Cisco Switching/Routing :: 880 (887) - Router Not Assigning IP Address
Jan 22, 2012
I'm fairly new to Cisco configuration and I am looking at a problem for a client that involves the use of a Cisco 887 (wired only) as the main router/gateway. The problem I am investigating involves the allocatoni of DHCP addresses from the device to a product we have designed that connects to the router. I am attempting to set the 880 up on the bench with no ADSL connection and just use the DHCP feature of the box for the 4 switch ports on the back. I have tried all kinds of configurations from default. Whatever I do I can't get the router to assign an IP address to anything that is plugged in (Windows or Linux machines). What could I be doing wrong ? It can't be that difficult to get the system to just act as a DHCP server.
View 2 Replies
ADVERTISEMENT
Apr 9, 2012
Recently purchased 5 SGE2010P 48-port switches to replace older L2 switches. I have 4 switches in single stack and one as a standalone. Both the stack and standalone will connect to at least 1 Dell 2724 switch. Both the stack and the standalone Cisco are in Layer 3 mode.
I have created several VLans on the Cisco switches, and am trying to assign an IP address to the VLan, but cannot seem to figure out the web gui. Each time I try to use Systems > System Management > IP Addressing > IP Interface, then click Add, it simply changes the existing IP of the management interface. So, I'm not sure how to go about assigning an IP Address to an Vlan.
View 15 Replies
View Related
Nov 20, 2011
The DHCP/DNS server is on ip address 10.1.100.103 with an alt on .102 I'm attempting to integrate a 4510R+E into an existing network and use existing DHCP/DNS windows 2008 server to push out IP addresses to connected computers.
I want to assign a VLAN to every port for management purposes and then I put an IP helper address on every VLAN.
I've attached a the 4500E partial config. I'm attempting to get Gi1/44 to a state where I can plug a computer into it an resolve an ip address and gain internet access like all the devices on the existing network can do.
I've created a new scope in DHCP with the ip subnet of 10.60.211.0 255.255.255.0 It leases addresses from .1 to .253
The computer will not resolve ip addresses with this config.
View 5 Replies
View Related
Oct 25, 2012
hrome threw me a DNS lookup failed. I go into my network settings and I noticed that I had limited connectivity. It would switch between no network access and no internet access every few seconds. After a bit of fiddling around, I got it to connect through assigning myself a static IP. This isn't exactly convenient because I use this computer on multiple networks. When I try to have it on automatic IP, I get no IP address or default gateway when I do an ipconfig /all. It would appear that my router quit assigning my laptop an IP for no reason whatsoever. DHCP is enabled on the router, and all other devices work fine. What could possibly be the problem here? I'm 99% sure it's not an IP conflict either. It's not being MAC filtered because I'm on the thing right now posting this through a static IP. It's not my A/V because it's worked great in the past. Perhaps I should also mention it occasionally says "unidentified network" instead of the SSID
View 8 Replies
View Related
May 20, 2012
The problem is WAP 610n not assigning IP address through DHCP; i have to add IP address mannualy.
just go through the details below:
In my network environment we are using :
CISCO Router 800 series; IP: 192.168.1.1
Domain server with DHCP server : 192.168.1.2
DHCP pool: 192.168.1.234 - 192.168.1.250
WAP IP : 192.168.1.236
WAP configuration :
configuration view : mannual
Wireless band : 2.4 Ghz
Network mode : mixed
channel width: 20 Mhz only
standard channel : auto
SSID broadcast : Disabled [ for security reason]
Security mode : WPA2 Personal
Encryption : TKIP/AES
Firmware : 1.0.01 build 94, Oct 26, 2009
Note: In status menu it is not showing any default gateway.
Encapsulation method in CISCO router : PPPoA [ as instructed by ISP]
View 5 Replies
View Related
May 26, 2012
I am trying to give an static ip address to a time clock on my network and for some reason when I connect time clock to network it will always get an ip address from a different network. for example my computer IP address is 192.168.2.70 when connected to network, my default gateway is 192.168.2.1, the IP address that the time clock always gets is 192.168.1.120, there is no way to tell the time clock what IP address I wanted to be it has to get it from router (that is what the manufacturer told me), router (16portLiksys) does not have DHCP enabled the guy who set up network left it disabled, on his notes he says server (dell server T110) is acting as router is that true that a server can be acting as router?what do guys think is going on here?all the computers hooked up to network have static IP address.I also notice that when I connect a computer to router it will get an IP address from different network the same as time clock.I tried to reserve ip address on router by entering MAC address from time clock but it won't work. I am not very familiar with the server settings I have not try changing settings on server, I am not even sure the guy who set up network is right about using server as router.
View 1 Replies
View Related
Jul 25, 2012
My company wants to create a VPN Tunnel to allow a remote office to connect to ours. I purchased 2 ASA 5505 and I was expecting to be able to set this up without any issues. Sadly, that is not the case.
What I'm having trouble with is configuring my Public IP Address to the device. I go through the setup wizard and enter the IP Address like normal, but I have no option to input my ISP's subnet, Gateway or DNS. Without those, I get no internet connection. I know there is a way to do this, but I'm stumped.
My Specs:
2 ASA 5505 series
ISP Modem (Which they control) - SMC SMCD3GN with DHCP disabled
View 1 Replies
View Related
Jan 7, 2013
HP wifi printers (I've had 2 over the last several years)eventually have a disconnect with my wifi router and was told (by an experienced IT guy from my last job) I should assign the printer a static address to eliminate the problem. How can I assign a static address to my printer. Here are the models Router: Belkin model F5D9231-4v1(01); Printer HP Officejet 6600. I know how to access the printer and manually enter an IP address and subnet and such, I just don't know which numbers to use where. I also know how to access my router, via typing in the IP address in Internet Explorer, but i'm unsure of which tab within the router's page (i.e. is it category wirelessunder MAC address control) or which numbers (IP address or MAC Address)and where should I get the correct numbers from (i.e. go run, cmd,IPconfig/all).
View 6 Replies
View Related
Jul 1, 2012
I am using Windows 2011 SBS and Windows 7 clients.My server has a DHCP range of 192.x.x.150 to 192.x.x.199 and all other I.P. addresses are static. On a workstation located at I.P. 192.x.x.13 I am seeing an address conflict.When I perform an "nbtstat -a 192.x.x.13" command from the server I am given the logical computer name of a staff members personal laptop.Investigation of the laptop reveals that it is set to DHCP, and clearly the address of 192.x.x.13 is outside of my servers DHCP scope, so this I.P.should never be assigned, let alone in duplicate.I Google this topic before posting, and it was suggested that IPv6 could be having an adverse affect. I determined this because I performed a ping on the laptop and only got a MAC address back rather than an I.P. address.However after unticking IPv6, and rebooting, the laptop is still causing havoc.I can set a static I.P. address on the laptop, however this is not ideal.
View 2 Replies
View Related
Oct 12, 2011
We once had a virtual server with two network adapters, one was internal and the other was external, and people could access it directly from the internet.
That server recently, died (someone put the .VHD file on a massive RAID 0 array, and that went boom), and I need to set it back up again. All the DNS entries appear to still be there, but how to assign the external IP to the network adapter. I tried Google, but my Google-fu must be weak today as I can't find anything useful.
It's a Server 2008 R2 machine running inside Hyper-V. Nothing's changed except for the new Windows install, it's running with the exact same VM settings, which I didn't touch except to add a new VHD.
View 5 Replies
View Related
Jun 25, 2011
I just got a brand new laptop and I can't get it to connect to LAN.It's plugged in to the same hub as my main machine and I can't even access my router UI.It's not the cable because I tried plugging in my main machine's cable to the new laptop and the same thing happens.ipconfig reveals an Autoconfiguration IPv4 Address of: 169.254.197.187 But that number should say 192.168.1.1xx I've tried uninstalling and reinstalling the Ethernet driver as well.I've tried resetting the router and modem.I've tried resetting TCP/IP.
View 13 Replies
View Related
Feb 16, 2013
some problems when I was trying to install my X3000 as a DSL modem and router.I had to assign a designated IP address but I have dynamic IP from my internet supplier. I can't get pass the stepp of assigning IP address.
View 4 Replies
View Related
Apr 3, 2011
Is there anyway you can assign a static IP address within WAG160Nv2 to peripherals such as an XBOX?
The knowledge base only seems to show how to assign an IP address in the XBOX but when I have to reboot the router, I've noticed the XBOX is assigned a new IP address when viewed in the router pages.
If I set a permanent IP address in the XBOX, this will no longer match what is in the router.
View 1 Replies
View Related
Jan 29, 2013
We have a Cisco 2911 router in our company. I didn't set it up myself nor I was involved. I only started working here recently, bit over 3 months ago. I have been given ongoing task which other IT Technicians been struggling for almost a year with a idea that maybe because I'm fresh person in the company I will find a original idea why could this thing not work.
Our router have a problem with blocking a single IP address, but not completely It's hard to explain but I will try my best. Company is hosting their website externally and accessing the host and FTP on the host on daily bases. It is important for the website to work on the internal network in company. It does work sometimes, but from time-to-time the website showing time-out error 118 on any point before Cisco router using both http and https, have tried putting just the IP address( doesn't matter is it on the general network or last ISA server on DMZ ). I am able to connect to the website using any of proxy gates but not directly to the website. I have also tested the connection past the router and I was able to connect to the website without any problems. I am also able to ping the host's address from the router and internal network.
I have eliminated the possibility of not correctly setup proxy or firewall on the network as problem also occur on the DMZ. I have also checked access-lists on the router and firewall rules for Any possibilities and I can't really see a way why would the router do this.
View 2 Replies
View Related
Dec 2, 2011
How i can transfer the router logs to email address.Wev are using the router 2600.
View 5 Replies
View Related
Jan 7, 2013
We have a cisco 2911 router configured with password for telnet login, but I always failed to login use telnet, does any one know any place need to be modify?
View 6 Replies
View Related
Jan 30, 2011
I have a 3911 router with a 1242 AP. The problem that I have is that when the user is trying to connect, the user get the OS Ip address 169.254.168.154 and I see that when I do the "show dot11 association" command, but when I do sh ip dhcp binding on the router I see
172.19.9.141 0100.18de.74db.14 Jan 31 2011 11:14 AM Automatic
The router is seeing as if the router gave the ip address to the user, but the reality the user was assigne the OS ip address 169. I did "debug ip dhcp server events" and I got the following:
Jan 31 11:09:06.752 EST: DHCPD: Seeing if there is an internally specified pool class:Jan 31 11:09:06.756 EST: DHCPD: htype 1 chaddr 0100.18de.74db.14
Jan 31 11:09:06.756 EST: DHCPD: remote id 020a00000a58218400000000Jan 31
[Code].....
View 10 Replies
View Related
Jul 15, 2012
I have just updated a VLAN interface on my router. I have two 6500's with GLBP configured. The particular interface had a primary and secondary IP address. I shutdown the interface on one router and deleted the secondary address then assigned the orignal secondary address to be the be the only address associated with the interface and enabled the interface and it came right back up...all looks good. I proceeded to do the same thing to the other router and once again all looked good. Now, I am able to PING the devices in the subnet from router, but am unable to ping them from any place else. [code]
View 2 Replies
View Related
Sep 7, 2012
We have a dsl connection on 897 dsl router at the customers HO.The telephone line is directly connected to router we configured dialer with username and password and it takes a static ip of 212.249.213.xxx.Now he has some branches that are connected through wireless links and he has arranged for a subnet of 8 public IP's in the range 72.70.245.xxx
Can we some how use these public ip's as secondary in the routers dialer interface and assign to the servers in the branches so that it can be accessed through web.
View 1 Replies
View Related
Dec 28, 2011
This is my first time trying to configure a WAP for out network. I have an AP1141 connecting to an SG300-28 switch. The subnet for my WAPs is 10.10. 40.0/ 24. The rest of my internal network is 10.10.10.0/24. There are four other WAPs on the 10.10.40.0/24 network that I did not configure. When I assign an IP address - 10.10.40.7 to my WAP with the gateway as 10.10.40.100 (router), I cannot ping anything. If I assign the WAP an IP address - 10.10.10.192 with the gateway 10.10.10.100 (router), I can ping everything.
View 6 Replies
View Related
Dec 21, 2010
What are the possible effects of assigning an invalid address like 172.22.0.0 255.255.255.252 to a router interface. The 1841 router accepted the address?
View 12 Replies
View Related
Mar 6, 2011
i m using ISP provided modem+router and another D-Link Wireless router at the same time... My computer is connected to D-LInk's Router and D-Link's Router is connected to ISP's Modem...My modem's Ip address is : 192.168.1.1 Router's IP Address: 192.168.0.1ok but now problem is that now Dlink is connected to ISP's Modem and ISP's modem assigns different ip to Wl.Router. Both have DHCP enabled... But i want modem (which is also a router) to assign D-Link's router the STATIC IP... like 192.168.1.54Router Model is D-link DIR-615 Modem Model is ZTE EchoLife HG510a
View 1 Replies
View Related
Jul 2, 2011
The WRT110 is hooked up to Cable through Comcast and works fine with LAN connections. The problem comes in with more than one wireless laptop tries to connect. First, it was loaded with 1.0.4 firmware and my girlfriend's XP laptop would connect but drop the connection a lot. My Windows 7 laptop wouldn't connect at all. After trying everything someone recommended upgrading the firmware to 1.0.7. Well, now my Windows 7 laptop connects but the XP laptop will not. The DHCP won't assign it an IP, although it says it's connected.
View 2 Replies
View Related
Feb 13, 2012
problem I have encountered with a Cisco E4200v2 router (with current firmware update) which is just over three months old. The other day my internet connection (cable "always on") hiccuped a couple of time (which is not unusual for this area). However, when the service finally restored itself, I lost a PC and printer from my home network, and the ability to connect to the internet with the wired PC. Outages like this are normal in this area and have not had an issue like this before. Both were "wired" via (CAT 5e) cables. The three PC's that were connected via wi-fi were not affected. We switched CAT 5e cables several times with not changed in status. The wired printer and PC were assigned arbitrary ip addresses in the 16X.XXX etc. range. I think that has to do with not being able to communicate with the DHCP server? However, we connected one of the laptops via a CAT 5e cable directly to the router, and it too was assigned an arbitrary ip address. I finally reverted to my old router (LINKSYS WRT160N), and the issue went away. Is this a known E4200v2 issue? Is there a fix or workaround for this? The "wired" PC and two laptops are Windows 7, and the all-in-one is running Vista.I can continue using my WRT16N. But hate to think I wasted good money on this new dual band. Have never had any issues before with Linksy/Cisco before.
View 8 Replies
View Related
Jan 22, 2012
I have a nas device called mybooklive connected to my linksys e2500 router.Every device that is connected to the router does not append nyc.rr.com except the mybooklive one.I change and mad dhcp reservation for this device with the client name but it still appends. [code]
View 1 Replies
View Related
Aug 10, 2011
I disconnected and reconnected the powercable while holding on to the setup button until system, alert, setup go amber. The system led light began blinking green. I waited until one of the leds lights on the ports starts blinking green I then connected the ethernet cable connected to my pc. I made sure my lan connection on my computer was set to dhcp.In the docs claim it should take about 1 minute to grab a new ip address. After a few minutes i check the ipconfig on my pc and I get the apipa address.The setup light on the switch remains green while system is amber. The led for port 1 stopped blinking and remains green.My pc is not grabbing an ip address I don't know what else to do.
View 7 Replies
View Related
Nov 18, 2012
We have a Router with one External IP and a couple of VLANs. We have got a Teleconferencing Unit that needs almost every port known to man to work, so decided to get the unit its own External IP.
We have the IP now and how to get it in the router and then also to use it only for the Video unit (From outside straight through to Video).
Im comfortable adding lines to the router but just don't know what the lines should be.
The new IP's purchased are 116.199.222.200/30 (Only need to use one address, lets say 116.199.222.200). No idea what the subnet mask should be...
The router config below stripped of irrelevant stuff:
interface FastEthernet0
no ip address
!
interface FastEthernet1
[Code]......
View 11 Replies
View Related
Jan 22, 2013
I would like to know why Cat3550 SVI's mac address is always same.for example if I configure interface vlan1 and vlan2.mac address is same as like 000d.bdfc.xxxx but Cat3750 is different, each SVI has unique mac address.
View 1 Replies
View Related
Aug 26, 2007
how to configure an IPaddress for a PWR-RPS 2300?.I tried finding info on the website but no luck as yet. RPS 2300 will be used on stack of 3750E series switches.
View 3 Replies
View Related
Apr 27, 2012
I have a POE switch running 12.0(5). I have port 24 connected as a trunk connected to the main switch. I need to add an ip address on vlan 21 which is where the network vlan is. I created it but I can not seem to enable it. I have issued the no shut command several times, but doing "sh ip int brief" it keeps showing up as administively down.
View 13 Replies
View Related
Feb 20, 2013
I would like to enable port security to hardcode the MAC address on the ethernet switch. There are 5 ethernet ports in the same ethernet switch to be assigned for one person (one note book), e.g. port 5, 6, 15, 16 and 23. The model of ethernet switch is cisco 2960S and one MAC address is configured on 2960S.
1. Does 2960S support this requirement to allow input the same MAC address to 5 different port?
2. If yes, can ethernet switch "smart" enough to forward the packages to "active" ethernet port which is connected to notebook and the rest of four ports are inactive.
3. if no, any solution or any work around to achieve this requirement
View 5 Replies
View Related
Oct 31, 2012
The customer has 4 6500 switches. 2 Physical locations, and 2 switches at each locations. The locations are connected via 1 200mpbs metro ethernet(layer 2). We ran into an issue during a DR exercise. We had created a VLAN for DR testing purposes, that did not have any SVI configured, but the VLAN did exist on one of the 6500s. When the customer restored a VM to the DR VLAN, we lost connectivity to the production server. After some troubleshooting, we found the cause to be the same mac address showing up, but in a different vlan. Once we removed the DR vlan from the 6500 all was well. It seems like switches are ignoring the VLAN in the mac address table, and forwarding to the incorrect ports. The switch is not reporting any mac flapping in the logs. No spanning tree topology changes are occurring. Code version is 12.2(33)SXJ2 on all switches.
View 1 Replies
View Related
Jan 1, 2013
I have a new 881 router and am simply trying to change the ip address from the default 10.10.10.1 to 192.168.15.1
I tried doing this both in the CCP Express app loaded on the router, and also using the desktop CCP client. I can change other parameters without any problems, but when I change the ip address of the vlan the program hangs (as expected since the ip address should be changing). I then try to open it back up and reconnect but get no response from the router.
I can ping it no problem, and the http server is running according to the serial terminal.
View 1 Replies
View Related
