Cisco :: 5508 How To Set A Static IP Address On AP
May 13, 2013Right now I have a lab setup with a couple of these AP's.They are both doing DHCP to get their IP address from a 5508.How do I set a static IP address on the AP?
View 5 Replies
ADVERTISEMENT
Cisco Wireless :: 5508 Static IP Address For Guest Wired Network
Dec 4, 2012I setup a guest wired network on the WLC 5508 with 7.2.110. A postage machine can only be setup for static IP address over guest wired network. Is any one how to get it configure on the WLC 5508?
View 3 Replies View RelatedCisco :: Allowing Only Static IPs On 5508 Controller?
Nov 29, 2012We have a customer that is looking to allow only static IP addresses onto the wireless network via the new 5508 we are putting into place. I can see where to require DHCP but not the opposite.
View 4 Replies View RelatedAssigning Static IP Address?
May 26, 2012I am trying to give an static ip address to a time clock on my network and for some reason when I connect time clock to network it will always get an ip address from a different network. for example my computer IP address is 192.168.2.70 when connected to network, my default gateway is 192.168.2.1, the IP address that the time clock always gets is 192.168.1.120, there is no way to tell the time clock what IP address I wanted to be it has to get it from router (that is what the manufacturer told me), router (16portLiksys) does not have DHCP enabled the guy who set up network left it disabled, on his notes he says server (dell server T110) is acting as router is that true that a server can be acting as router?what do guys think is going on here?all the computers hooked up to network have static IP address.I also notice that when I connect a computer to router it will get an IP address from different network the same as time clock.I tried to reserve ip address on router by entering MAC address from time clock but it won't work. I am not very familiar with the server settings I have not try changing settings on server, I am not even sure the guy who set up network is right about using server as router.
View 1 Replies View RelatedTwo Static IP Address / One Computer?
Mar 15, 2013I have two different locations, two different ISP�s .
Cable �Modem--------Linksys Router WRT54G
DSL-Modem----------Linksys Router WRT54GS
One computer (Windows 7 Laptop) which travels between both locations.Can I or how do I setup a static IP address for both locations on my computer and not have to change settings when I change locations?
Cisco WAN :: 892 / Static Ip Address Assigned To The Interface?
Feb 7, 2012configure my cisco 892 router want a static ip address assigned to the interface because and I have no more internet on the router because am working on my network academy for CCENT?
View 28 Replies View RelatedCisco VPN :: ASA5500 Static Address For Vpn User
Apr 10, 2011I am trying to configure ASA to assign same static ip address to certain user(User1) every time when he connect to network via AnyConnect client. We have Windows AD and use LDAP AAA server for authentication of VPN Remote Access users. I found in document "Cisco ASA 5500 Series Configuration Guide using the CLI, 8.2" in section "Configuring an External Server for Security Appliance User Authorization" explanation and configured ASA and User Properties in AD on exectly same way:First, I assigned static ip address in properties menu(dial in section) of User1 in Active Directory. Then I created ldap attribute map where I mapped msRADIUSFrameIPAddressattribute to IETF-Radius-Framed-IP-Address attribute. At the end I applied this ldap attribute map to AAA server group LDAP.
Although I set this up, whenever I connect using User1 credentials from AD I still get ip address from vpn pool instead static ip address that I configured. In output of debug ldap 255 command I found line "msRADIUSFramedIPAddress: value = -1062718956" but not any line that prove mapping above mentioned attributes.It seems like mapping is not working.All AnyConnect users get parameters from defined internal group policy on ASA,including addresses form pool,dns server etc. I want that User1 get static ip address and inherit all other parameters from group policy.
Cisco Switches :: SG200-8 Static Mac Address
Apr 22, 2013My second problem with sg200-08 (firmware: SG200-08x_FW_1.0.6.2.stk) is when I try to add specific MAC address as secure:MAC Address Tables - Static Addresses - Add; insert vlan id, port, mac address and select "Secure":I get error message: "Error: Failed to Add 'Static Address' entry.
View 3 Replies View RelatedChanging IP Address In Static Network?
Jul 11, 2011I am connected to a static ip network. This network sets local ips to connected computers but general ip is the same: static ip of network. When i go to "whatismyipaddress", I can see this static ip. I want to change my ip address. I have no chance to use proxy server or router connection. Is there a way to change my ip address? (Because some sites ban ip address, ex:rapidshare etc. and I need to change my ip)
View 1 Replies View RelatedAssigning A Static Address To A Printer?
Jan 7, 2013HP wifi printers (I've had 2 over the last several years)eventually have a disconnect with my wifi router and was told (by an experienced IT guy from my last job) I should assign the printer a static address to eliminate the problem. How can I assign a static address to my printer. Here are the models Router: Belkin model F5D9231-4v1(01); Printer HP Officejet 6600. I know how to access the printer and manually enter an IP address and subnet and such, I just don't know which numbers to use where. I also know how to access my router, via typing in the IP address in Internet Explorer, but i'm unsure of which tab within the router's page (i.e. is it category wirelessunder MAC address control) or which numbers (IP address or MAC Address)and where should I get the correct numbers from (i.e. go run, cmd,IPconfig/all).
View 6 Replies View RelatedStatic IP Address Entry Will Not Save?
Feb 24, 2011Everytime I start one of my two Windows machines, I need to go to the control panel network adapter and enter the static IP address in the IPV4 properties. It is always blank after a shutdown.I have two machines that are networked for flight simming.One of the machines must have a static IP so I configured both static. Not sure if this has anything to do with my problem.
View 5 Replies View RelatedStatic IP Address No Longer Connects
Feb 7, 2011A business network has had a Static IP Address for several years. Recently, something caused the settings to be changed to "Obtain an IP Address Automatically". As a result, pcAnywhere will no longer connect, and this is a critical function of the office. This has to get fixed. I've attempted to put the settings back to what they were (The IP Address, Subnet Mask, Default Gateway, etc...) but now the Server will no longer connect to the internet when you setup the Static IP. The settings I am using are exactly the same as the ones from over 2 years ago. Now they no longer work, and networking is confusing to me.
View 4 Replies View RelatedChanging Static IP Address On Windows 7 To A New One?
Jun 10, 2012I've had the same IP address for years and want to change it to a new one - I have a dynamic IP but for some reason it will never change.It looks as if it's always static-what settings I need to change on Windows 7 to get it to roll over onto a new IP address?
View 1 Replies View RelatedConnect The Different Static Ip Address In Single Pc?
Jan 24, 2012how to connect a different ip addressing single system in different place. but we cann't change the ip address in manually
View 1 Replies View RelatedCisco Firewall :: 5520 Static NAT And Same IP Address For Two Interfaces
May 28, 2012We have a Cisco ASA 5520 and in order to conserve public IP addresses and configuration (possibly) can we use the same public IP address for a static NAT with two different interfaces? Here is an example of what I'm refering too where 10.10.10.10 would be the same public IP address.
-static (inside,Outside) 10.10.10.10 access-list inside_nat_static_1
-static (production,Outside) 10.10.10.10 access-list production_nat_static_1
Cisco :: AIR-LAP-1242G APs Not Obeying Static IP Address Assignment
Feb 8, 2011I've got a network of several AIR-LAP-1242G LWAPP access points controlled by a 2112 WLC. I assign static IP addresses to each LWAPP, but every few weeks, a couple of them (at random) revert back to grabbing a DHCP-assigned dynamic address for themselves, despite the fact that they're supposedly solidy configured to have static IPs. What's going on here? Is this a bug in their firmware or the WLC's firmware? If I reboot the APs, then they come up with their static IPs, but after running some random number of days/weeks, will spontaneously change their own management IP addresses and grab a DHCP address for themselves.
The 1242G APs version numbers reported by the WLC's web GUI are:
"Software version" 5.2.193.0
"Boot version" 12.4.13.0
"IOS version" 12.4(18a)JA2
"Mini IOS version" 3.0.51.0
The 2112 WLC is running software version 5.2.193.0
Cisco Firewall :: ASA 5505 - Public Static IP Address And DMZ
Feb 3, 2013I have ASA 5505 with basic licence, v9.1, ASDM 7.1. I want to create the DMZ for a web server.
The interface 0 is for the outside network The interface 6 is for the DMZ All other interfaces are for the inside network
My ISP provided me with one public static IP address, one gateway address and a subnet mask 255.255.255.252
1/ I would like to ask which interface I should assign the public static IP address to. Should it be assigned to the outside interface 0, or should it be assigned to the DMZ interface 6, while outside interface would be configured to use DHCP?
I tried to assign the static IP address to the outside interface first, but then when I used ASDM the “Public Servers” feature to configure NAT, I get error message that the outside interface and the public address cannot have the same IP address.
2/ For the sake of peace of mind, I am thinking about using the second firewall, which would be used only for the inside network. Can I connect this second firewall to one of the inside interfaces of the 1st firewall,
Cisco Routers :: Static IP Address For WRV210 Wireless
Nov 6, 2011I recently switched operating systems from XP to Windows 7. Since that time whenever I need to reboot the router, it does not recognize my printer. How do I set the router to a static ip address and will that affect its recognition of my computer? I have had no problems with computer recognition, only printer.
View 3 Replies View RelatedCisco WAN :: Configure 861 Router For Internet Using Static Ip Address?
Apr 5, 2013I am having a cisco 861 series router.The Cable from the isp was connected to fastethernet4(wan port)
Following are my isp details
IP address:172.16.62.130
subnet:255.255.0.0
default gate way:172.16.62.1
dns primary:202.153.32.2
secondary:202.153.32.3
How do i configure this details in the router and access the internet in my devices.
i want the network to be in 192.168.1.0 to 254.
how do i configure my router with this details using cisco configuration professional
Cisco Routers :: Configure SRP527w Without Static Outside Ip Address
Jul 17, 2010I need to know how to configure SRP527w without a static outside ip address to establish a VPN tunnel with VPNC3000.
View 31 Replies View RelatedDial Up Doesn't Give Any Static IP Address?
Nov 16, 2011ok the connection is a dial up it doesn't give any static ip address when i connect it now it will give me different ip , when i disconnect it again it will give me another ip. an the message appear at the server and the affect the client.....the client are using satic ip address.
View 1 Replies View RelatedBroadband :: Opening Site By Using Static Ip Address
Jan 29, 2012how to open a site by using static ip address
View 2 Replies View RelatedNo Internet Connection When Assign Static Address
Apr 20, 2011I have what I feel is sort of a strange issue. When I have systems on my home network get their IP from DHCP, they can get to the internet just fine. But it seems that when I assign a static address, they have local network access only, and will not get a connection to the internet. My windows 2008 server is the big problem with this one.
View 10 Replies View RelatedStatic IP Address Causes Computer To Disconnect From Internet
Aug 3, 2012When I was hosting a server on minecraft, a few people complained that the server was down. It was, and the problem is that my router switched to a dynamic IP after comcast installed a security system to my house. If I try to reset the router, the system goes down and takes a helluva long time to get back up. Whenever I try to switch to a static IP, however, I lose internet connection. Wondering how to fix this. Or do I have to switch back to my laptop - which might also not even work. (I'll go try that, but I'm using my desktop because it has extra RAM.)
View 19 Replies View RelatedError - Wrong Static Or Dynamic IP Address?
Mar 23, 2012Do not have internet connectivity, despite all the lights lit on calbe modem and the ASUS WL520GU router and only the internet and ethernet lights are lit on the Linksys 2102.Despite numerous reboots, no change and even bypassing the router and connecting directly to ATA still no conectivity.When I open a browser, it reverts to the Asus error page, "reason for failed connection: You have set the wrong dynamic or static IP address, though nothing was changed.Funny thing again, a direct internet connection to the ATA did nothing.A google search only just shows lots of unasnered posts on this issue, or only the usual 'please reboot'.
View 9 Replies View RelatedDo Internet Cafes Use Static Or Dynamic IP Address
Jun 29, 2012do internet cafes use static ip or dynamic ip address. Also what would be the benefit if they used a static ip address.
View 1 Replies View RelatedCisco :: BGP Aggregate-address Versus Static Summary Route
Sep 16, 2012I have a layer 3 switch with a bunch of SVIs all in the 192.168.x.0/24 range. I just want to advertise a 192.168.0.0/16 summary to the BGP neighbors. I can do this either by:
1) Redistributing connected into BGP and then using the 'aggregate-address' command to advertise the summary.
2) Specifying a network statement in the BGP config for every single SVI, then using the 'aggregate-address' command.
3) Create a static route to null0 (ip route 192.168.0.0 255.255.0.0 null0) and put 'network 192.168.0.0 mask 255.255.0.0' command in the BGP config.All three fulfill the same purpose of summarizing all the SVIs, but creating the static route is much cleaner in this case. It seems like the aggregate-address command is mostly intended for routers that are aggregating connections coming from other routers and all of them share a common prefix.
Cisco Firewall :: ASA 5505 / Create A Static Ip Address Under Version 8.4?
Mar 20, 2012I just upgraded my firewall to ASA 5505. Now, my original static ip address cofiguration is gone. Apperantly, Cisco went away from static ip address to something like nat (inside,outside) dynamic interface. how to create a static ip address under version 8.4? By the way, I am sharing what my configuration used to look before upgrading.
!
hostname cisco-asa
domain-name default.domain.invalid
names
!
interface Vlan1
nameif inside
security-level 100
[code].....
Cisco VPN :: ACS 5.2 Create Static IP Address User For Remote Access
Sep 15, 2011At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I can't find it.I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this: [code] I do this,but it's not work.When I use EasyVPN client to connect ASA 5520,user could through authentication but will not get that static IP address which I configuration on Internal Users.so,what should I do,if anyboby knows how to use ACS 5.2 to create a static ip address user for remote access VPN.
View 2 Replies View RelatedCisco Firewall :: 6552 Static Entries With Same Ip Address But Different Ports
Sep 15, 2011Our proxy/anti-smap/IPS box called PROXY is behind our Cisco ASA firewall. The PROXY is set in transparent mode.The PROXY internal ip is 1.1.1.1 (internal ip)We have the MX record for mail.domain.com with public ip 9.2.7.5 (public ip as we entered with ISP public DNS)What happens now is that the emails that come through get "caught" by the PROXY and then we setup a thing whereby the emails are then forwarded from PROXY to our mail.domain.com server. Also, we made a static entry in PROXY whereby we can https to our email server for the outlook web access from outside of work therefore allowing for users to see the outlook web access web page.On the Cisco firewall, we put the static entry that 9.2.7.5 is mapped to 1.1.1.1 thus the mail server public ip is mapped to the PROXY.
Now, the box has this thing whereby it sends an email to all staff once a day telling them how many mails are legit, how many rejected and how many are spam - the spam emails are listed within the email and staff can at a click of a release button next to each spam email release a particular email from the PROXY box and make it to into their inbox. This works fine from the inside network, but I have issues from the outside due to the DNS and other things.I also put in the PROXY that any network can release spam and that our staff vlan can release emails. Also, on the inside of the firewall we did an access list that computers from staff vlan can access 1.1.1.1 on port 6552 (Which is the release spam port).Hence, we can release emails from internal network through the Microsoft Outlook.
On the outside network, we cannot release emails when using outlook web access.The host name for the PROXY release spam is proxy.domain.com so what we did also today is ask "ISP" to make an A record entry for another public ip which is 9.2.7.6 for proxy.domain.com.We meanwhile made an entry on the access list that comptuers from outside can access 9.2.7.6 on port 6552 (which is the release port).Now the only question is in regards to the static entries:
1. do we (and can we?) static map 9.2.7.6 to 1.1.1.1 through a port 3840 on the Cisco ASA (although we have already mapped 1.1.1.1 to 9.2.7.5 - I have a doubt here as this might mean we might not get emails? Or would we have to do the static again for this one specifcying the 9.2.7.5 as an smtp entry and the 9.2.7.6 as a release button?
2. have I made a mistake in general and should I have just told the ISP to make a CNAME entry for proxy.domain.com with the public ip 9.2.7.5 (which is the public ip for MX record?)?
Cisco Firewall :: ASA 8.3(2) / PAT Interface Address With Static NAT Port Translation?
Aug 22, 2011I have an 8.3(2) ASA with a single outside IP. Dynamic PAT translates inside addresses to the outside interface address. I would like to use static NAT with port translation to access an inside syslog server. I got an error when I tried using the outside interface address. Can I use both dynamic PAT and Port Translation with the same outside address?This is what I would like to use but I receive an error saying there is an overlap using the outside interface address.(192.168.1.0 is my inside network. 10.10.1.10 is the outside interface IP.)
object network inside-net
subnet 192.168.1.0 255.255.255.0
nat (inside, outside) dynamic interface
object network SYSLOG_SERVER
host 192.168.1.50
nat (inside,outside) static 10.10.1.10 service tcp ssh ssh
Cisco VPN :: Configure Static IP Address In Remote Client ASA 5500?
Aug 13, 2011i am trying to configure static ip on remote client user side , i am using the following doc as an example but i am not getting the ip which i am mentiong in the user .[url]...
View 10 Replies View RelatedCisco :: Windows 7 2008 Duplicate Static Address When Using 3750
Apr 30, 2013ISE 1.1.3
Cisco 3750 switches
Windows XP / 7 / 2008 clients
I'm having some weird issues were if a client connects to a switchport and happens to be using a static IP address then the client warns of a duplicate address problem. Also the client will then only show the default gateway within ipconfig even though the IP address / mask is still in the GUI network properties of the adaptor. This is happening with Windows 7 and Windows 2008 devices.
Windows XP clients don't get the issue.
Some clients will use 802.1x native supplicant and some will be authenticated based on MAB. Not noticed the problem with 802.1x clients but it always occurs on MAB.
I came across a similar issue here: URL
Going of that blog I tried using the "ip device tracking delay probe delay" command but the switches don't recognise the "delay" keyword.
The switches are 3750 switches running version 12.2(58)SE2.
All I have is "count, interval, use-svi" as extra options.
Catalyst 4500 switch guide has "delay" option but no "count, interval or use-svi".
The only way I have managed to avoid the problem is using the second solution which is a registry hack on each client. This is fine for the odd server but not realistic when there will be hundreds of other clients.