configure my cisco 892 router want a static ip address assigned to the interface because and I have no more internet on the router because am working on my network academy for CCENT?
View 28 RepliesI have an 8.3(2) ASA with a single outside IP. Dynamic PAT translates inside addresses to the outside interface address. I would like to use static NAT with port translation to access an inside syslog server. I got an error when I tried using the outside interface address. Can I use both dynamic PAT and Port Translation with the same outside address?This is what I would like to use but I receive an error saying there is an overlap using the outside interface address.(192.168.1.0 is my inside network. 10.10.1.10 is the outside interface IP.)
object network inside-net
subnet 192.168.1.0 255.255.255.0
nat (inside, outside) dynamic interface
object network SYSLOG_SERVER
host 192.168.1.50
nat (inside,outside) static 10.10.1.10 service tcp ssh ssh
I am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
customer has a server which located in inside interace. and an outside interface connected to ISPA. cu config a static nat map inside server address to ISPA address, one day customer install a new outside interface to ISPB, cu config new static nat ,map same server inside server address to ISPB address. the server will allways be vistited from outside interface and reply, custome want traffic coming from ISPA will return to ISPA, traffic coming from ISPB will return to ISPB. but i found it is difficult implement this on ASA5580. i want use route-map on static nat, but it will not satisfy customer's request.
View 3 Replies View Relatedi have a problem customer has a server which located in inside interace. and an outside interface connected to ISPA. cu config a static nat map inside server address to ISPA address one day customer install a new outside interface to ISPB, cu config new static nat ,map same server inside server address to ISPB address. the server will allways be vistited from outside interface and reply, custome want traffic coming from ISPA will return to ISPA, traffic coming from ISPB will return to ISPB. but i found it is difficult implement this on ASA5580. i want use route-map on static nat, but it will not satisfy customer's request.
View 6 Replies View RelatedI have a couple a questions answers on which i cant google for a period. BTW maybe i simly use wrong aproach to choose keywords.
1) Is it possible to assign same ip address to the same client each time it authenticated, preferably without using DHCP? Im definely sure that it possible but cant find corresponded configuration examples (my device is Cisco 1921 with IOS 15.0.1).
2) Is it possible to assign dynamic crypto map to loopback interface (the purpose to make EASY VPN Server accessible through two interfaces - maybe you recommend other approach instead?) - as i move workingcrypto map from phy int to loopback - i cant connect with reason "Phace1 SA policy proposal not accepted"
I�ve assigned the static IP to Server, but when i go back to network properties it show Obtain IP address automatically, however, network working fine with previously assigned IP.
View 2 Replies View RelatedI recently switched routers to the DIR-615 and I'm trying to troubleshoot why one of our laptops keeps losing the IP address and gets a self-assigned IP address. I see the following messages in the log, I am wondering if the reason codes are listed and explained somewhere? I tried searching the manual but could not find any information.
View 9 Replies View RelatedI want to do with my ea4500 is assign it a static IP and access it after doing so. But, no matter how many times I try, I cannot enter its IP address in the address bar and see its settings. I change its IP to192 168 1 200. Subset 255... DG 192 168 1 1 DNS same.Under router address 192 168 0 1I CANNOT access this router at 192 168 0 1 at all. The thing is, the **bleep** settings are not any different the. How they were when it was WORKING. I literally took a screenshot of my setting in case a scenario like this would come up, yet it more problems arise. The only way I can access the router is by doing a factory reset and accessing it at 192 168 1 1.
View 9 Replies View RelatedI'm new to working with the ASA 5505 ,VPN and reverse NAT.
The basic setup is as follows. I'm trying to setup a IPsec site to site tunnel with reverse nat on the remote side.
I have as the tunnel up and it passes traffic. I have setup reverse NAT for 172.x.x.1 to translated IP 216.x.2.101 my ASA also has an IP address of 216.x.2.102.
Any connection from 172.x.x.1 to 216.x.2.1 should appear to be comming from 216.x.2.101
When I ping or telnet from 216.116.86.1 to an open port on 216.x.2.101 I get the banner from 172.x.x.1, seems like it is working.
However in my setup I'm only given a singel IP that of the NAT address 216.x.2.101, so when I remove the IP address assigned to the inside interface 216.x.2.102. all conductivity is lost.
When I set the inside interface to 216.x.2.101 and I setup a static NAT rule for 172.x.x.1 to 216.x.2.101, I get a message that says all traffic will be redirected and I will be unable to connect to the ASA.
Once thats in place, and I make any connection from 216.x.2.1 to 216.x.2.101on any port I get a connection but then it's reset, I no longer get the telent banner I was expecting.
My running config is,
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
I've been using this setting for clients in small offices and what not, and since all they wanted was to give another nutch of security to their network, we've been intalling cisco routers 2600 series still outhere for their internet connections and we had no issues what so ever, not until we run into cable isp provider, and their dhcp wont be able to assign our interface a dynamic IP, this is the setting aplied to the router interface;
interface fastethernet0/0
ip address dhcp
ip nat outside
no ip redirects
no ip unreachables
no ip proxy-arp
Why it wont be seen or assigned an ip by their dhcp, I talked to their isp and they assigned a static ip (private one) and we still have the same issue, if i connect a pix 506e interface with the ip add dhcp assigned to it gets a dynamic ip right away...
I have a problem with my AIR-AP1041N-E-K9, i do not seem to get an ip-address assigned after a reset to factory defaults.I do see the AP with CDP:
Device-ID: ap
Advertisement version: 2
Platform: cisco AIR-AP1041N-E-K9
Capabilities: TransBridge IGMP
Interface: gi5, Port ID (outgoing port): GigabitEthernet0
Holdtime: 163
Version: Cisco IOS Software, C1040 Software (C1140-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
[code]...
I also noticed that when i connect to the AP via console-cable, i can see the AP boot up in the console session, but then i do not get a login prompt, but it seems like the AP is responding; if i shutdown the interconnecting link between the switch and the AP, i do see log messages appearing in the console-connection.I have tried to debug on the Switch, but i need a password, so i can debug, which i do not have.,
I have 2 servers. 1 is a terminal server windows 2003 sb terminal server.(working fine) and the other is server 2003 small business DC configured with dhcp, dns, SQL, & wins. Last week one of the network programs that is located on the DC started refusing connections.So doing some trouble shooting I noticed that when I ping the server name I get a local address of *.*.*.42 when the address the machine is assigned is *.*.*.5. When I do an Ipconfig /all on the DC it only shows the *.*.*.5 number. I look in DHCP and *.*.*.5 is reserved for the DC Computer. And the *.*.*.42 isn't even in the address leases. I have also looked through the DNS settings and see no alias with the .42 number. And the number does not show up in the reverse lookup zone either.
View 5 Replies View RelatedI have set up DHCP reservations to assigned IP addresses based on MAC address. I have to block my kids access at times, and when I do this they simply change their IP address and they circumvent the blocking.Other than punishing the kids (which hasn't worked - and they need computers and Internet for homework), is there anyway to lock a computer to MAC address to IP address so if they change it they won't get network/internet access?I also tried to set up network filtering and I put in all the PCs and devices I wanted to provide access for, including the router, but when I save changes I can no longer access the internet or the router. I have to do factory reset to get back into router config.Also, I'm on 1.30WW. I know 1.34 exists, which I tried on a previous router which died and was replaced by RMA; but this didn't solve any problems.
View 6 Replies View RelatedIs there any way to get an ip address through it's physical location? I was asked this by a friend and it's a good question. We know how to get the physical address by it's by coordinates, but is it possible to reverse it, getting the ip assigned to the physical address?
View 3 Replies View RelatedI just rebuilt my network and I've encountered a problem with my wireless access. Right now I have a Dlink 2540B modem/wired router.To that is connected an 8-port Dlink 2208 Switch and a Linksys WRT110 wireless router. All the desktops connect via ethernet to the switch and everything is working fine. I just added the WRT110 and specified it would be a secondary router on the network but as soon as I got it connected it killed my internet. I assumed this was because of DHCP being enabled, which was true once I logged in and looked. I of course disabled it and now the internet is back up on the wired portion and I can connect to the wireless router as well. But the only problem now is that my wireless devices are not being assigned IP's at all. Specifically, my Mac says "airport has a self assigned ip address and will not be able to connect to the internet"How are IP's assigned to wireless devices that connect to the network via a wireless router with DHCP disabled?
View 1 Replies View RelatedWe recently implement WLC 5500 Series, I found out guest user once period of that user expired it will not appear at lobbyadmin page where you can see list of users.
Is there any way to see expired guest users and also IP address which assign to guest user?
I've configured vpn ipsec with wizard but my ip address assigned by pool not reach the lan network ,lan network: 192.168.0.0 /24,pool network: 193.168.0.0 /24
View 12 Replies View RelatedHow can I change my external IP address which is assigned
View 1 Replies View RelatedI am trying to setup VLANs and most of configurations are working ok now except IP address assignment from DHCP. If any computer in VLAN 120 or 130 configured with manual IP address, then all works fine. It can reach internal servers and the internet without problem.If the IP address is assigned automatically then any computer in VLAN 120 or 130 are obtaining IP address (strangely!) from VLAN 100. Because switch ports that connected to the computer belongs to VLAN 120 or 130, the computer cannot reach internal servers and the internet with ip address from VLAN 100 . All SVI interfaces for VLAN 100, 120 and 130 have ip helper-address option defined pointing to the DHCP server. No DHCP snooping enabled on all switches at this point. DHCP server have three scopes for the three different VLANs.
View 2 Replies View RelatedWe have a Cisco Aironet 1242 AG Series which we are trying to setup. The DHCP assigns the IP address, but we cannot connect to it. We have had this problem with a previous Aironet unit, which this new one we have got now is also having the same problem!Everything seems to be correct, but we cannot get to the IP address to set it up.
View 12 Replies View RelatedI have a Dell Inspiron 530s desktop running Vista SP2. When I attempt to get online using a cable or a wireless USB adapter I get a self-assigned IP Address. When I manually add an IP and DNS addresses I can't get online also. I have removed my security software (webroot) and have disabled Windows Firewall.The same ethernet connection works on another one of my computers fine.
View 14 Replies View RelatedDoes having the following configuration on an ios device present any possibility that an egress stream PAT'ed to loopback gets source port translated to the statically nat'ed port? [code]
For example, egress private ip address getting pat'ed to the loopback, eventually will have its source port translated to the '7062' in this case. How does the IOS route the return packet vs a new stream hitting the y.y.y.y on the same port?
I need urgent support on creating SSID as layer 2.We have cisco WLC2504 and 1602i access point. In our network we have in gate for guest.I want to create one ssid and bind with vlan only. We can not creat interface on WLC b/c of static IP.
View 3 Replies View RelatedI have a DIR-615 rev C with firmware 3.10 and am trying to setup static routing. There is no option to select LAN for the interface
View 7 Replies View RelatedI have inherited an ASA 5520. In doing some auditing of the setup, I have noticed a Static Route that has the inside interface of the ASA as the Gateway IP. I am trying to understand the purpose of this route or why a route would be setup this way.
Example Static Route:
Inside 10.xx.31.0 255.255.255.0 10.xx.xx.10 (10.xx.xx.10 is the inside interface of ASA)
I'm receiving an error when trying to access a web server behind from one subinterface to another subinterface on an ASA access the public IP. I'm getting the following:
Global Static NAT Deny IP spoof from (61.X.X.X) to 201.X.X.X on interface Outside
Traffic dies at the firewall stating that the traffic is spoofed from the Global address (61.) to the static (201.) address. Both bound to the outside interface. When I create a static NAT on the firewall there is no problem; however when I'm patting against the firewall to the public IP I get the denies.
Is it possible to assign a static route to an interface and not globally on a ASA 5510 ver 8.3.
I have two links between my offices one for Data via a VPN and one for video traffic which is a secure connection with QOS end to end.
All interfaces are on the same security level of 100 except Outside which is 0.
Office 1 Interfaces ASA 5510
VLAN 1 vOffice1Data 10.40.1.0/24
VLAN 3 vOffice1Video 10.40.2.0/24
VLAN 5 vInterOffice 10.40.5.0/24 (QOS connection Between Offices)
[Code]....
At the moment if I try and access data from VLAN 1 to VLAN 4 it gets to the destination ok going through the static route and over the vInterOffice connection but the problem is VLAN 4 returning the traffic. This fails because there is no static route back to VLAN 1. If I create a static route from Office 2 to VLAN 1 then it will route all my data traffic over it as well.
Right now I have a lab setup with a couple of these AP's.They are both doing DHCP to get their IP address from a 5508.How do I set a static IP address on the AP?
View 5 Replies View RelatedWe have several pairs of ASA5510s in failover A/P mode, some running 8.3(2) and others running 8.4(1).
e0/0 = outside
e0/1 = inside
m0/0 = management
The problem we're having is we can't get anything to route out of the management interface unless we put in a static route at least to the subnet level. For example, we want syslog traffic to exit out m0/0 to our syslog server 10.71.211.79. Our 'gateway of last resort' points to the next hop out e0/0, and a second static route with a higher metric and a more distinct network space is for m0/0 as in:
route outside 0.0.0.0 0.0.0.0 192.168.49.129 1route management 10.72.0.0 255.255.0.0 10.72.232.94 10
This doesn't work, and ASDM loggin gives this error: ".....Routing failed to locate next hop for udp from NP Identity Ifc:10.72.232.89/514 to management:10.72.211.79/514"
If I put in a more granular subnet route, or a host route of the syslog server it works, such as:
route management 10.72.211.0 255.255.255.0 10.72.232.94 10 <------------- this works
route management 10.72.211.79 255.255.255.255 10.72.232.94 10 <------------- this works too
Why won't a static route for 10.71.0.0 255.255.0.0 work in this case?
We are going to have numerous hosts access and be sent messages though the management interface of these ASAs, and it would be very burdonsome to have to add a host, or even a subnet, route for every one. I've removed all static routes and tried to rely on EIGRP, but that doesn't work. I also had to put 'passive-interface management' under the EIGRP for this to work.
Here is the pertinant ASA config concerning syslog, routing, and interfaces:
interface Ethernet0/0 nameif outside security-level 0 ip address 192.168.49.140 255.255.255.128 standby 192.168.49.141 !interface Ethernet0/1 nameif inside security-level 100 ip address xxx.xxx.xxx.xxx 255.255.255.128 standby
[Code].....
I am trying to give an static ip address to a time clock on my network and for some reason when I connect time clock to network it will always get an ip address from a different network. for example my computer IP address is 192.168.2.70 when connected to network, my default gateway is 192.168.2.1, the IP address that the time clock always gets is 192.168.1.120, there is no way to tell the time clock what IP address I wanted to be it has to get it from router (that is what the manufacturer told me), router (16portLiksys) does not have DHCP enabled the guy who set up network left it disabled, on his notes he says server (dell server T110) is acting as router is that true that a server can be acting as router?what do guys think is going on here?all the computers hooked up to network have static IP address.I also notice that when I connect a computer to router it will get an IP address from different network the same as time clock.I tried to reserve ip address on router by entering MAC address from time clock but it won't work. I am not very familiar with the server settings I have not try changing settings on server, I am not even sure the guy who set up network is right about using server as router.
View 1 Replies View RelatedI have two different locations, two different ISP�s .
Cable �Modem--------Linksys Router WRT54G
DSL-Modem----------Linksys Router WRT54GS
One computer (Windows 7 Laptop) which travels between both locations.Can I or how do I setup a static IP address for both locations on my computer and not have to change settings when I change locations?
I am trying to configure ASA to assign same static ip address to certain user(User1) every time when he connect to network via AnyConnect client. We have Windows AD and use LDAP AAA server for authentication of VPN Remote Access users. I found in document "Cisco ASA 5500 Series Configuration Guide using the CLI, 8.2" in section "Configuring an External Server for Security Appliance User Authorization" explanation and configured ASA and User Properties in AD on exectly same way:First, I assigned static ip address in properties menu(dial in section) of User1 in Active Directory. Then I created ldap attribute map where I mapped msRADIUSFrameIPAddressattribute to IETF-Radius-Framed-IP-Address attribute. At the end I applied this ldap attribute map to AAA server group LDAP.
Although I set this up, whenever I connect using User1 credentials from AD I still get ip address from vpn pool instead static ip address that I configured. In output of debug ldap 255 command I found line "msRADIUSFramedIPAddress: value = -1062718956" but not any line that prove mapping above mentioned attributes.It seems like mapping is not working.All AnyConnect users get parameters from defined internal group policy on ASA,including addresses form pool,dns server etc. I want that User1 get static ip address and inherit all other parameters from group policy.