I'm tryng to configure a vpn with a cisco small business pro router, model srp527W-k9-g5 But when i try to set the “remote ip” in Remote traffic selection a I have to set (10.0.0.0) a message said:
“Invalid IP Address Format”
If i change the ip and i put 10.0.0.1 i have not error but I have to put 10.0.0.0 and if i configure it on a cisco WRV210 (por example) i have no error.
I recently bought a Cisco SRP527W and I'm trying to setup a second wireless network for guests.
I created a "guest" VLAN and I assigned the "guest" SSID which I have created.
I created a "guest" DHCP server and assigned it to the "guest" VLAN.
The "guest" SSID is set to broadcast and has WPA2 Personal (TKIP+AES) authentication. These are exactly the same settings I have for the "non-guest" WiFi.
However, I can't get my clients to connect to the network. The "guest" WiFi is visible and clients are prompted to enter the password but after that they end up with an APIPA address. When I move the "guest" SSID to VLAN1 (along with all the other networks) then it works absolutely fine.
I was just wondering if I'm simply missing something in the configuration ..
The device is running the latest firmware (1.01.24 (003) September 7, 2011)
DHCP server has DNS Proxy setting enabled and WAN Interface configured as "Default Route" (have basically replicated the same settings as VLAN1)
I need to know how to configure SRP527w without a static outside ip address to establish a VPN tunnel with VPNC3000.
View 31 Replies View RelatedI have made a test lab on packet tracer with three routers in triangle shape after each router i connected a switch with on each switch four end devices . now i want to make a routing table on each router, but the probleme is that each time i get an error "invalid next hop address ( its this router)". i am sure its the right gateway i type in .
View 3 Replies View RelatedMy PC says "invalid IP address" when I try to connect. It says the IP address is 00:00:00:00. it only does this on the computer but works fine on all our laptops. I've been googleing solutions and i have tried the 'ipconfig/release' and 'ipconfig/renew' but this doesn't work. It just comes up with a error (I think its because the computer cant connect). We use a Belkin wireless connector. Its windows xp.
View 1 Replies View Relatedwant to know how to format IPv6
View 1 Replies View RelatedMy laptop running Windows 7 has been fine until this holiday, connected to a hotel wifi that "trapped" the broswer and requested a login and password. That worked fine, but now I cannot access any other wifi networks.It sits for a while after entering the code and then has limited access, running the troubleshooter it says that I have no valid IP address?Tried IPCONFIG /RELEASE and it is saying "No operation can be performed on Local Connection 2 while it has its media disconnected"
View 8 Replies View Relatedi'm getting invalid ip address during connection to nearby wireless network
View 1 Replies View Relatedhowdy,im having trouble with my LAC.it just keeps identifying.i have tried everything,uninstall/reinstall, netsh winsock reset,netsh int ip reset,disable/enable.windows diagnostics comes back with invalid ip address,and modem hardware failure.device manager lists the network adapter as working,yet it doesn't here's my ipconfig[CODE]
View 5 Replies View RelatedI have a 7" netbook but won't connect wirelessly it comes up invalid ip address
View 2 Replies View RelatedI installed the 2.06NA on my DIR-655 router and now I'm having problems adding mac addresses to the network filter. The message is "Invalid MAC address". Of course, it doesn't tell me which entry is invalid and I have a number of them. After further checking.. I noticed that one of the MAC addresses is indeed invalid and when I remove it I still get the error message?
View 1 Replies View RelatedI am unable to reserve an IP for my iPad, i.e. add my ipad to the "DHCP RESERVATIONS LIST". I get a pop-up saying "The MAC Address entered is invalid." The address starts with "D8". My understanding is most start w/ "00". The router says my firmware is up-to-date (3.01).
View 11 Replies View RelatedI had no problem running both 2.4 and 5.0 Bandwidth. With WiFi password and without. It does it's job. The 2.4Ghz Range Plus works. I have set up the router on the 2nd floor at the highest it can go. And everyone get's full bars all over the house. I even get 4-5 bars outside in my car on my phone.
The only issue I have with this thing is a damn new netbook I got for Christmas with a Mac Address starting with 0C-EE-E6-XX-XX-XX. The Router finds the Mac Address invalid. In which I can come to understand cause seeing a Mac Address starting like that is completely new to me. Every Mac Address I have, started with 00 except the netbook. So now, I spent days trying to find firmware updates, patches, anything! I even attempted to spoof the Mac Address on the netbook but Microsoft has a bug on Windows 7. (I have the Starter Edition that came with the netbook)
Windows 7 Mac Spoofing works with WIRED Connection. But it does not work with WIRELESS Connection. I used 3rd Party Tools: SMAC and etc... I attempted Registry Edits, I changed even the value key to the "Orginal Mac Address" and it just wont change [New Strings/Network Address Edits included]. I have been banging my head about this for a week now. The Internets has many answers but they did not work. So Spoofing the Mac Address is out of the question. Until Microsoft fixes this bug.
Anyway: Did D-Link release any sort of beta update/driver/firmware or anything to resolve this at all? Is there a modded firmware to force the Router to take this stupid paradox of a Mac Address?
Currently: I have the Router's WiFi Password-ed with Default Factory Settings
{Hardware Version: B1
Firmware Version: 2.02NA}.
Issue: When I attempt to save the changes I made to the DHCP reservation list I get an error window that reads:
http:\201.201.201.201 (my internal router IP address - changed from 192.168.0.1)
Host name Invalid I have a DHCP Range setup as 201.201.201.100 to 201.201.201.199
I'm attempting to reserve an IP address of 201.201.201.199 for one of the computers on my network.
I can see the computer on the dir825 router and am connecting to it through a linksys wrtgs working as a repeater bridge running dd-wrt. The computer in question is successfully getting it's IP address from the dhcp server on the dlink router.
The dir825 is running 2.05na firmware. Why am I unable to reserve an IP address?
I have read through the manual. My question is what is the proper format to input into the ACL rule "Range"? Would as an example work- 192.168.0.1 - 192.169.255.254? Will the range effectively work? Or does it have to be 192.168.0.0 - 192.169.255.255?
View 7 Replies View RelatedOne of our Cat5513 has been displaying a lot of the error message below:
%SYS-4-P2_WARN: 8/Invalid traffic from multicast source address 01:00:5a:52:4c:4d on port 8/58
The frequency of this is quite disturbing. What this error is about? Module no.8 is our Gigabit Ethernet WS-X5410. Can that multicast address be mapped to an IP address or unicast mac-addresS? How can i go about resolving this?
I am trying to add a new computer to my wireless statione access list but have not been successful. I got the ip address of the computer i was trying to add, my issue is how to add it to the list. i tried adding the details and filling in the device name and MAC address but kept getting the error message "invalid MAC address.please enter again.
View 1 Replies View Relatedim triyng to forward a port but when i click save settings it give me a message: "Entry 10: Invalid IP Address".
View 9 Replies View Relatedif the SRP527W supports QOS over a site to site VPN.
SITE A will have the main phone system and SITE B will have a couple of phones which hook into the SITE A phone system over the existing IPSEC VPN
Need to be able to set some type of QOS over the VPN connection.
Most of the 4500 Switches in our network are giving the similar error for so many ports
%C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 1 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on p t Gi2/6 in vlan 100
Its impossible to do a wireshark packet tracing for all the ports.
Issue I am having with a Cisco 4507? Below is the error i am receiving.
Feb 14 10:06:09 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 508 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112
Feb 14 18:44:06 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 119 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112
Feb 15 00:51:06 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 366 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112
[Code]...
I bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.
View 2 Replies View RelatedIs it possible to redirect all web traffic to a Symantec web filtering address on a particular listening port. I had a look at the Srp527w Router and can't find where this could be done.
View 1 Replies View RelatedI have a SRP527W router connected to a L2 managed switch (a TP-Link... I know, it is not a Cisco...). and a PC and a Printer connected to the switch. Now, I want to have the PC and the printer on 2 VLANs.
I've created 2 VLANs on the SRP (192.168.1.0/24 and 192.168.2.0/24) and I have assigned Lan port 1 to both. The SRP acts a DHCP server so I have the SRP setup as 192.168.1.1 and 192.168.2.1 providing IP addresses to the 2 VLANs.
I setup VLAN 1 and 2 on the switch, assigning port 2 to VLAN 1 and port 3 to VLAN 2 (port 1 is trunk and connects to the SRP).
When I fire up the PC and printer they get their respective VLANs correct addresses (PC: 192.168.1.30 and printer: 192.168.2.30) but I cannot for the love of Odin see the printer from the PC. The SRP has Inter VLAN routing enabled. By the way, the switch has address 192.168.1.2
I have a network which is based upon a 4507 Core/Dist switch, with 1G fibre to a bunch of radially connected 2960 Access switches. It all works fine and as expected for data and telephony.I have been tasked with setting up one of the VLANs to support multicast, so a bunch of video streams will be injected at the 4507, and will be delivered to client PCs connected to the 2960 switches.The 4507 is running with SVIs to some VLANs, but the VLAN that will have the Multicast on it is isolated, with no SVI.I could change this if required,I need to run IGMP snooping, and probably deploy CGMP to take advantage of the Cisco-proprietary functionaity.
View 4 Replies View RelatedI've got a new Cisco srp527w-u router which is working fine though it's syncing at a lower rate than my Billion (6mbps vs. 8.5 mbps for the billion on the same line). I had tweaked the billion way back to connect with a 4db SNR margin and almost certainly this is why it achieves the higher rate (by comparison the cisco is syncing with an snr margin of 12db). Is there some way that I can configure it to use a lower SNR margin? I realize this might reduce connection stability but I'd at least like to be able to give it a try if possible.
View 2 Replies View Relatedmy client has just had the above router supplied by telstra and upon setup can no longer access filemaker server which was accessed prior on their netgear router. I have port forwarded to 5003 and 16000 as per the previous setup. Is there another setting somewhere that i am missing like perhaps static ip or something. I might add that networking is not my strong point.
View 7 Replies View RelatedI've just received a new SRP527W-U-E-K9 router to replace an old D-link router. However Apple IOS devices are not discoverable by iTunes on a Windows PC. The PC is connected to SRP527 by wired ethernet. All IOS devices are on the same SSID and the same VLAN as the wired ethernet devices.I have been reading on several other threads in this site about this exact same problem. The fault was that multicast broadcasts were not being forwarded between wired ethernet and WiFi on the same vlan. url...
The fault in thie above thread was resolved by a firmware update MR3 (v1.1.19) last year however it appears that the SRP527W-U has slightly different firmware to this version.The configuration of my SRP527 is the same as the original poster's config in the above thread. [code] The version information of my SRP is embedded below. As it is brand new, I assume that it is the most recent firmware, so I would have assumed that the bug which was resolved in the above thread above would be incorporated in this firmware version. [code] Is Cisco aware of this problem and is there any other firmware that I can load onto my model of SRP to resolve this?
I have a Cisco SRP527W at my remote office set up. I have configered a VPN connection to it. I installed Cisco VPN Client on my laptop.I can connect to the VPN but can not access the shared folders. I can ping the PC that has the shared folders. I take my PC and connect to the onsite LAN with WIFI, and I can now view the shared folders. I assume it must be somthing in the VPN set up that is blocking the shared folders from being seen. I also have disconnect all firewalls during testing at the remote end. I'am using windows 7 (64) on both PC's.
View 6 Replies View RelatedI've just purchased a SRP527w router and loaded the new firmware which includes the 5 client VPN server function.
The function works great with my iPhone as a client, but I've been unable to make a connection from my Windows 7 laptop, as the built in VPN configuration doesn't have anywhere to put the group name.
Is there a VPN client, or is there some way to get the Windows 7 native VPN configuration to work?
We have a SRP527W, we have created VLAN for DATA and VOICE remotly connected to an office by VPN.
VPN is working fine.
Now we want to register SIP lines integrated in SRP527W to a Cisco Call Manager located in our office.
The problem is that the source of SIP packets is WAN interface of the SRP527W, so packet wont pass in the VPN. Is possible to change the IP source of the SIP registration ? The most useful will be to set the IP source SIP on the voice VLAN.
I'm wanting to use the SRP527W (from Telstra) to route a block of assigned internet addresses (/29) over the WAN internet IP address. Is this possible on the 527W, or does it only do NAT routing?
View 6 Replies View RelatedI have a pair of SRP527W-U units, which each connect to a separate ISP by ADSL2+ . I am attempting to use each simultaneously as follows:
ISP-A via Cisco A for general traffic, and to run HTTP server X
ISP-B via Cisco B to run HTTP server Y
HTTP servers X and Y are on one machine, but binding to two separate IP addresses eg x.x.x.3 and x.x.x.4 . In a situation like this, I would normally configure Cisco A and Cisco B with x.x.x.1 and x.x.x.2 respectively. CiscoA would run DMZ to x.x.x.3 and Cisco B DMZ to x.x.x.4. The server would use x.x.x.1 as the default route. Then I would set Cisco A to have a policy route catching source address x.x.x.4 and sending it to next-hop/gateway x.x.x.2.
BUT, the policy route feature requires traffic be sent out the WAN port or a tunnel (no next hop, only WAN side VLANs, tunnels or interfaces). configuring a GRE tunnel connecting the two routers is fruitless, and the tunnels refuse to be created on the LAN side (tunneling is only possible out the WAN).
Attempting to simultaneously use the 4th LAN/WAN port in WAN mode also fails, as the WAN port is only available when the ADSL port is not. Under Win2000 and Linux it was possible to configure two separate network cards and use seperate sub nets, each with a default route. This feature no longer works with more recent versions of Windows.
How I might get this working, without buying a 887? I am open to buying a 547.
