup the predictive dialer, work properly.how a network could be setup to configure predictive dialer.
View 2 Replies View RelatedWe are trying to take ADSL interface into another VRF i.e (ip vrf forwarding VRF2 under dialer interface), the ip address negotiated command disappears, and although the dialer interface becomes up-up state, the adsl interface does not get an IP address dynamically.
Tried:
1) to reenter ip address negotiated again after changing the vrf of the interface, still the dialer interface shows "no ip address" under configuration
2) ppp ipcp accept-address again does not work.
the IOS version:c880data-universalk9-mz.151-2.T1.bin
Short of rebooting, is there a way to clear this counter on an ASA 5505?
sh int
Traffic Statistics for "inside":
39514338 packets input, 3103793436 bytes
13578097 packets output, 15566854561 bytes
[Code] ....
I have ACS 5.1, I have created a user with privilege 15. I need to allow a single command by command set. I have configured command set. in command set setting i have unchecked "Permit any command that is not in the table below"
and added command as below.
Grant Command Argument
Permit clear counters
its allowing me to run clear counters, good is its not allowing to show run and configuration t commands. And problem is i can run reload command also even show interface commands.I just want to allow clear counters command only.
I have a NETGEAR Wireless-N 150 Router WNR1000 v2. I am trying to configure it for my LAN which has a DIALER. [code] I tried to configure my NG but it is unable to connect to the network on its own. I have to use CONNECT dialer from my PC to connect which is useless because I can't use my wi-fi enabled devices to access network.
View 1 Replies View RelatedI am having ACS 5.2. I have to configure a user which would have privilege 7 access and addition to this, a user can run "clear counters" command.how to configure cammand set for "clear counters"?Can i run clear counters by privilege 7?
View 2 Replies View RelatedI have a cisco 870 router which I'm trying to connect to my ISP all the interfaces are in a up, up state. But I'm unable to ping any IP address on the internet. When I do a debug ppp I can see that the username and password are correct with the dialer 1 interface as there is no errors and I can see success. But when I shutdown the atm0 interface and then do a no shutdown I see a message called authentication failed.How does the atm0 interface work with the dialer,Also I spoke to the ISP and they can't see any connection being made but the debug shows success. I also get a default gateway via the ISP but it is the incorrect default gateway as I can't ping the internet and the ISP confirms that the default gateway is incorrect.
View 33 Replies View RelatedUsing an ACE 4710 we have a user setup with the Network-Monitor role which allows the user to view config, interface status, etc. We would also like to allow this user to clear the interface error counters as well, but nothing else.
View 2 Replies View RelatedI have a WLC 2106 with 3 APs. Everything works and users can connect, but the throughput seem to be lower than it should (it is around 8Mbps and should be around 30-50Mbps). And all speed and duplex has been accounted for.
I am trying to understand the stats that I see for the 802.11 MAC counters I under the Wireless APs.on the controller.
That screenshot is attached. I see high numbers for the following areas:
- Tx Failed Count
- RTS Failure Count
- FCS Error Count
what these mean and what could cause this? Maybe these are normal and not a concern.
we have a 878 router and we want to mark traffics when entering on its lan interface.its lan interface is a layer 2 interface and we have created vlan interface and assosiated lan interface to that vlan.on vlan interface itself there is no service-policy command so we have to put serive-policy command on interace fast 0 itself which is layer 2 port.when we assign service-policy to fast 0 it doesnt work and it does not mark any traffic also class default counters doesnt increase to indicate any traffic is passing even it is not getting marked. ios version is advipservices.124.9T. How to mark traffic on this port. ii dont know why service-policy command is supported on layer 2 interface when it doesnt work at all.
View 3 Replies View RelatedWe're running a simple policy map on a 3750 stack (IOS version 12.2(53)SE2), but the route-map counters do not show any matches:
NYKIRDRCX01#sh route-map
route-map remote-route, permit, sequence 51
Match clauses:
ip address (access-lists): remoteACL
Set clauses:
ip next-hop 192.168.101.5
Policy routing matches: 0 packets, 0 bytes
However, I've confirmed via our netflow monitor that the traffic we're trying to send to the appropriate next hop is, indeed, getting there correctly.
I've seen issues in the past with a 3750 not reporting counters correctly.
I have a big problem with my Cisco 1841 and the WIC-1AM-V2 in Slot 0.I got the task, to test if it is possible, to build up a connection (Dial on Demand Routing) to a remote modem, which is connected to a console port of another Cisco 1841, with the integrated modem card over POTS from the CLI of the router. My router will only dial out to the remote modems and only if its needed.I am connected to the router with the integrated modem card over a console cable on the console port. The remote modem is also connected to the console port of the remote Cisco 1841.
I found out, with my Dialer Profile configuration, it is possible to build up a connection. I configured a dialer list, that specifies that all ip traffic is permitted an interesting for my dialer interface. So a telnet or ping brings up my dialer, which brings up my Async interface. With the "show line" command, I can see that the TTY line, connected with the Async0/0/0 Interface is in use for 5 minutes, because of the "exec-timeout 5 0", which is configured on the remote router. Now the problem is, in this 5 minutes, I can not use a remote telnet on this line with my loopback interface, because the line is already in use and I get a "connection refused". The first telnet I use runs in a timeout, because the remote host is not responding. When I dial out directly from the modem card and not from the CLI with the AT-commands, I get also the connection and with a return i get the login prompt. I will post my actual config, so that you can see maybe a mistake I did or which command I must use, to get a working connection. [code]