Cisco Switching/Routing :: AP1141 WAP IP Address Config / Routing
Dec 28, 2011
This is my first time trying to configure a WAP for out network. I have an AP1141 connecting to an SG300-28 switch. The subnet for my WAPs is 10.10. 40.0/ 24. The rest of my internal network is 10.10.10.0/24. There are four other WAPs on the 10.10.40.0/24 network that I did not configure. When I assign an IP address - 10.10.40.7 to my WAP with the gateway as 10.10.40.100 (router), I cannot ping anything. If I assign the WAP an IP address - 10.10.10.192 with the gateway 10.10.10.100 (router), I can ping everything.
View 6 Replies
ADVERTISEMENT
Dec 14, 2011
Cisco Small Business Switch POE ESW-520-24P with a Wireless Access Point Cisco Aironet AP1141. Both the devices are upgraded to the latest firmware.
Connected to the ESW-520-24P is a Windows 2008 SBS 2011 with DCHP and Domain Controller. Along with the server I have a number of wired computers connected to the switch which do not have any issues and connect to the DHCP server without any problems.
When connecting two wireless devices to the AP1141, they get the IP address and DHCP from the server; but when connecting other devices apart the first two they will fail to connect to the DHCP server and do not get any IP Address. They manage to connect to the Wireless access point but they cannot contact the DHCP server.
View 17 Replies
View Related
Apr 17, 2012
If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies
View Related
Jul 31, 2012
I have a new 6513 with 2 sup32's with IOS. This chassis will replace a working 6513 with 2 sup2's with CatOS.I need to pull the running config from the CatOS chassis and make it work on the IOS chassis. i can do this manually but was wondering if there are any trade secrets on doing this.
View 3 Replies
View Related
Jul 22, 2012
I'm in the process of configuring QOS on a 3560 routing switch in a GOLD, SILVER, BRONZE priority type scenario.
Firstly, I understand that this config will add a tag of "precedence 5" to a packet if it matches the "ACL_QOS_GOLD_In" access list. Question is does the router see this "precedence 5" tag and then sets the priority, or am I missing something in my config where at present it just sees the "precedence 5" and doesn’t act on it ?
Secondly, Since the "precedence 5" tag has already been added to the packets, do downstream routers see this tag and act accordingly or so I need to configure those is well ? [code]
View 2 Replies
View Related
Jun 5, 2012
Need to confirm on 4507 R switch should i set config reg to 0x2102 or 0x2101?
View 4 Replies
View Related
Mar 15, 2012
I have been given 2 3750 switches and need to put a config onto it wuld is for 2 3750's in a stack, how should I put this on the 2 switches? Is it bested to install it onto 1 switch first then physically attach the 2nd after?
View 3 Replies
View Related
Aug 22, 2012
I have a 1941 integrated services router that will not keep the configs. After several atempts of saving running config to the startup config, then rebooting the device. I am having to reload the configs manually from TFTP because they are gone. I have also tryed the "wr" command to see. Is there a proper way to shutdown this particular type of router?
View 2 Replies
View Related
Oct 28, 2012
I don't have access to my config at the moment and I haven't had a chance to get to the console of this router as of yet.A little background info:This is a Cisco 1941 router in which I have multiple NAT inside interfaces for internal VLANs. Before my current problem I was using one NAT outside interface for Internet access with another NAT outside connecting to our corporate network that was in a shutdown state.The router is performing router on a stick and had layer 3 subinterfaces for each VLAN. I have ACLs filtering on each subinterfaces allowing only the traffic I need through.I also currently only have one static NAT port for an FTP server.The time finally came when I had to connect our corporate network to this router via an access port on a 2950 which trunks to the router.The problem comes when I send any traffic to the subinterfaces on the corporate network which is the second NAT outside interface on the router. The main point for this connection is to do a static NAT from this interface to a web server on another VLAN. Any traffic to this interface including just pinging from the outside causes connection to the router to fail for about 3-4 min.Like I said I haven't ha the chance to get to the console yet Sony cant tell everything that happens. Nothing shows up in the logs after I can get connection back and the router didn't reboot as a "show version" says the router has been up for a long time.The CPU is also usually very low as not that much traffic flows through this router at a time.I built a very similar network in packet tracer and it works just fine.
View 1 Replies
View Related
Feb 9, 2012
We need to connect several DSLAMs on the 4900 switch, every DSLAM has 4 VLANs configured (VOIP service, MGMT, ADSL Private, ADSL Public), and sends the traffic for each service tagged with appropriate VLAN id according to the table:
VOIP: 608
MGMT: 594
ADSL PRIVATE: 2900
ADSL PUBLIC: 2930
On the DSLAM side it is very simple configuration, just a normal trunk with 4 VLANs transversing the link. On the 4900 I need to isolate the traffic for ADSL PRIVATE & PUBLIC service so DSLAMs connected to the same switch do not have L2 connectivity between them. For VOIP and MGMT they must communicate with each other. DSLAM acts also as a VOIP GW so it must communicate with other DSLAMs for VOIP service. Also VLAN 200 is configured on ME 4900 for switch management traffic.
This 4900 Switch connects to MPLS PE router, which offers L3 VPN service for VOIP & MGMT service, and L2 VPN for ADSL service (PPPoE traffic to BRAS). Fortunately we have ES+ linecard to support many ethernet features. I tried this config:
1) VOIP, DSLAM-MGMT, MPLS-MGMT configured as normal VLANs
2) ADSL PUBLIC & PRIVATE configured as isolated secondary VLANs, primary VLAN for ADSL PRIVATE is 2008, for PUBLIC 2308
3) Configure DSLAM facing ports on ME 4900 as private-vlan trunks
4) Configure ME 4900 uplink port to MPLS PE as a private-vlan promiscous trunk
5) Configure ethernet services on MPLS PE for each tag that comes from ME 4900 (ES+ cards are awesome, i love them:D )
6) Apply L3 VPN service for VOIP and DSLAM-MGMT, and L2 VPN for ADSL service.
But at least this last command should list on spanning tree forwarding state also the ADSL VLANs or not?
Here is the output of the show interface switchport.
View 1 Replies
View Related
Dec 21, 2011
I need to backup my ASA 5505 configuration and restore it to default, then I'll configure manually the new config, but if something doesn't work I want to restore the backup made before.
I tried the "copy run tftp" command, and it always answers the same: Result of the command: "copy run tftp" [code] I read everywhere its supossed to prompt asking me tftp server address and file name.
View 7 Replies
View Related
Apr 9, 2013
I have a small doubt with Nexus 7k,5K,2k & 1K.We want to backup the running config to my desktop through tftp.When i tried to backup from Nexus switches showing like below Nexus 7K. [code]
It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config Vdc-all". [code]
It's showing two choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric"
It's showing three choices which one I have to follow "copy running-config startup-config" or "copy running-config startup-config fabric" or "copy running-config startup-config vdc-all". [code]
View 11 Replies
View Related
Nov 6, 2012
I have a 3750 catlyst switch in my network and it is like a distubation switch,And for the nating and dhcp nomadix is using as gateway in the same network. for one of my local PC i need to config the port forwarding in 3750 switch. How to config the port forwarding on 3750 switch,
View 3 Replies
View Related
Nov 30, 2011
I have two 4506 switches in my organization. Recently the office was relocated and when both the switches were booted they ignored the startup config.The config-reg was set to 0x2101. No boot system command was configured.So I changed the config-reg of SW1 to 0x2102 and gave boot system command as stated below.When reloaded the switch booted to ROMMON and I had to manually boot the IOS.I want them to boot normally with IOS.Config of SW2 is not changed since relocation. I am specifying both configs bor your consideration. [code]
View 12 Replies
View Related
Jan 24, 2013
I seem to be having a problem with DNS name resolution after configuring my router (Cisco 3725 running IOS image: c3725-adventerprisek9-mz.124-25.bin) for handling DHCP requests.
Before I made the change, everything was working correctly; I could ping Google.com from a computer inside my LAN and would get response from one of Google's public IP's like normal.
I had a separate DHCP/DNS server running Windows Server 2008 handling the DHCP request and DNS queries.
When I made the change, I turned off the DHCP/DNS server and issued the following DHCP commands to my router:
Code...
View 5 Replies
View Related
Nov 16, 2011
I am in the process of setting up an interop lab for some engineers. The enviornment will consist of some 3750's, H3C's and ProCurves. My concern is that the end user will have Priv-Exec access for CLI usage on the 3750's and they can change the "en" password (I hope they don't but it has happened).Is there a way I can "break in" during the boot process to reset the password? The reason I am doing it this way is because I have an Altiris server with rebuild automation scripts in xpect and I would like to automate the process so I do not have to use a manual factory default reset.
View 5 Replies
View Related
Jul 28, 2012
I was trying to configure an SF 300-24 for use in my home and obviously did something dumb. It was working fine. The f/w was updated and I had configured 2 VLANs. VLAN2 was ports 1-6+GE1 for IPTV streaming and VLAN3 was ports 7-24+GE2 and GE3 for the rest of my LAN. I was plugged into GE4 and was configuring the switch with a laptop. GE4 was the only port still on the default VLAN1. I chaged the default VLAN to VLAN3, which forced a reboot and the switch never came back up. Attached is what I see when I connect to the console port: [code]
I can't access to GUI using it's static IP or it's default IP on any port and the console never reaches the point where I can log in. The System light is flashing green but the boot sequence never progresses past what's in the screen shot. I tried to do a hard reset using the recessed button on the front panel but it does not seem to have any effect, no matter how long I hold it down.
View 5 Replies
View Related
Mar 2, 2013
I am seeing Native VLAN mismatch errors on my 6506 switches as below [code] Will it(VTP Version mismatch) be the issue for getting the VLAN Mismatch Error ?
View 10 Replies
View Related
Mar 9, 2013
I have a WS-CE520-8PC Switch. I have tried a full 30/30/30 reset, factory reset, and I am still unable to access the express setup page. Running Win7 x64 on the host os (have tried windows 2000 and xp)It also wont allow me to access direct managment mode when pressing the admin button for 10 sec.
View 2 Replies
View Related
Apr 3, 2012
I have 2 cisco 6500 in a VSS configuration , All of my Lan access switches are Stack switches and every Stack is connected to the VSS in a Port-channel so basically this is a loop free environment with no blocked ports .As a best practice I left STP in the Background (mstp)which enhanced cisco features to STP should I configure on the Aggregator (6500-VSS) and on the Access switches ?
Because of my topology I dont see the need in configuring most features like Uplink Fast and Backbone Fast but I have configured Loop Guard in addition to UDLD on the 6500 Aggregation Switches (on the port-channels).On the access ports I have configured portfast , bpduguard and guard root (seems a little pointless to configure the two...)
1.should I Leave UDLD on and get rid of LoopGuard and configure Guard root instead ? since LoopGuard cannot be configured with Guard Root.
2.should I configure GuardRoot on access ports if I already have BpduGuard on them ?
3.Is there anything I need to configure on the physicall interface or is everything configured on the port-channel since STP reguards port- channel as a single interface ?
View 4 Replies
View Related
Dec 7, 2011
i have a Catalyst 2960S since 2 days. I am a new user, i like to configure the switch! my first problem is: i have 2 v LAN vlan1/24 and vlan200/24. I'd like to config port1 to be tagged on the 2 v LAN i know from hp port must be tagged. how can i config port 1 to be tagged on vlan1 and vlan200? and port 2 to be untagged in vlan1 and untagged in vlan200?
View 12 Replies
View Related
May 28, 2013
I recently changed the entire configuration on two 6509 switches, and the fibre modules on slot 7 and 8 have gone down on BOTH switches. It would be easy to say that its a hardware fault but I cannot understand how module 7 and 8 can go down on both switches. Initially I thought it maybe due to IOS bug 22-33.SXI2a.bin" so I upgraded it to s72033-advipservicesk9_wan-mz.122-18.SXF12a.bin but it still down.These are the actions I have carrried out to try resolve the issue:
- Reverted back to orginal configs but no luck
- Tried to use "power enable" command but the status light on both modules seems to turn red and then go off again.
- I have also tried to put one of the fibre modules into a different slot but no joy
- Upgraded the IOS from 22-33.SXI2a. to 122-18.SXF12a
I am sure that hardware fault cannot occur on BOTH modules 7 & 8 on BOTH switches after config change.The error in the log shows that modules "failed to bring online because of registration timer event". I understand this means that it is unable to download the image within the allocated time. [code]
View 7 Replies
View Related
Apr 18, 2012
we are planing to run HSRP on our Nexus 5ks (with L3 card) and we use VPC to connect the downstream UCS - Fabric Interconnects to the 5ks. I was wondering if the peer-gateway command is required under the vpc domain config? When you use HSRP with VPC, both the active and standby HSRP peers can forward layer3 traffic, isn`t that the same that peer-gateway would achieve?
View 1 Replies
View Related
Dec 19, 2012
I am attempting to upgrade from a Cisco3945 to a ASR1002. On my Cisco3945, I have interface associated with VLANs. It appears that with the new IOSX, VLAN configuration has changed. Any config to setup a simple VLAN?
View 5 Replies
View Related
Nov 7, 2011
I uploaded a new config file via TFTP to a 3560 switch. What are the order of commands to get it to boot from this new config file instead of the file listed in 'sh boot': [code]
View 7 Replies
View Related
Jan 10, 2012
My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16). This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary. Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules. I think I made an error when I purchased a few of these switch modules: NME-16ES-1G.
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart). I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way. I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16. (Note: The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch. It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet. So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]
View 4 Replies
View Related
Feb 8, 2012
I have a scenario where 15 c500 switches and 5 2960 8 port switch connected to 4507R core switch. There are 10 dhcp pools created on the 4507.
Eg: ip dhcp pool XXXX
network xxxx.xxxxxxx
default-router x.x.x.x
Now the default router is directed to vlans created on the switch i.e vlan 101, 102, 103 and so on. Now the remaining switches connected are configured to be in the same vlan. So the systems connected to the edge switches will get the DHCP ip automatically, Now my problem is after sometime (may be 2 or 3 hrs) all the edge switches are losing configuration automatically even though it's not restarted, even after saving the config on to nvram, everytime I connect the console and check all the saved config is lost?
View 1 Replies
View Related
Mar 15, 2012
how can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch
View 2 Replies
View Related
Oct 30, 2012
After rebooting a pair of 6504's configured for vss, both switches show active on the sup modules. A show switch virtual redundancy however shows the pair working in an active/standby mode. We have 6509's in vss pairs and they show active on switch1 and standby on switch2 led's. For the 6504's switch 1 was booted first and then the second switch about 30 seconds later. Is there something different with the 6504's? [code]
View 4 Replies
View Related
Apr 21, 2013
my environment:
IE-3000-8TC industry-switch
ios: ies-ipservicesk9-mz.150-2.SE2
if i do
vlan 12
name NextVLAN
state active
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.
View 8 Replies
View Related
Aug 6, 2012
On a number of 6500 chassis it appears that linecard 3 did exist at somepoint, but was removed.Problem is that when issuing the 'show int desc' or 'show ip int brie' the ports for the still appear, and indeed same with 'show run' and 'show conf'.
View 1 Replies
View Related
Mar 21, 2012
I have two 5548's in sync mode: I have an existing ACL and I want to add a new line to it, but after I do and try to commit it states the verify failed. [code]
I have to add access list to both switches not in config sync mode.
View 1 Replies
View Related
Aug 9, 2012
I am looking to replace the active supervisor (S720-10G) on our 6509E running in SSO mode. The new module already has the same IOs version as the standby supervisor.Once I have swapped the module how do I know that the config has sync'd correctly other than checking the logs? Is it a case of looking at the "Redundancy Mode (Operational)" state and ensuring is says SSO?Also, is there a command that will force a config-sync if it is running in a mode other than SSO?
View 1 Replies
View Related
