I have what I feel is sort of a strange issue. When I have systems on my home network get their IP from DHCP, they can get to the internet just fine. But it seems that when I assign a static address, they have local network access only, and will not get a connection to the internet. My windows 2008 server is the big problem with this one.
View 10 RepliesI"m having one problem though. On my old router it had a feature to assign a static IP to a mac address.
So that computer would always get 192.168.10.101 as the IP Address.
How do I do it on this router?
I am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
Actually I have a lab with ACS 5.3 running with 802.1x, but when when the user is successfully authenticated, it's assigned and IP address from the DHCP server, is there a way to assign a static IP address depending of login username??
View 13 Replies View RelatedI had no trouble getting connected to the internet a couple of months ago. Then the signal got weak. I have a better antenna now and the network shows 5 bars but I cannot connect. It is an open, unencrypted connection. Wi-Fi Inspector gives this info[CODE]
View 19 Replies View RelatedIs it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies View RelatedMy system is in LAN. IP is assigned by DHCP. Now i want to assign a STATIC IP to my system. There is no direct connection from vendor router to my PC. My network path is like this. From ISP vendor to Switch->Firewall-> LAN switch. how can i configure Static IP in my PC..
View 4 Replies View RelatedOk so I have a couple devices connected to it, but there's a trick with Android phones that users report better battery life assigning an Static IP to the phone, not dhcp or reservation. However I can't figure it out in this router as when I revoked the current address it wouldn't let me add a new one, and when I went to add one at .202 to be outside of dhcp range it doesn't let you and says to enter a number within the range, .100-.199
View 6 Replies View RelatedI've been given 4 more public static ip's and would like to use one of them static ip's to point to my sharepoint box, for example i want to be able to access my sharepoint boxweb site externally:
212.xxx.xxx.01 - my public pix ip
212.xxx.xxx.02 - is my owa for email (https://xxxxxxx.net/owa)
212.xxx.xxx.03 - my sharepoint box (https://xxxxxx.net/sharepoint)
212.xxx.xxx.04 - not assigned
What command do I have to input on the Cisco Pix 515 to make that work?
i have a ISDN connection i have got 1 static WAN ip and 7 static LAN ip . i have connected it to a server 2008 r2 given that the WAN ip and shared it how do i assisgn 7 LAN static IP in local area network
View 3 Replies View RelatedI have a WAG 120N Modem Router, My question is: Can you assign an static IP to a pc using this router?
View 2 Replies View Relatedwith my broadband internet I received a range of 5 IP addresses from BT. I would like to assign one of them to the modem, in order to reach the modem from the outside using that IP.,Is this theoretically possible at all?,Is the WAG320N supporting static IP addresses with PPPoA at all?,When I select PPPoA as the encapsulation on the Setup/Basic setup tab, I cannot enter an IP address on that tab. I tried using the Setup/Ethernet tab, but selecting ""Use as a WAN port", "Static IP", inserting the IP and clicking on "save" result in a cut of the internet connection.
View 3 Replies View RelatedI want to assign static IPs to users that login to IPSec VPN using Group Authentication in ASA 8.2. The authentication through a Windows RADIUS server. Right now, they are connecting just fine and pulling an IP from the pool I have configured in the IPSec policy.
What would the best way to assign static IPs through VPN?
I have assigned a Static IP with other Linksys/Cisco wireless routers (WRT54G), but I can't seem to get the E4200 to assign a Static IP. My device is connected to Port 3, with that being the only port (besides my WAN) being occupied. When I enter the following and click Save Settings I get the following error: "Invalid Static Route!"I don't understand what I am doing wrong. This is the exact same as I have done on my WRT54G and it worked.
View 2 Replies View RelatedMy printer (HP7210) is wired connected to my WRT54GL router. 2 computers have also a wired connection, my laptop is connected wireless. All these computers use the connected printer. 2 computers can only use a static IP-address for the printer. How can I set a static IP address in my router?
View 3 Replies View RelatedWhen I was hosting a server on minecraft, a few people complained that the server was down. It was, and the problem is that my router switched to a dynamic IP after comcast installed a security system to my house. If I try to reset the router, the system goes down and takes a helluva long time to get back up. Whenever I try to switch to a static IP, however, I lose internet connection. Wondering how to fix this. Or do I have to switch back to my laptop - which might also not even work. (I'll go try that, but I'm using my desktop because it has extra RAM.)
View 19 Replies View Relateddo internet cafes use static ip or dynamic ip address. Also what would be the benefit if they used a static ip address.
View 1 Replies View RelatedWe have a Highly available VPN infrastructure across two data centers. We also use ACS 4.2 servers for authentication. The ACS servers are in teh same "cluster" in a Primary and Secondary fashion. Site A has primary ACS and primary ASA 5550 IPSec VPN termination. Site B has secondary ACS and redundant ASA 5550 IPsec VPN termination. We also use InfoBlox for DHCP IP address assignments. The two IPSec VPN Head end devices, ASA 5550s, they use different subnets for IP pools for the VPN Clients. Site A uses x.x.24.0 and Site B uses x.y.24.0. As indicated VPN clients authenticate using teh ACS 4.2 Radiius server. I can assign static IPs per user on the ACS server but this can only work for the primary site. Once static IP address is assigned on primary ACS for a user, this status will be replicated to the secondary ACS on Site B. When the Primary IPSec VPN Head End ASA or Internet fails on Site A, Clients on DHCP will work fine seemlessly via Site B. But for the static IP users, you have to change the Assigned Static IPs to match the subnet on Site B. How I can assign static IPs to clients via both Sites without manual intervention. Either via DHCP or ASA. I was trying to stay away from creating multiple Groups for VPN and also avoidng creating local ASA users because these options will not scale well as static user base increases. I need users to get a static IP address from Site A subnet when connected to Site A and get a static from Site B subnet when connected through Site B.
View 1 Replies View RelatedI am having a cisco 861 series router.The Cable from the isp was connected to fastethernet4(wan port)
Following are my isp details
IP address:172.16.62.130
subnet:255.255.0.0
default gate way:172.16.62.1
dns primary:202.153.32.2
secondary:202.153.32.3
How do i configure this details in the router and access the internet in my devices.
i want the network to be in 192.168.1.0 to 254.
how do i configure my router with this details using cisco configuration professional
I upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.
ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit
ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46
default-router 10.10.14.1exit
I have a 2003 server that is doing something wrong. When I show the mac address table I can see that the server is assigning a bad mac address to several IPS. The server assign a non-existent mac address to some IPS for this reason the server stobut I would like to solve the problem
- I ran my antivirus an no virus was found.
- I updated the network driver.
I have a Compaq Presario 6000. The DHCP server is not getting a valid IP address. How do I troubleshoot?
View 2 Replies View RelatedHow to assign ip address in xp
View 2 Replies View RelatedI was using an IP address at one of client side and i got an IP address conflicted error and i changed the ip, Hence when i am searching that where does it consume on other systems i don't get the location & i need to use the conflicted one IP address so how can i know that which system does it using, i manually checked all systems i did not get, the ip address is gets ping but unable to get its location.
View 2 Replies View RelatedI know DHCP can assign more than just address, mask, and gateway. It can also assign a hostname, and DNS. Does anybody know if it can also be used to assign an SNMP address?
View 6 Replies View RelatedI understand you can't assign an IPv4 Address to a "port". But here's my issue. I have two network cables attached to a managed switch, the location of the two cables are very important. Two computers attached to the said cables.I would like to communicate with one of the computers on PORT 1 and PORT 2, regardless of what computer is plugged into them. They get there IP's via DHCP, and a static IP wont work - as the computer plugged into PORT 1 or 2 may be different.So. I have two ports on the switch that I always want to communicate with the computer on the other end. But I don't (will not) always know the IP address of the computer(s) connected.
View 12 Replies View RelatedI know that a default gateway is used to log in remotely, but what is the purpose of the IP address on a VLAN?
View 3 Replies View RelatedI have a public IP and I want to be able to view my three systems connected to a linksys router from the internet. How can configure the router to see three systems with just one Public IP address whenever I am on the internet?
View 5 Replies View RelatedI'm using CCP to configure my Cisco 881, I need to assign my IP address range to the WAN interface (176.35.224.112/29), however everytime i enter the IP Address with a /29 subnet mask or indeed one of the usable addresses with a /32 I'm told I need to "Enter a valid IP address".I have also attempted to set the interfaces IP address via IOS directly and was also told the address was incorrect.
View 1 Replies View RelatedThere are 6 computers in our home network. It happens every few months or so that router would not assign valid IP address to one of the computers. So, most of the time everything works well, but there comes a moment when one of the computers (but not others) can't get valid IP address.We try turning off and then on the router and it solves the problem most of the time. But, there are cases when turning off and on the router won't solve the problem.
View 3 Replies View RelatedI am trying to assign a static IP address for network adaptor as i am going to be using it to install Active Directory on VMWare Worksation. I was told that if i went into Device Manager within my worksation then Advance > Locall Administered Address and set a static IP, when i install AD and it asks to whether set a static or dynamic IP it would continue the install process. However, after setting a static ip it did not, can somebody tell me how i can set the correct IP address for me to continue instaling AD.
View 12 Replies View RelatedI have an HP 510 laptop running windows xp. Wherever i go, i am able to connect through wifi with a password except for where i live. I have had no problems connecting anywhere else. All other laptops and pc's connect through the network i cant access. I get a 'limited or no connectivity' message with details displaying either 'network did not assign a network address to the computer', 'cannot connect to the internet' or 'cannot renew ip address. I reviewed a few older posts and have tried ipconfig/release, ipconfig/renew, ipconfig/all to no avail. i also tried netsh ip reset reset.log and netsh windows catalog(or something along those lines) from the earlier post i read, still nothing. I do notice that when i go to properties the wep password always reverts to one i did not enter, and once in a great while when i re-enter it the icon will show 'connected to network, excellent signal strength' but Internet Explorer says not able to connect. I cant seem to figure out why i connect fine everywhere else, and why every other 'guest' computer connects to this network.
i connect using Intel(R) PRO/wireless 2200BG under properties>general under properties>wireless networks>association use windows to config is checked under properties>network>properties the network authentication is 'open' and data encryption is set to 'wep' while the network key reverts to something i did not enter. key provided is not checked under properties>wireless networks>authentication 'enable ieee 802.1x authentication for this network is not checked
I've been using the Dir-655 for 2 or 3 years with my old Xbox 360 and an external G wireless adapter. Everything was working perfectly until I got the dreaded Red Rings Of Death the other day. I replaced the Xbox with a new Slim version with built in N capable network adapter.
After more than 10 hours of trying a variety of "fixes" I found from MS and in this forum, I am still at square 1.
Hardware Version : A3
Firmware Version : 1.32NA (this is listed as Live compatible by Microsoft)
802.11 Mode : Tried N only, G only and mixed 802.11n and 802.11g
Enable Auto Channel Scan : Checked
Transmission Rate : Best (automatic)
Channel Width : Auto 20/40
Visibility Status : Visible
Security Mode : WPA-Personal Also tried WEP
WPA Mode : Auto (WPA or WPA2) Also tried WEP
Cipher Type : TKOP and AES
I tried assigning an IP manually from the Xbox. But, no matter what I do, the router will not accept it. It is especially frustrating that the Xbox is visible to the unit. It simply will not assign an IP to it under any circumstance.
If you read the sales hype promoting the Dir-655, you will see a lot of nonsense about it being great for gaming. Given that, you'd think a simple solution would have been found and posted for this issue by now. Surely, end users shouldn't be trying 100 different possible "fixes", none of which work, at this late stage of the firmware upgrades. If I sound a tad fed up, it's because I am. After the expense of the new Xbox, it appears I now have to junk my router too.
Here is the status screen taken when it was in mixed mode. Changing it to 'G Only' didn't make any difference: