Cisco Routers :: Configure SRP527w Without Static Outside Ip Address
Jul 17, 2010I need to know how to configure SRP527w without a static outside ip address to establish a VPN tunnel with VPNC3000.
View 31 Replies
ADVERTISEMENT
Cisco Routers :: SRP527w Static Routes Configuration Required
Feb 20, 2012We have 2 sites with 2 internet connections at each site. All are SRP527w routers. 1 is for internet and 1 is for a site to site VPN as,Currently we are using Static Routes on the PC's so they can access each server no matter what site they are at. I have looked at using the Static Routes section on the SRP's but cannot get it to work.
View 2 Replies View RelatedCisco Routers :: To Configure Connection SDSL With SRP527W
Feb 23, 2012I have a problem to configure my connection SDSL.my router is SRP527W. my modem is Patton 3088. Do I need to update the ios? or there is a specific configuration of static IP ?
View 1 Replies View RelatedCisco Routers :: Configure A SRP527W For A Remote Site
Mar 11, 2013I am trying to configure a SRP527W for a remote site.It needs to connect back to our Central Office, (via an ASA) which has several VLANs configured. I have entered the configuration for an IKE policy, and one for an IPSec policy (I can only enter one ip/subnet per IPSec policy)When I try to create a 2nd IPSec policy, if I point to the existing IKE policy, I get an error stating "IKE policy has been used by other IPSec policy".If I try to create a new IKE policy, using a different name, but with the same parameters, it shows an error stating the policy is a replica of an existing policy.If I create a new IKE policy, but use a different pre-shared key, then it is accepted by the 2nd IPSec policy, but that would mean I would have to create 2 seperate tunnels on the ASA, each using a different pre-shared key. I have never needed to do this for any of the other routers we have connected.
View 1 Replies View RelatedCisco Routers :: SRP527W-U - Configure We Have An Ethernet Termination For WAN?
Sep 10, 2012Cisco SRP527W-U.
We would like to configure it in the following way, 1) we have an ethernet termination for the WAN 2) we have 2 different vlans going to 2 different switches.
Can we have the default gateway for 2 LAN subnets and a default route via a /30 for our WAN. Can we use the 4 switchports for this?
switchport 1 VLAN 2 (Switch 1 LAN)
switchport 2 VLAN 3 (Switch 2 LAN)
switchport 3 VLAN 4 (Link to Data centre switch with /30)
Cisco Routers :: Configuring VPN (invalid IP Address Format) With SRP527W?
Oct 24, 2011I'm tryng to configure a vpn with a cisco small business pro router, model srp527W-k9-g5 But when i try to set the “remote ip” in Remote traffic selection a I have to set (10.0.0.0) a message said:
“Invalid IP Address Format”
If i change the ip and i put 10.0.0.1 i have not error but I have to put 10.0.0.0 and if i configure it on a cisco WRV210 (por example) i have no error.
Cisco Routers :: Site-to-site VPN From SRP527W (dynamic IP) To ASA 5505 (Static)
Sep 6, 2011I have an ASA5505 running which is on a static IP. I have just got an SRP527W for a remote worker and want to create a site-to-site VPN into the ASA. I have a number of other router of non-cisco brand which just all dial-in and connect no problem.
On other routers I have been abloe to specify the DDNS hostname in the VPN setup so that the ASA can identify it. I'm not sure how I setup the SRP527 to connect to the ASA.
Cisco WAN :: Configure 861 Router For Internet Using Static Ip Address?
Apr 5, 2013I am having a cisco 861 series router.The Cable from the isp was connected to fastethernet4(wan port)
Following are my isp details
IP address:172.16.62.130
subnet:255.255.0.0
default gate way:172.16.62.1
dns primary:202.153.32.2
secondary:202.153.32.3
How do i configure this details in the router and access the internet in my devices.
i want the network to be in 192.168.1.0 to 254.
how do i configure my router with this details using cisco configuration professional
Cisco VPN :: Configure Static IP Address In Remote Client ASA 5500?
Aug 13, 2011i am trying to configure static ip on remote client user side , i am using the following doc as an example but i am not getting the ip which i am mentiong in the user .[url]...
View 10 Replies View RelatedRouters / Switches :: Configure 2 Static IPs Over Single Connection?
Jan 28, 2011This is the situation in our Lab.We have one telephone line with broadband connection and a system which is connected to a modem to use this broadband facility. Recently we have taken two static IPs over this connection for a project work.Now what I want to know is, how to configure these static IPs, so that I can connect two systems (each one to one static IP) to use these static IPs and continue to access the internet in the 3rd (already present) system.
View 7 Replies View RelatedCisco Routers :: Static IP Address For WRV210 Wireless
Nov 6, 2011I recently switched operating systems from XP to Windows 7. Since that time whenever I need to reboot the router, it does not recognize my printer. How do I set the router to a static ip address and will that affect its recognition of my computer? I have had no problems with computer recognition, only printer.
View 3 Replies View RelatedCisco Routers :: Setup VPN Form Outside To Use Static Address From Lan Side Of RV082?
Dec 19, 2011I have a RV082.I need to set up a VPN form outside to use a Static address from the Lan side of the RV082.
Lan is 172.16.0.126
Wan is 10.161.48.1
The computer using the VPN will need a virtual IP on the Lan of the RV082 so that it is seen as being on the same network as the equipment on the LAN.
Cisco Routers :: RV220W Doesn't Accept Address In Static IP Type
Jan 5, 2013For some strange reason I'm getting the error "WAN IP should not be a network address" when I type in an IP address under the Static IP Settings section in the "IP Address" field. My client has a static IP from his ISP and I'm trying to set it up on the router. I've updated to the latest firmware 1.0.4.17 but still the same error.
I'm not copying and pasting the address, I'm typing it in. There is no extra spaces or anything. What is this glitch? I could save the router settings and reset it and try that but I'm doing this all remotely and would rather not have to make another trip to do this onsite.
Routers / Switches :: Forgot Ip Address Used To Configure Router
Mar 29, 2011I remember long ago I was upto some trial and error with my router and I ended up in changing some ip that I didn't know about that time, now when I was trying to forward some of the ports. I addressed the computer to 192.168.1.1 (as this was my ip that time I remember and on the box its written too) but it didn't respond, then I remember that I have changed this ip to something else and now I can't remember this.
View 7 Replies View RelatedCisco Routers :: SRP527W QOS Over VPN?
Apr 17, 2013if the SRP527W supports QOS over a site to site VPN.
SITE A will have the main phone system and SITE B will have a couple of phones which hook into the SITE A phone system over the existing IPSEC VPN
Need to be able to set some type of QOS over the VPN connection.
Cisco Routers :: RV180W With 1.0.2.6 Firmware - Static DHCP Have No Buttons To Add New Static Lease
Mar 12, 2013Today I installed the 1.0.2.6 Firmware on a RV180W. I only have now two problems regarding the Static DHCP support in the GUI.
1. Via the Networking > LAN (Local Network) > Static DHCP I have no buttons to Add a new static Lease.
2. Via the Networking > LAN (Local Network) > DHCP Lease Clients I can thick a Lease and click on Make Static IP. The result is an error: Operation failed.
Cisco Routers :: Redirect Web Traffic On SRP527W
Mar 16, 2012Is it possible to redirect all web traffic to a Symantec web filtering address on a particular listening port. I had a look at the Srp527w Router and can't find where this could be done.
View 1 Replies View RelatedCisco Routers :: SRP527W VLAN Not Talking To Each Other
Dec 17, 2012I have a SRP527W router connected to a L2 managed switch (a TP-Link... I know, it is not a Cisco...). and a PC and a Printer connected to the switch. Now, I want to have the PC and the printer on 2 VLANs.
I've created 2 VLANs on the SRP (192.168.1.0/24 and 192.168.2.0/24) and I have assigned Lan port 1 to both. The SRP acts a DHCP server so I have the SRP setup as 192.168.1.1 and 192.168.2.1 providing IP addresses to the 2 VLANs.
I setup VLAN 1 and 2 on the switch, assigning port 2 to VLAN 1 and port 3 to VLAN 2 (port 1 is trunk and connects to the SRP).
When I fire up the PC and printer they get their respective VLANs correct addresses (PC: 192.168.1.30 and printer: 192.168.2.30) but I cannot for the love of Odin see the printer from the PC. The SRP has Inter VLAN routing enabled. By the way, the switch has address 192.168.1.2
Cisco Routers :: SRP527W VPN For MAC To Run IGMP Snooping
Sep 12, 2012I have a network which is based upon a 4507 Core/Dist switch, with 1G fibre to a bunch of radially connected 2960 Access switches. It all works fine and as expected for data and telephony.I have been tasked with setting up one of the VLANs to support multicast, so a bunch of video streams will be injected at the 4507, and will be delivered to client PCs connected to the 2960 switches.The 4507 is running with SVIs to some VLANs, but the VLAN that will have the Multicast on it is isolated, with no SVI.I could change this if required,I need to run IGMP snooping, and probably deploy CGMP to take advantage of the Cisco-proprietary functionaity.
View 4 Replies View RelatedCisco Routers :: Tweak SNR Margin On SRP527W-U?
Jun 5, 2012I've got a new Cisco srp527w-u router which is working fine though it's syncing at a lower rate than my Billion (6mbps vs. 8.5 mbps for the billion on the same line). I had tweaked the billion way back to connect with a 4db SNR margin and almost certainly this is why it achieves the higher rate (by comparison the cisco is syncing with an snr margin of 12db). Is there some way that I can configure it to use a lower SNR margin? I realize this might reduce connection stability but I'd at least like to be able to give it a try if possible.
View 2 Replies View RelatedCisco Routers :: SRP527W Configuring Guest Wi-Fi
Jan 28, 2012I recently bought a Cisco SRP527W and I'm trying to setup a second wireless network for guests.
I created a "guest" VLAN and I assigned the "guest" SSID which I have created.
I created a "guest" DHCP server and assigned it to the "guest" VLAN.
The "guest" SSID is set to broadcast and has WPA2 Personal (TKIP+AES) authentication. These are exactly the same settings I have for the "non-guest" WiFi.
However, I can't get my clients to connect to the network. The "guest" WiFi is visible and clients are prompted to enter the password but after that they end up with an APIPA address. When I move the "guest" SSID to VLAN1 (along with all the other networks) then it works absolutely fine.
I was just wondering if I'm simply missing something in the configuration ..
The device is running the latest firmware (1.01.24 (003) September 7, 2011)
DHCP server has DNS Proxy setting enabled and WAN Interface configured as "Default Route" (have basically replicated the same settings as VLAN1)
Cisco Routers :: SRP527W And Filemaker Server
Apr 30, 2013my client has just had the above router supplied by telstra and upon setup can no longer access filemaker server which was accessed prior on their netgear router. I have port forwarded to 5003 and 16000 as per the previous setup. Is there another setting somewhere that i am missing like perhaps static ip or something. I might add that networking is not my strong point.
View 7 Replies View RelatedCisco Routers :: SRP527W-U No Multicast Between Wired And Wi-Fi
Oct 21, 2012I've just received a new SRP527W-U-E-K9 router to replace an old D-link router. However Apple IOS devices are not discoverable by iTunes on a Windows PC. The PC is connected to SRP527 by wired ethernet. All IOS devices are on the same SSID and the same VLAN as the wired ethernet devices.I have been reading on several other threads in this site about this exact same problem. The fault was that multicast broadcasts were not being forwarded between wired ethernet and WiFi on the same vlan. url...
The fault in thie above thread was resolved by a firmware update MR3 (v1.1.19) last year however it appears that the SRP527W-U has slightly different firmware to this version.The configuration of my SRP527 is the same as the original poster's config in the above thread. [code] The version information of my SRP is embedded below. As it is brand new, I assume that it is the most recent firmware, so I would have assumed that the bug which was resolved in the above thread above would be incorporated in this firmware version. [code] Is Cisco aware of this problem and is there any other firmware that I can load onto my model of SRP to resolve this?
Cisco Routers :: SRP527W VPN Can't See Shared Drives
Sep 16, 2012I have a Cisco SRP527W at my remote office set up. I have configered a VPN connection to it. I installed Cisco VPN Client on my laptop.I can connect to the VPN but can not access the shared folders. I can ping the PC that has the shared folders. I take my PC and connect to the onsite LAN with WIFI, and I can now view the shared folders. I assume it must be somthing in the VPN set up that is blocking the shared folders from being seen. I also have disconnect all firewalls during testing at the remote end. I'am using windows 7 (64) on both PC's.
View 6 Replies View RelatedCisco Routers :: Windows 7 VPN Client For SRP527w
Jun 3, 2012I've just purchased a SRP527w router and loaded the new firmware which includes the 5 client VPN server function.
The function works great with my iPhone as a client, but I've been unable to make a connection from my Windows 7 laptop, as the built in VPN configuration doesn't have anywhere to put the group name.
Is there a VPN client, or is there some way to get the Windows 7 native VPN configuration to work?
Cisco Routers :: SRP527W SIP Source IP Registration
Nov 5, 2012We have a SRP527W, we have created VLAN for DATA and VOICE remotly connected to an office by VPN.
VPN is working fine.
Now we want to register SIP lines integrated in SRP527W to a Cisco Call Manager located in our office.
The problem is that the source of SIP packets is WAN interface of the SRP527W, so packet wont pass in the VPN. Is possible to change the IP source of the SIP registration ? The most useful will be to set the IP source SIP on the voice VLAN.
Cisco Routers :: SRP527W - Can Use For Routing Subnet Other Than NAT
Feb 12, 2012I'm wanting to use the SRP527W (from Telstra) to route a block of assigned internet addresses (/29) over the WAN internet IP address. Is this possible on the 527W, or does it only do NAT routing?
View 6 Replies View RelatedCisco Routers :: SRP527W U - Policy Route
Nov 26, 2012I have a pair of SRP527W-U units, which each connect to a separate ISP by ADSL2+ . I am attempting to use each simultaneously as follows:
ISP-A via Cisco A for general traffic, and to run HTTP server X
ISP-B via Cisco B to run HTTP server Y
HTTP servers X and Y are on one machine, but binding to two separate IP addresses eg x.x.x.3 and x.x.x.4 . In a situation like this, I would normally configure Cisco A and Cisco B with x.x.x.1 and x.x.x.2 respectively. CiscoA would run DMZ to x.x.x.3 and Cisco B DMZ to x.x.x.4. The server would use x.x.x.1 as the default route. Then I would set Cisco A to have a policy route catching source address x.x.x.4 and sending it to next-hop/gateway x.x.x.2.
BUT, the policy route feature requires traffic be sent out the WAN port or a tunnel (no next hop, only WAN side VLANs, tunnels or interfaces). configuring a GRE tunnel connecting the two routers is fruitless, and the tunnels refuse to be created on the LAN side (tunneling is only possible out the WAN).
Attempting to simultaneously use the 4th LAN/WAN port in WAN mode also fails, as the WAN port is only available when the ADSL port is not. Under Win2000 and Linux it was possible to configure two separate network cards and use seperate sub nets, each with a default route. This feature no longer works with more recent versions of Windows.
How I might get this working, without buying a 887? I am open to buying a 547.
Cisco Routers :: 867 - SRP527W Unnumbered Interface
Mar 20, 2012Currently we're using Cisco 867 routers, wich connect to a IP-VPN network with internal IP's. I'm trying to test a SRP527W router as a replacement for the current 867 routers, as they are more affordable for our customers in the SMB segment.
However all our 867 routers have 'ip unnumbered' on their dialer interfaces (we're using PPPoA) to avoid NAT and problems with SIP and easy management of the IP Phones behind the router.
Does any know if it is possible to have the same IP on the WAN interface and the LAN interface? If so, how do you configure it in the SRP527W?
Cisco Routers :: SRP527W TCP Dump Option
Apr 17, 2013I upgraded the firmware to latest and apparently i've lost couple of options inlcuding TCP Dump in diagnostic as well as I cannot find how to disable/enable an ethernet port.
View 5 Replies View RelatedCisco Routers :: Wireless Voice With SRP527w
Feb 2, 2013I have recently purchased a srp527w and I am thinking to buy a Cisco wireless ip phone 7921g. Does it works with the srp527? Do I need another device betweenn my srp527 and the ip phone? or it just works by configuring the voice vlan. If so, what phone would it work, the analog or the ip phone?
View 2 Replies View RelatedCisco Routers :: SRP527w - Using Two Incoming VLANs
Aug 20, 2011having trouble to configure the Cisco SRP527w where we have two incoming VLAN's.
1. vlan1 is for internet (20mbps)
2. vlan2 is for a specific application (Specific IP Address - 10mbps)
Somehow we are unable to configure the router to enable PC's connected to the router to access both vlan based to the application specific vlan. Its always routing it through the internet.
Cisco Routers :: SRP527W SSH Usernames / Password?
Sep 16, 2010im having trouble setting up site to site vpn from my 527w to my 877 series and thought it would be much easier to see whats going on the 527 if i could see command line
so ive ssh'd to the 527s ip address but none of the usernames/password combos work that let me in the web gui, what are the logins?