Assigning A Static Address To A Printer?
Jan 7, 2013
HP wifi printers (I've had 2 over the last several years)eventually have a disconnect with my wifi router and was told (by an experienced IT guy from my last job) I should assign the printer a static address to eliminate the problem. How can I assign a static address to my printer. Here are the models Router: Belkin model F5D9231-4v1(01); Printer HP Officejet 6600. I know how to access the printer and manually enter an IP address and subnet and such, I just don't know which numbers to use where. I also know how to access my router, via typing in the IP address in Internet Explorer, but i'm unsure of which tab within the router's page (i.e. is it category wirelessunder MAC address control) or which numbers (IP address or MAC Address)and where should I get the correct numbers from (i.e. go run, cmd,IPconfig/all).
View 6 Replies
ADVERTISEMENT
May 26, 2012
I am trying to give an static ip address to a time clock on my network and for some reason when I connect time clock to network it will always get an ip address from a different network. for example my computer IP address is 192.168.2.70 when connected to network, my default gateway is 192.168.2.1, the IP address that the time clock always gets is 192.168.1.120, there is no way to tell the time clock what IP address I wanted to be it has to get it from router (that is what the manufacturer told me), router (16portLiksys) does not have DHCP enabled the guy who set up network left it disabled, on his notes he says server (dell server T110) is acting as router is that true that a server can be acting as router?what do guys think is going on here?all the computers hooked up to network have static IP address.I also notice that when I connect a computer to router it will get an IP address from different network the same as time clock.I tried to reserve ip address on router by entering MAC address from time clock but it won't work. I am not very familiar with the server settings I have not try changing settings on server, I am not even sure the guy who set up network is right about using server as router.
View 1 Replies
View Related
Apr 3, 2011
Is there anyway you can assign a static IP address within WAG160Nv2 to peripherals such as an XBOX?
The knowledge base only seems to show how to assign an IP address in the XBOX but when I have to reboot the router, I've noticed the XBOX is assigned a new IP address when viewed in the router pages.
If I set a permanent IP address in the XBOX, this will no longer match what is in the router.
View 1 Replies
View Related
Nov 10, 2011
My printer (HP7210) is wired connected to my WRT54GL router. 2 computers have also a wired connection, my laptop is connected wireless. All these computers use the connected printer. 2 computers can only use a static IP-address for the printer. How can I set a static IP address in my router?
View 3 Replies
View Related
May 20, 2011
I posted of an issue we were having but I feel like I was getting ahead of myselfBasically I need to know how to do 2 things.I want to assign a static IP I purchased from Comcast to my Netgear N300 router and then in turn want that IP address to be linked to the server here in our office so that when people use the Remote Desktop Connection it directs them to the proper machine.
View 5 Replies
View Related
Mar 6, 2011
i m using ISP provided modem+router and another D-Link Wireless router at the same time... My computer is connected to D-LInk's Router and D-Link's Router is connected to ISP's Modem...My modem's Ip address is : 192.168.1.1 Router's IP Address: 192.168.0.1ok but now problem is that now Dlink is connected to ISP's Modem and ISP's modem assigns different ip to Wl.Router. Both have DHCP enabled... But i want modem (which is also a router) to assign D-Link's router the STATIC IP... like 192.168.1.54Router Model is D-link DIR-615 Modem Model is ZTE EchoLife HG510a
View 1 Replies
View Related
Jul 1, 2012
I am using Windows 2011 SBS and Windows 7 clients.My server has a DHCP range of 192.x.x.150 to 192.x.x.199 and all other I.P. addresses are static. On a workstation located at I.P. 192.x.x.13 I am seeing an address conflict.When I perform an "nbtstat -a 192.x.x.13" command from the server I am given the logical computer name of a staff members personal laptop.Investigation of the laptop reveals that it is set to DHCP, and clearly the address of 192.x.x.13 is outside of my servers DHCP scope, so this I.P.should never be assigned, let alone in duplicate.I Google this topic before posting, and it was suggested that IPv6 could be having an adverse affect. I determined this because I performed a ping on the laptop and only got a MAC address back rather than an I.P. address.However after unticking IPv6, and rebooting, the laptop is still causing havoc.I can set a static I.P. address on the laptop, however this is not ideal.
View 2 Replies
View Related
Oct 12, 2011
We once had a virtual server with two network adapters, one was internal and the other was external, and people could access it directly from the internet.
That server recently, died (someone put the .VHD file on a massive RAID 0 array, and that went boom), and I need to set it back up again. All the DNS entries appear to still be there, but how to assign the external IP to the network adapter. I tried Google, but my Google-fu must be weak today as I can't find anything useful.
It's a Server 2008 R2 machine running inside Hyper-V. Nothing's changed except for the new Windows install, it's running with the exact same VM settings, which I didn't touch except to add a new VHD.
View 5 Replies
View Related
Jun 25, 2011
I just got a brand new laptop and I can't get it to connect to LAN.It's plugged in to the same hub as my main machine and I can't even access my router UI.It's not the cable because I tried plugging in my main machine's cable to the new laptop and the same thing happens.ipconfig reveals an Autoconfiguration IPv4 Address of: 169.254.197.187 But that number should say 192.168.1.1xx I've tried uninstalling and reinstalling the Ethernet driver as well.I've tried resetting the router and modem.I've tried resetting TCP/IP.
View 13 Replies
View Related
Jul 25, 2012
My company wants to create a VPN Tunnel to allow a remote office to connect to ours. I purchased 2 ASA 5505 and I was expecting to be able to set this up without any issues. Sadly, that is not the case.
What I'm having trouble with is configuring my Public IP Address to the device. I go through the setup wizard and enter the IP Address like normal, but I have no option to input my ISP's subnet, Gateway or DNS. Without those, I get no internet connection. I know there is a way to do this, but I'm stumped.
My Specs:
2 ASA 5505 series
ISP Modem (Which they control) - SMC SMCD3GN with DHCP disabled
View 1 Replies
View Related
Oct 25, 2012
hrome threw me a DNS lookup failed. I go into my network settings and I noticed that I had limited connectivity. It would switch between no network access and no internet access every few seconds. After a bit of fiddling around, I got it to connect through assigning myself a static IP. This isn't exactly convenient because I use this computer on multiple networks. When I try to have it on automatic IP, I get no IP address or default gateway when I do an ipconfig /all. It would appear that my router quit assigning my laptop an IP for no reason whatsoever. DHCP is enabled on the router, and all other devices work fine. What could possibly be the problem here? I'm 99% sure it's not an IP conflict either. It's not being MAC filtered because I'm on the thing right now posting this through a static IP. It's not my A/V because it's worked great in the past. Perhaps I should also mention it occasionally says "unidentified network" instead of the SSID
View 8 Replies
View Related
Jan 22, 2012
I'm fairly new to Cisco configuration and I am looking at a problem for a client that involves the use of a Cisco 887 (wired only) as the main router/gateway. The problem I am investigating involves the allocatoni of DHCP addresses from the device to a product we have designed that connects to the router. I am attempting to set the 880 up on the bench with no ADSL connection and just use the DHCP feature of the box for the 4 switch ports on the back. I have tried all kinds of configurations from default. Whatever I do I can't get the router to assign an IP address to anything that is plugged in (Windows or Linux machines). What could I be doing wrong ? It can't be that difficult to get the system to just act as a DHCP server.
View 2 Replies
View Related
May 20, 2012
The problem is WAP 610n not assigning IP address through DHCP; i have to add IP address mannualy.
just go through the details below:
In my network environment we are using :
CISCO Router 800 series; IP: 192.168.1.1
Domain server with DHCP server : 192.168.1.2
DHCP pool: 192.168.1.234 - 192.168.1.250
WAP IP : 192.168.1.236
WAP configuration :
configuration view : mannual
Wireless band : 2.4 Ghz
Network mode : mixed
channel width: 20 Mhz only
standard channel : auto
SSID broadcast : Disabled [ for security reason]
Security mode : WPA2 Personal
Encryption : TKIP/AES
Firmware : 1.0.01 build 94, Oct 26, 2009
Note: In status menu it is not showing any default gateway.
Encapsulation method in CISCO router : PPPoA [ as instructed by ISP]
View 5 Replies
View Related
Feb 16, 2013
some problems when I was trying to install my X3000 as a DSL modem and router.I had to assign a designated IP address but I have dynamic IP from my internet supplier. I can't get pass the stepp of assigning IP address.
View 4 Replies
View Related
Apr 9, 2012
Recently purchased 5 SGE2010P 48-port switches to replace older L2 switches. I have 4 switches in single stack and one as a standalone. Both the stack and standalone will connect to at least 1 Dell 2724 switch. Both the stack and the standalone Cisco are in Layer 3 mode.
I have created several VLans on the Cisco switches, and am trying to assign an IP address to the VLan, but cannot seem to figure out the web gui. Each time I try to use Systems > System Management > IP Addressing > IP Interface, then click Add, it simply changes the existing IP of the management interface. So, I'm not sure how to go about assigning an IP Address to an Vlan.
View 15 Replies
View Related
Nov 20, 2011
The DHCP/DNS server is on ip address 10.1.100.103 with an alt on .102 I'm attempting to integrate a 4510R+E into an existing network and use existing DHCP/DNS windows 2008 server to push out IP addresses to connected computers.
I want to assign a VLAN to every port for management purposes and then I put an IP helper address on every VLAN.
I've attached a the 4500E partial config. I'm attempting to get Gi1/44 to a state where I can plug a computer into it an resolve an ip address and gain internet access like all the devices on the existing network can do.
I've created a new scope in DHCP with the ip subnet of 10.60.211.0 255.255.255.0 It leases addresses from .1 to .253
The computer will not resolve ip addresses with this config.
View 5 Replies
View Related
Sep 15, 2011
Since I have static ip I cannot use the printer Brither Model.I have U verse system from At&t and I have gotten static IPs to be able to install an IPcamara and to access it from any point in the world. But since I have gotten the static IPs I had a problem with my printer, also the i phone,and I pad do not connect to internet but the windows lap tops are working fine with the wifi.
View 1 Replies
View Related
Jul 18, 2011
I want to print via Windows to a static-ip hp printer over the internet. I have static-ip addressed printers and plotters that I need to print to via my laptops from various locations when i'm not in the office. I have three locations and each location has static-ip's assigned to the local printers and i need to be able to print to them.Most laptops are either Windows XP PRO or Windows 7 Home Premium. I have heard something about using port 9100 to print to them, but I don't know how that works.
View 3 Replies
View Related
Jan 8, 2011
For some reason, our router donwstairs was kicking one or more of our (4pc's downstairs, one occasionally upstairs) off. My son connected another router upstairs and then created a static IP for everything. It seems when he did that, our Brother 2170 wireless printer quit working. We've tried everything to get it going again and nothing works- even Brother didn't get it rectified. Earlier today, my son finally got it working, connected directly to the router to get the static IP on the printer (I guess). But when he disconnected it (hardwired) from the router, it won't work again
View 5 Replies
View Related
Mar 15, 2013
I have two different locations, two different ISP�s .
Cable �Modem--------Linksys Router WRT54G
DSL-Modem----------Linksys Router WRT54GS
One computer (Windows 7 Laptop) which travels between both locations.Can I or how do I setup a static IP address for both locations on my computer and not have to change settings when I change locations?
View 1 Replies
View Related
Jul 11, 2011
I am connected to a static ip network. This network sets local ips to connected computers but general ip is the same: static ip of network. When i go to "whatismyipaddress", I can see this static ip. I want to change my ip address. I have no chance to use proxy server or router connection. Is there a way to change my ip address? (Because some sites ban ip address, ex:rapidshare etc. and I need to change my ip)
View 1 Replies
View Related
Feb 24, 2011
Everytime I start one of my two Windows machines, I need to go to the control panel network adapter and enter the static IP address in the IPV4 properties. It is always blank after a shutdown.I have two machines that are networked for flight simming.One of the machines must have a static IP so I configured both static. Not sure if this has anything to do with my problem.
View 5 Replies
View Related
Feb 7, 2011
A business network has had a Static IP Address for several years. Recently, something caused the settings to be changed to "Obtain an IP Address Automatically". As a result, pcAnywhere will no longer connect, and this is a critical function of the office. This has to get fixed. I've attempted to put the settings back to what they were (The IP Address, Subnet Mask, Default Gateway, etc...) but now the Server will no longer connect to the internet when you setup the Static IP. The settings I am using are exactly the same as the ones from over 2 years ago. Now they no longer work, and networking is confusing to me.
View 4 Replies
View Related
Jun 10, 2012
I've had the same IP address for years and want to change it to a new one - I have a dynamic IP but for some reason it will never change.It looks as if it's always static-what settings I need to change on Windows 7 to get it to roll over onto a new IP address?
View 1 Replies
View Related
Jan 24, 2012
how to connect a different ip addressing single system in different place. but we cann't change the ip address in manually
View 1 Replies
View Related
May 13, 2013
Right now I have a lab setup with a couple of these AP's.They are both doing DHCP to get their IP address from a 5508.How do I set a static IP address on the AP?
View 5 Replies
View Related
Oct 6, 2011
need to understand about IP addressing on printer. At work, we have printers with NIC. When the printer was installed first time, I printed the configuration and noticed the printer IP starts with 192.xxx.xxx.xx but when the computer person in-charge installed it the printer IP
[code]...
View 3 Replies
View Related
Nov 16, 2011
ok the connection is a dial up it doesn't give any static ip address when i connect it now it will give me different ip , when i disconnect it again it will give me another ip. an the message appear at the server and the affect the client.....the client are using satic ip address.
View 1 Replies
View Related
Jan 29, 2012
how to open a site by using static ip address
View 2 Replies
View Related
Apr 20, 2011
I have what I feel is sort of a strange issue. When I have systems on my home network get their IP from DHCP, they can get to the internet just fine. But it seems that when I assign a static address, they have local network access only, and will not get a connection to the internet. My windows 2008 server is the big problem with this one.
View 10 Replies
View Related
Aug 3, 2012
When I was hosting a server on minecraft, a few people complained that the server was down. It was, and the problem is that my router switched to a dynamic IP after comcast installed a security system to my house. If I try to reset the router, the system goes down and takes a helluva long time to get back up. Whenever I try to switch to a static IP, however, I lose internet connection. Wondering how to fix this. Or do I have to switch back to my laptop - which might also not even work. (I'll go try that, but I'm using my desktop because it has extra RAM.)
View 19 Replies
View Related
Mar 23, 2012
Do not have internet connectivity, despite all the lights lit on calbe modem and the ASUS WL520GU router and only the internet and ethernet lights are lit on the Linksys 2102.Despite numerous reboots, no change and even bypassing the router and connecting directly to ATA still no conectivity.When I open a browser, it reverts to the Asus error page, "reason for failed connection: You have set the wrong dynamic or static IP address, though nothing was changed.Funny thing again, a direct internet connection to the ATA did nothing.A google search only just shows lots of unasnered posts on this issue, or only the usual 'please reboot'.
View 9 Replies
View Related
Jun 29, 2012
do internet cafes use static ip or dynamic ip address. Also what would be the benefit if they used a static ip address.
View 1 Replies
View Related
