I have two different locations, two different ISP�s .
Cable �Modem--------Linksys Router WRT54G
DSL-Modem----------Linksys Router WRT54GS
One computer (Windows 7 Laptop) which travels between both locations.Can I or how do I setup a static IP address for both locations on my computer and not have to change settings when I change locations?
When I was hosting a server on minecraft, a few people complained that the server was down. It was, and the problem is that my router switched to a dynamic IP after comcast installed a security system to my house. If I try to reset the router, the system goes down and takes a helluva long time to get back up. Whenever I try to switch to a static IP, however, I lose internet connection. Wondering how to fix this. Or do I have to switch back to my laptop - which might also not even work. (I'll go try that, but I'm using my desktop because it has extra RAM.)
View 19 Replies View RelatedWe have an ADSL connection and use a D-Link DSL-320B modem. We have a D-Link DIR-120 router connected to this modem. This has worked perfectly fine up until today when we disconnected the router and connected a computer (call it A) directly to the modem because it was getting an unusable connection through the router for some reason. We later also performed a factory reset on the DIR-120 router.
Unfortunately, after the above steps the router did not receive any IP address (through DHCP) from the ADSL connection anymore. During my attempts to debug this I noticed that my laptop (call it B) didn't get any IP address either (when connected directly to the modem). I noticed the following syslog entries repeating over and over while trying to connect: [code]
At this point computer A could still get a connection just fine tho (when connected directly to the modem).
I then tried to change the MAC address of the router to an arbitrary one (a copy of computer B's MAC address but with the last digit increased by one). The router still did not get assigned any IP address. Finally I tried making the router clone the MAC address of a third computer (call it C). C has never been connected directly to the modem. Doing this worked. After cloning the MAC address of computer C the router is immediately assigned an IP address and the internet connection works as it did prior to all this.
Now, my question is, why would computer B and the original MAC address of the router not be able to get an IP address while two other computers worked just fine? Why would changing to an arbitrary MAC address not work while cloning the MAC address of another computer did? Could the router's MAC address have been blocked by the ISP for some reason (and what could cause this)?
but my situation seems more like a blacklisting of some MAC addresses rather then allowing just a single MAC address.
I got a static ip from my isp. I set up my static ip manually through my linksy router. I need the static ip to connect to a private network for my new job but cant connect to that network. I went to whatsmyip and found that my old dynamic ip is still showing up externally, it looks like my ip4 is using the dynamic as a preferred. My question is do i need to manually change the network connection on my LAN and wireless connection under ipv4 to change it from automatically obtain TO use the following address and put in my static? And do I have to change the DNS also? I am on a home network with one desktop on vista home premium and laptop windows 7.
View 5 Replies View Relatedprevent someone from putting their computer on a network with a static ip that is already on the network so it does not cause a conflict. I'll try to do the short version of what happeend (ip numbers wont be accurate) has his laptop with him set to a static ip of 192.168.0.1 and connects it to our network and our file server which is also the dhcp and dns is set to that ip address. So when he connected it it basically brought down our whole network....
View 2 Replies View RelatedI am trying to give an static ip address to a time clock on my network and for some reason when I connect time clock to network it will always get an ip address from a different network. for example my computer IP address is 192.168.2.70 when connected to network, my default gateway is 192.168.2.1, the IP address that the time clock always gets is 192.168.1.120, there is no way to tell the time clock what IP address I wanted to be it has to get it from router (that is what the manufacturer told me), router (16portLiksys) does not have DHCP enabled the guy who set up network left it disabled, on his notes he says server (dell server T110) is acting as router is that true that a server can be acting as router?what do guys think is going on here?all the computers hooked up to network have static IP address.I also notice that when I connect a computer to router it will get an IP address from different network the same as time clock.I tried to reserve ip address on router by entering MAC address from time clock but it won't work. I am not very familiar with the server settings I have not try changing settings on server, I am not even sure the guy who set up network is right about using server as router.
View 1 Replies View RelatedI am connected to a static ip network. This network sets local ips to connected computers but general ip is the same: static ip of network. When i go to "whatismyipaddress", I can see this static ip. I want to change my ip address. I have no chance to use proxy server or router connection. Is there a way to change my ip address? (Because some sites ban ip address, ex:rapidshare etc. and I need to change my ip)
View 1 Replies View RelatedHP wifi printers (I've had 2 over the last several years)eventually have a disconnect with my wifi router and was told (by an experienced IT guy from my last job) I should assign the printer a static address to eliminate the problem. How can I assign a static address to my printer. Here are the models Router: Belkin model F5D9231-4v1(01); Printer HP Officejet 6600. I know how to access the printer and manually enter an IP address and subnet and such, I just don't know which numbers to use where. I also know how to access my router, via typing in the IP address in Internet Explorer, but i'm unsure of which tab within the router's page (i.e. is it category wirelessunder MAC address control) or which numbers (IP address or MAC Address)and where should I get the correct numbers from (i.e. go run, cmd,IPconfig/all).
View 6 Replies View RelatedEverytime I start one of my two Windows machines, I need to go to the control panel network adapter and enter the static IP address in the IPV4 properties. It is always blank after a shutdown.I have two machines that are networked for flight simming.One of the machines must have a static IP so I configured both static. Not sure if this has anything to do with my problem.
View 5 Replies View RelatedA business network has had a Static IP Address for several years. Recently, something caused the settings to be changed to "Obtain an IP Address Automatically". As a result, pcAnywhere will no longer connect, and this is a critical function of the office. This has to get fixed. I've attempted to put the settings back to what they were (The IP Address, Subnet Mask, Default Gateway, etc...) but now the Server will no longer connect to the internet when you setup the Static IP. The settings I am using are exactly the same as the ones from over 2 years ago. Now they no longer work, and networking is confusing to me.
View 4 Replies View RelatedI've had the same IP address for years and want to change it to a new one - I have a dynamic IP but for some reason it will never change.It looks as if it's always static-what settings I need to change on Windows 7 to get it to roll over onto a new IP address?
View 1 Replies View Relatedhow to connect a different ip addressing single system in different place. but we cann't change the ip address in manually
View 1 Replies View RelatedRight now I have a lab setup with a couple of these AP's.They are both doing DHCP to get their IP address from a 5508.How do I set a static IP address on the AP?
View 5 Replies View Relatedok the connection is a dial up it doesn't give any static ip address when i connect it now it will give me different ip , when i disconnect it again it will give me another ip. an the message appear at the server and the affect the client.....the client are using satic ip address.
View 1 Replies View Relatedhow to open a site by using static ip address
View 2 Replies View RelatedI have what I feel is sort of a strange issue. When I have systems on my home network get their IP from DHCP, they can get to the internet just fine. But it seems that when I assign a static address, they have local network access only, and will not get a connection to the internet. My windows 2008 server is the big problem with this one.
View 10 Replies View RelatedDo not have internet connectivity, despite all the lights lit on calbe modem and the ASUS WL520GU router and only the internet and ethernet lights are lit on the Linksys 2102.Despite numerous reboots, no change and even bypassing the router and connecting directly to ATA still no conectivity.When I open a browser, it reverts to the Asus error page, "reason for failed connection: You have set the wrong dynamic or static IP address, though nothing was changed.Funny thing again, a direct internet connection to the ATA did nothing.A google search only just shows lots of unasnered posts on this issue, or only the usual 'please reboot'.
View 9 Replies View Relateddo internet cafes use static ip or dynamic ip address. Also what would be the benefit if they used a static ip address.
View 1 Replies View Relatedconfigure my cisco 892 router want a static ip address assigned to the interface because and I have no more internet on the router because am working on my network academy for CCENT?
View 28 Replies View RelatedI am trying to configure ASA to assign same static ip address to certain user(User1) every time when he connect to network via AnyConnect client. We have Windows AD and use LDAP AAA server for authentication of VPN Remote Access users. I found in document "Cisco ASA 5500 Series Configuration Guide using the CLI, 8.2" in section "Configuring an External Server for Security Appliance User Authorization" explanation and configured ASA and User Properties in AD on exectly same way:First, I assigned static ip address in properties menu(dial in section) of User1 in Active Directory. Then I created ldap attribute map where I mapped msRADIUSFrameIPAddressattribute to IETF-Radius-Framed-IP-Address attribute. At the end I applied this ldap attribute map to AAA server group LDAP.
Although I set this up, whenever I connect using User1 credentials from AD I still get ip address from vpn pool instead static ip address that I configured. In output of debug ldap 255 command I found line "msRADIUSFramedIPAddress: value = -1062718956" but not any line that prove mapping above mentioned attributes.It seems like mapping is not working.All AnyConnect users get parameters from defined internal group policy on ASA,including addresses form pool,dns server etc. I want that User1 get static ip address and inherit all other parameters from group policy.
My second problem with sg200-08 (firmware: SG200-08x_FW_1.0.6.2.stk) is when I try to add specific MAC address as secure:MAC Address Tables - Static Addresses - Add; insert vlan id, port, mac address and select "Secure":I get error message: "Error: Failed to Add 'Static Address' entry.
View 3 Replies View RelatedIn my router I can set rule that all traffic incoming to router's extAddr:8888, is forwarded to my intAddr:8888. But I also need reverse rule that packets originating from intAddr:8888 are translated to extAddr:8888. Can I do that? What technique can I search on google to find more information, because it is not port forwarding. I would calll it reverse port forwarding or static port address translation, but I do not find anything useful in internet searching these keywords.
View 3 Replies View Relatedusing ipconfig to show static ip address when cable is unplugged, can ipconfig show static ip address when cable is unplugged? if no why? and if yes how do you make it work? anything you can edit on registry to mke it work.
View 2 Replies View RelatedI have 3 Dcs-3420's on the same network same static ip setup and they never have issues. Im testing 1 942L, I've upgraded firmware to1.11, but periodically the camera loses its ip address which is weird because it is set static. My wireless is set to Mac address security. Now camera is outside in a shaded area, over night the camera worked all night, this morning it has reset three times. Additionally, each time it resets/losses ip address it also loses the manually set time.
View 1 Replies View RelatedWe have a Cisco ASA 5520 and in order to conserve public IP addresses and configuration (possibly) can we use the same public IP address for a static NAT with two different interfaces? Here is an example of what I'm refering too where 10.10.10.10 would be the same public IP address.
-static (inside,Outside) 10.10.10.10 access-list inside_nat_static_1
-static (production,Outside) 10.10.10.10 access-list production_nat_static_1
I've got a network of several AIR-LAP-1242G LWAPP access points controlled by a 2112 WLC. I assign static IP addresses to each LWAPP, but every few weeks, a couple of them (at random) revert back to grabbing a DHCP-assigned dynamic address for themselves, despite the fact that they're supposedly solidy configured to have static IPs. What's going on here? Is this a bug in their firmware or the WLC's firmware? If I reboot the APs, then they come up with their static IPs, but after running some random number of days/weeks, will spontaneously change their own management IP addresses and grab a DHCP address for themselves.
The 1242G APs version numbers reported by the WLC's web GUI are:
"Software version" 5.2.193.0
"Boot version" 12.4.13.0
"IOS version" 12.4(18a)JA2
"Mini IOS version" 3.0.51.0
The 2112 WLC is running software version 5.2.193.0
I have ASA 5505 with basic licence, v9.1, ASDM 7.1. I want to create the DMZ for a web server.
The interface 0 is for the outside network The interface 6 is for the DMZ All other interfaces are for the inside network
My ISP provided me with one public static IP address, one gateway address and a subnet mask 255.255.255.252
1/ I would like to ask which interface I should assign the public static IP address to. Should it be assigned to the outside interface 0, or should it be assigned to the DMZ interface 6, while outside interface would be configured to use DHCP?
I tried to assign the static IP address to the outside interface first, but then when I used ASDM the “Public Servers” feature to configure NAT, I get error message that the outside interface and the public address cannot have the same IP address.
2/ For the sake of peace of mind, I am thinking about using the second firewall, which would be used only for the inside network. Can I connect this second firewall to one of the inside interfaces of the 1st firewall,
I recently switched operating systems from XP to Windows 7. Since that time whenever I need to reboot the router, it does not recognize my printer. How do I set the router to a static ip address and will that affect its recognition of my computer? I have had no problems with computer recognition, only printer.
View 3 Replies View RelatedI am having a cisco 861 series router.The Cable from the isp was connected to fastethernet4(wan port)
Following are my isp details
IP address:172.16.62.130
subnet:255.255.0.0
default gate way:172.16.62.1
dns primary:202.153.32.2
secondary:202.153.32.3
How do i configure this details in the router and access the internet in my devices.
i want the network to be in 192.168.1.0 to 254.
how do i configure my router with this details using cisco configuration professional
I need to know how to configure SRP527w without a static outside ip address to establish a VPN tunnel with VPNC3000.
View 31 Replies View RelatedI have a layer 3 switch with a bunch of SVIs all in the 192.168.x.0/24 range. I just want to advertise a 192.168.0.0/16 summary to the BGP neighbors. I can do this either by:
1) Redistributing connected into BGP and then using the 'aggregate-address' command to advertise the summary.
2) Specifying a network statement in the BGP config for every single SVI, then using the 'aggregate-address' command.
3) Create a static route to null0 (ip route 192.168.0.0 255.255.0.0 null0) and put 'network 192.168.0.0 mask 255.255.0.0' command in the BGP config.All three fulfill the same purpose of summarizing all the SVIs, but creating the static route is much cleaner in this case. It seems like the aggregate-address command is mostly intended for routers that are aggregating connections coming from other routers and all of them share a common prefix.
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V5
Firmware Version : 5.0.0 Build 120703 Rel.29030
ISP :
I have setup some static addresses but now some of them need to change... But I can't see how to amend the DHCP table..There must be a way of doing this beyond altering the DHCP range so I can put them all in againLAN Setup.JPG.
I have a problem viewing my security cam on my android IP cam app.I forwarded port on my router to my security cam then fixed security cam to have a static IP but my computer being on DHCP, after reboot changed IP, so I lost connection to android IP cam app.I read on a forum,that If your camera is using DHCP,setup your router so that it always gives the same static IP address for the camera based on it's MAC address but where do you set this up a Linksys E1000 router & on Samsung Y? so I can view my security cam on my android IP cam app.?
View 9 Replies View Related