Cisco WAN :: Assigning Secondary IP To Dialer Created On 897 Router
Sep 7, 2012
We have a dsl connection on 897 dsl router at the customers HO.The telephone line is directly connected to router we configured dialer with username and password and it takes a static ip of 212.249.213.xxx.Now he has some branches that are connected through wireless links and he has arranged for a subnet of 8 public IP's in the range 72.70.245.xxx
Can we some how use these public ip's as secondary in the routers dialer interface and assign to the servers in the branches so that it can be accessed through web.
View 1 Replies
ADVERTISEMENT
Dec 6, 2012
I have two 3825's. Each has it's own ISP connection. Nat is configued for both. They have an ethernet connection between them and I'm running OSPF between the two so the routes propogate. I have qty 11 Dialer interfaces configured on each router (each router has an exact copy of the other routers dialer interface). However, I only want the Dialers up if the ISP connection on the mated router goes down. Much like HSRP I need one to preempt and be active if both ISP connections are up. When one goes down the other Dialers must come up. Each dialer sends a Dynamic DNS host name and IP address pair to DynDNS.org. So I cannot have both up otherwise the DNS names will bounce between ISP#1's IP address and ISP#2's IP address (back and forth). Let me know if any option exists to make this happen. As an aside the ISP's are providing me DHCP addresses so I cannot work off of an IP, it has to be the physical interface (i.e. Gi0/0).
View 1 Replies
View Related
Sep 11, 2011
I have the below configurations done on a 2900 router. [code]I would like to know, if the IP address assigned to dialer1 interface "20.1.2.133" would be listed in "show arp" ?, as it failed to list on our router and I want to know if this is an expected behavior ?
Secondly, does self ping 20.1.2.133 (dialer interface IP) work ? [code]
View 2 Replies
View Related
Jul 11, 2011
I have a NETGEAR Wireless-N 150 Router WNR1000 v2. I am trying to configure it for my LAN which has a DIALER. [code] I tried to configure my NG but it is unable to connect to the network on its own. I have to use CONNECT dialer from my PC to connect which is useless because I can't use my wi-fi enabled devices to access network.
View 1 Replies
View Related
Mar 9, 2011
I want to configure my router to use 2 ADSL lines each with a dialer and a modem in RFC2684 mode. I have a 2821 (IOS 12.4) with an HWIC-4ESW.
My network topology is like this :
ADSL Modem 1 (RFC2684) --
(Fa0/0/0)
Router -- (Gi0/1) MyLAN
(Fa0/0/1)
ADSL Modem 2 (RFC2684) --/
1. I configure my DSL Modem in RFC 2684. The first use 172.16.0.2/29 and the second 172.16.0.3/29. I connect this devices to Fa0/0/0 and Fa0/0/1.
2. I configure Vlan1 to use the network configured on my modem :
interface Vlan1
ip address 172.16.0.1 255.255.255.248
3. I try to ping my devices :
#ping 172.16.0.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.3, timeout is 2 seconds:
!!!!!
[code]....
View 3 Replies
View Related
Mar 2, 2011
I have a 3725 routeur configured to receive the PPP/ATM/DSL connexion of our customer. I have found that the routeur has created 1035 virtual-access (1035 is his max) but I only have 85 customer on this router
View 1 Replies
View Related
Jan 22, 2012
I'm fairly new to Cisco configuration and I am looking at a problem for a client that involves the use of a Cisco 887 (wired only) as the main router/gateway. The problem I am investigating involves the allocatoni of DHCP addresses from the device to a product we have designed that connects to the router. I am attempting to set the 880 up on the bench with no ADSL connection and just use the DHCP feature of the box for the 4 switch ports on the back. I have tried all kinds of configurations from default. Whatever I do I can't get the router to assign an IP address to anything that is plugged in (Windows or Linux machines). What could I be doing wrong ? It can't be that difficult to get the system to just act as a DHCP server.
View 2 Replies
View Related
Dec 21, 2010
What are the possible effects of assigning an invalid address like 172.22.0.0 255.255.255.252 to a router interface. The 1841 router accepted the address?
View 12 Replies
View Related
Mar 6, 2011
i m using ISP provided modem+router and another D-Link Wireless router at the same time... My computer is connected to D-LInk's Router and D-Link's Router is connected to ISP's Modem...My modem's Ip address is : 192.168.1.1 Router's IP Address: 192.168.0.1ok but now problem is that now Dlink is connected to ISP's Modem and ISP's modem assigns different ip to Wl.Router. Both have DHCP enabled... But i want modem (which is also a router) to assign D-Link's router the STATIC IP... like 192.168.1.54Router Model is D-link DIR-615 Modem Model is ZTE EchoLife HG510a
View 1 Replies
View Related
Oct 25, 2012
hrome threw me a DNS lookup failed. I go into my network settings and I noticed that I had limited connectivity. It would switch between no network access and no internet access every few seconds. After a bit of fiddling around, I got it to connect through assigning myself a static IP. This isn't exactly convenient because I use this computer on multiple networks. When I try to have it on automatic IP, I get no IP address or default gateway when I do an ipconfig /all. It would appear that my router quit assigning my laptop an IP for no reason whatsoever. DHCP is enabled on the router, and all other devices work fine. What could possibly be the problem here? I'm 99% sure it's not an IP conflict either. It's not being MAC filtered because I'm on the thing right now posting this through a static IP. It's not my A/V because it's worked great in the past. Perhaps I should also mention it occasionally says "unidentified network" instead of the SSID
View 8 Replies
View Related
Jul 2, 2011
The WRT110 is hooked up to Cable through Comcast and works fine with LAN connections. The problem comes in with more than one wireless laptop tries to connect. First, it was loaded with 1.0.4 firmware and my girlfriend's XP laptop would connect but drop the connection a lot. My Windows 7 laptop wouldn't connect at all. After trying everything someone recommended upgrading the firmware to 1.0.7. Well, now my Windows 7 laptop connects but the XP laptop will not. The DHCP won't assign it an IP, although it says it's connected.
View 2 Replies
View Related
Feb 13, 2012
problem I have encountered with a Cisco E4200v2 router (with current firmware update) which is just over three months old. The other day my internet connection (cable "always on") hiccuped a couple of time (which is not unusual for this area). However, when the service finally restored itself, I lost a PC and printer from my home network, and the ability to connect to the internet with the wired PC. Outages like this are normal in this area and have not had an issue like this before. Both were "wired" via (CAT 5e) cables. The three PC's that were connected via wi-fi were not affected. We switched CAT 5e cables several times with not changed in status. The wired printer and PC were assigned arbitrary ip addresses in the 16X.XXX etc. range. I think that has to do with not being able to communicate with the DHCP server? However, we connected one of the laptops via a CAT 5e cable directly to the router, and it too was assigned an arbitrary ip address. I finally reverted to my old router (LINKSYS WRT160N), and the issue went away. Is this a known E4200v2 issue? Is there a fix or workaround for this? The "wired" PC and two laptops are Windows 7, and the all-in-one is running Vista.I can continue using my WRT16N. But hate to think I wasted good money on this new dual band. Have never had any issues before with Linksy/Cisco before.
View 8 Replies
View Related
May 20, 2012
The problem is WAP 610n not assigning IP address through DHCP; i have to add IP address mannualy.
just go through the details below:
In my network environment we are using :
CISCO Router 800 series; IP: 192.168.1.1
Domain server with DHCP server : 192.168.1.2
DHCP pool: 192.168.1.234 - 192.168.1.250
WAP IP : 192.168.1.236
WAP configuration :
configuration view : mannual
Wireless band : 2.4 Ghz
Network mode : mixed
channel width: 20 Mhz only
standard channel : auto
SSID broadcast : Disabled [ for security reason]
Security mode : WPA2 Personal
Encryption : TKIP/AES
Firmware : 1.0.01 build 94, Oct 26, 2009
Note: In status menu it is not showing any default gateway.
Encapsulation method in CISCO router : PPPoA [ as instructed by ISP]
View 5 Replies
View Related
Jan 22, 2012
I have a nas device called mybooklive connected to my linksys e2500 router.Every device that is connected to the router does not append nyc.rr.com except the mybooklive one.I change and mad dhcp reservation for this device with the client name but it still appends. [code]
View 1 Replies
View Related
Feb 10, 2013
We have recently deployed several Ciso 887VAW (IOS 15.1(4)M4) to customer premises and I have come to realise counters show extremely high (not at all accurate) output rate and packets on all of them. [code]
View 2 Replies
View Related
Jun 21, 2011
I have an 837 ADSL router that the customer is upgrading from a 3 meg circuit to a 10 meg circuit.
The previous vendor used PPOE for connection and we used a dialer 1 interface to make the connection with a user name and password.
The new connection is a straight WAN DHCP no username or password needed.
I realize I can change the dialer interface from negotiate to DHCP but do I still need it ?
Can I replace the dialer 1 interface with IRB ? Should i just keep the Dialer 1 interface since the device is currently set that way and just remove the PPP negotiation from dialer 1 ?
View 1 Replies
View Related
Apr 25, 2011
I have been having problems when trying to host servers on games, etc.I have 2 routers. A modem router, which is a Thomson router. That is the main one. It has a wire connecting from it, to a D-Link router that is near my Computer, and my brother's one. Then that D-Link router has 2 wires from each port, to mine, and my brother's computer.So, I am trying to host games.I didn't connect to the Thomson one, which is also wireless. I am connected to the wired one (D-Link). When I try to host while connected to it, my brother, and other people can't find the server. My brother and me can find it on LAN, but not Internet.But when I disconnect from the Wired, and connect to the Thomson wireless one, and then when I host, I can find it on INTERNET. Even my brother can. He can connect to it perfectly.
I do not want to connect to the wireless, because then it will cause lag spikes every 5 minutes.So, when I disconnect from the wireless, and connect to the wire, I went into the CMD, and typed in ipconfig. I found out that the Default Gteway is the D-Link IP.When I connect to the wireless, and disconnect the wired, I went into CMD, and then the Default Gateway is the Thomson one, which is the main router.So what I want to do, is use the D-Link router, and that router will have the same IP as my thomson one, so that I can host perfectly with no lag spikes, and using a wired connection.
View 19 Replies
View Related
Jul 4, 2011
I have applied a crypto map (fo ipsec vpn) on the dialer interface (for PPoE connection) in Cisco 2800; every time when the router restarts the crypto map is removed from the dialer interface even though i save the configuration every tim when i apply the map on the interface. Is there any way that the crypto map remains there on the dialer interface after the restart of router.
View 1 Replies
View Related
Jan 6, 2011
I am having an issue with Cisco 1812j Router.
I have 2 1812j router. One router I accidentally lost the password so I reset the password as following link. [URL]
After that I could not submit "dialer" command. Like this.
c1812j-01(config)#int bri0c1812j-01(config-if)#d?dampening default delay descriptiondot1q dot1x down-when-looped dxi
c1812j-01(config-if)#
There is no choice to use "dialer" command.
The other Router is as below which looks ok.
c1812j-02(config)#int bri0c1812j-02(config-if)#d?dampening default delay descriptiondialer dialer-group dot1q dot1xdown-when-looped dxi
I guess I did something wrong to reset the unit.
View 8 Replies
View Related
May 11, 2013
How to make a Cisco 881 router finally work. I have the following configuration:
Current configuration : 2964 bytes
!
! No configuration change since last restart
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[code].....
As much as I understand, the VPN tunnel is active.I can access the Internet, but I cannot access anything through the VPN tunnel.
View 3 Replies
View Related
Jan 9, 2011
having some issues with a configuration using a Dialer interface. The interface comes up and the VPN tunnel comes up, but cannot access any network resources or the Internet.
The things that concern me most are my access lists as I have the static IP address that we are assigned via PPPOE - the IP never changes, but not sure if I can define it in the ACL or if I should be using an ANY tag.
Note: I've changed some IPs and username for security reasons.
!version 15.0service tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryptionservice sequence-numbers!hostname C2911-OTO01!boot-start-
[Code].....
View 1 Replies
View Related
Aug 1, 2011
I currently have my wired cable internet hooked into my wrt310n. I have that hooked into a linksys 10/100 ef3124 switch. From there, I have cat5 run to the back of my house, where the wireless signal is weakest. I've got an E2000 router and would like to hook that in at the back of the house. What settings do I need to make in order to set up a completely new wireless network in the back of the house?
View 1 Replies
View Related
May 22, 2013
I have an MPLS network router(Router1) and an internet router(Internet1) at a site of mine(Site1). the MPLS router sends all unknown traffic out the internet router. Router1 is the default gateway for all hosts and directs the traffic.I also have another network at an alternate site (Site2) on the same mpls network also with an internet egress. It is composed of an MPLS router (router2) and an internet router (Internet2).I would like Router1 to send internet bound traffic out Internet2 if Internet1 is down. Basically the statement on Router1 for the unknown traffice is ip route 0.0.0.0 0.0.0.0 172.31.1.254I have never heard of IP SLA before but it seems to be the best method for this situation.
View 2 Replies
View Related
Jan 30, 2013
I have two routers on my local network:
1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled)
2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2
There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the same subnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it possible by configuring the DHCP server to assign the primary DNS address as 192.168.1.1 and secondary DNS address as 192.168.1.2?
View 11 Replies
View Related
Jul 14, 2011
I was setting a static IPs for my PCs, and for the Preferred and Alternate DNS Server addresses I looked on my router's Device Information page. It had "Primary DNS Server: 121.98.0.1", but "Secondary DNS Server:" is reported as "0.0.0.0". Router is a DIR-655:
I looked on my ISP's website and they have "121.98.0.2" listed as the Secondary Name Server/DNS:
Why does the router not report that? Is there something wrong? Should I still set 121.98.0.2 as the Alternate DNS Server in Windows?
EDIT: BTW, my modem reports both primary and secondary DNS servers on it's info page.
View 6 Replies
View Related
Sep 7, 2011
I am trying to copy a setup from a Nortel IAX100 where the carrier provides two ATM PVC's over ADSL - one for voice (VoIP) and one for data (IP). Relevant lines from the backup of the IAX's configuration include the following for the PPP authentication over the voice circuit:
<wan_8_32>
<entry1 vccId="1" conId="1" name="Voice" protocol="PPPOE" encap="LLC" firewall="enable" nat="enable" igmp="disable" vlanId="-1" service="enable" instanceId="1509949441"/>
</wan_8_32>
<pppsrv_8_32>
<ppp_conId1 userName="" password="" serviceName="" idleTimeout="0" ipExt="disable" auth="auto" useStaticIpAddr="0" localIpAddr="255.255.255.255" />
</pppsrv_8_32>
The null username and password for the PPP connection have me a bit stumped. Does the PPP connection not use any authenetication at all? (Is that possible/likely? How could I deubg it?) Or does does the IAX100 supply a chap/pap response with null credentails? (If so, how would I duplicate that using an instruction to a dialer interface?I am configuring an 877 with 12.4T and advanced IP services.
View 11 Replies
View Related
Aug 28, 2012
To do this I’ve created another Dialer and re-assigned the atm interface (atm0/0/0) to it. Then I’ve done a shut and then a no shut a min or two later. To my surprise the debug ppp negotiation showed the user name from Dialer1 and then the line was back in my multi link bundle.
My relevant Config is below:
interface ATM0/0/0
no ip address
[Code]......
View 1 Replies
View Related
Aug 17, 2011
I have found this workable cisco 1841 config on the NET. From this link: [URL]
But it is doing source NAT from FA0/1 to Fa0/0. If we need to bridge, is it need to use “ip unnumbered”?
See my config below” 1841 config for Unifi, with ip unnumbered“, can work?
1841 config for Unifi, with NAT
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
! !
! Works perfectly on Cisco 1841, IOS v12.4(24)T !
[Code]....
View 1 Replies
View Related
Nov 29, 2012
We are a new call center company and want to configure the network to setup the predictive dialer, work properly.how a network could be setup to configure predictive dialer.
View 2 Replies
View Related
Feb 22, 2013
I have more than 5000 sq. ft home and have some dead places other end of the house. Now I am looking for Range Extender/Repeater to boost signal. My primary wireless router is Motorola Surfboard SBG6580 and Secondary Linksys E3000 (planning to update firmware to DD-WRT). So I wanted something such that I can roam between the two routers without switching SSID (use single SSID name for primary and secondary DD-WRT routers) and connect automatically to whichever the best signal (or) strength router. In work place we have same thing like that single wireless SSID name which automatically connect wireless SSID from one end to another end of the building.
View 1 Replies
View Related
Oct 15, 2012
I am configuring ISDN Interface on 2 Cisco 886VA Version 15.2(3)T . I am unable to set ppp multilink on the BRI0 interface and on the dialer interface. It's like the command doen't exist anymore.How can I fix that so that i can have 128 K bandwidth between ma 2 sites ?.
Router1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router1(config)#int bri0
Router1P(config-if)#ppp multilink
[code]....
View 2 Replies
View Related
Feb 27, 2011
We are trying to take ADSL interface into another VRF i.e (ip vrf forwarding VRF2 under dialer interface), the ip address negotiated command disappears, and although the dialer interface becomes up-up state, the adsl interface does not get an IP address dynamically.
Tried:
1) to reenter ip address negotiated again after changing the vrf of the interface, still the dialer interface shows "no ip address" under configuration
2) ppp ipcp accept-address again does not work.
the IOS version:c880data-universalk9-mz.151-2.T1.bin
View 1 Replies
View Related
May 7, 2012
Is it possible to establish a interface dialer on a layar 3 switch?Or is it only interface for routers?I have a c3750 switch (WS-C3750G-24T), and when i try to establish a dialer interface i get an error message:
[code]...
View 2 Replies
View Related
