i have a Catalyst 2960S since 2 days. I am a new user, i like to configure the switch! my first problem is: i have 2 v LAN vlan1/24 and vlan200/24. I'd like to config port1 to be tagged on the 2 v LAN i know from hp port must be tagged. how can i config port 1 to be tagged on vlan1 and vlan200? and port 2 to be untagged in vlan1 and untagged in vlan200?
View 12 Replies
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
I got a different scenario from one of my client.My client have two different branch offices and have 50Mbps point to point connectivity between them. All users in both braches using same series of IP pool ( 192.168.224.0/24) in both branches.Both branches he had only Cisco 2960S series switches only. And in both branches he is using IP cameras. He will monitor the assets by accessing IP cameras through the browser.His requirement is, he wants to prioritize the Video traffic( monitoring through the browser) over the normal data traffic.Note: He had a single VLAN only.
View 8 Replies View RelatedI need to set QOS in our new network. We have connected 2 cities together with 700Mbit leased line. On each side we have Catalyst 2960S switches and between them is TRUNK for VLAN 10 and Vlan 20.Vlan 10 is for IPTV (fixed 400 Mb/s for CATV)Vlan 20 is for Internet (rest).Sometimes is happening that Vlan 20 takes more than 400 Mb/s for a few seconds and in this situation we have problems with CATV.Is there any way to make a guaranteed bandwidth 410 Mb/s for CAT - VLAN 10 on this swithces?
View 2 Replies View RelatedI have hybrid network in which I want to configure VLAN on Cisco 2960 S switch. I have unmanged switch where my DHCP server and other servers are connected. Now I created two VLANs on cisco 2960S and they don't talk each other, but as soon as I connect unmanaged switch to 2960S switch, both VLANs start communicating which I don't want. I want to listen server traffic from unmanaged switch from both VLANs but simultaneously I don't want to communication between two VLANs.
View 10 Replies View RelatedWe are trying to setup a new configuration with 2960S as access switchs and a 4507 as a core switch.I want to protect the management IP VLAN of the swich using vrf on the 4507 so we :
SHUT VLAN 1 on every switch (2960 + 4507)
CREATE A NEW VLAN 289 (management vlan) -> IP network : 10.32.126.192/26
L3 VLAN on every switch
VLAN 289 in the VRF XXX on the 4507
create tunk between the switch and the 4507 :
switch mode trunk allowed vlan 200-230
sw trunk native vlan 289
so with this configuration on the 2960 the vlan 289 is UP/DOWN and UP/UP on the 4507 I can access to the 4507 using the IP in the VLAN 289 but i cannot access to the 2960 behind the 4507 CDP connectivity is ok?
Have multiple Catalyst 2960S switches, Cisco 2911 router and ASA 5510 firewall.
On the router have subinterfaces created for the VLAN's Int FA0.0/41 for wirless VLAN setup with IP 10.10.41.100 Int FA0.0/60 for new Voice VLAN setup with IP 10.10.60.100 Internal network is 10.10.10.0/24 and LAN IP of router is 10.10.10.100 Have default route setup to push traffic from the router to the firewall ip route 0.0.0.0 0.0.0.0 10.10.10.251
On the firewall have added the new VLAN 10 (10.10.60.0) to the network object-group Have configured route inside command route 10.10.60.0 255.255.255.0 10.10.10.100 1 Have also added the NAT command nat (inside) 1 10.10.60.0 255.255.255.0
On the 2960 I have my laptop connected to port 45 and I have it configured as follows switchport mode access switchport access vlan 10
I assign my computer a static IP address of 10.10.60.84/255.255.255.0/10.10.60.100 with 10.10.10.11 as DNS server. When I do this, I can ping anything on the 10.10.60.0 network, I can ping anythign on the LAN 10.10.10.0 network. I am able to connect MSN messenger, I am able to do NSLOOKUP and get outside IP addresses to resolve. I am unable to browse the Internet though. I am not sure where the problem is at though. It doesn't make sense to me, as it is setup the same way as VLAN 41 which is the wireless network, and when users connect to that, they get out to the Internet with no issues.
We need to connect several DSLAMs on the 4900 switch, every DSLAM has 4 VLANs configured (VOIP service, MGMT, ADSL Private, ADSL Public), and sends the traffic for each service tagged with appropriate VLAN id according to the table:
VOIP: 608
MGMT: 594
ADSL PRIVATE: 2900
ADSL PUBLIC: 2930
On the DSLAM side it is very simple configuration, just a normal trunk with 4 VLANs transversing the link. On the 4900 I need to isolate the traffic for ADSL PRIVATE & PUBLIC service so DSLAMs connected to the same switch do not have L2 connectivity between them. For VOIP and MGMT they must communicate with each other. DSLAM acts also as a VOIP GW so it must communicate with other DSLAMs for VOIP service. Also VLAN 200 is configured on ME 4900 for switch management traffic.
This 4900 Switch connects to MPLS PE router, which offers L3 VPN service for VOIP & MGMT service, and L2 VPN for ADSL service (PPPoE traffic to BRAS). Fortunately we have ES+ linecard to support many ethernet features. I tried this config:
1) VOIP, DSLAM-MGMT, MPLS-MGMT configured as normal VLANs
2) ADSL PUBLIC & PRIVATE configured as isolated secondary VLANs, primary VLAN for ADSL PRIVATE is 2008, for PUBLIC 2308
3) Configure DSLAM facing ports on ME 4900 as private-vlan trunks
4) Configure ME 4900 uplink port to MPLS PE as a private-vlan promiscous trunk
5) Configure ethernet services on MPLS PE for each tag that comes from ME 4900 (ES+ cards are awesome, i love them:D )
6) Apply L3 VPN service for VOIP and DSLAM-MGMT, and L2 VPN for ADSL service.
But at least this last command should list on spanning tree forwarding state also the ADSL VLANs or not?
Here is the output of the show interface switchport.
Has anything changed in the way of defaults for creating a trunk port and spanning-tree between a 3750x and the newer 2960s? I have one of each I just took out of the box and applied my standard switch configuration template but I cannot get my VLANs that are configured on my 3750X to appear on the 2960S. I find nothing that is blocking and everything seems to be forwarding and I am running out of things to check.
View 5 Replies View RelatedI was trying to configure an SF 300-24 for use in my home and obviously did something dumb. It was working fine. The f/w was updated and I had configured 2 VLANs. VLAN2 was ports 1-6+GE1 for IPTV streaming and VLAN3 was ports 7-24+GE2 and GE3 for the rest of my LAN. I was plugged into GE4 and was configuring the switch with a laptop. GE4 was the only port still on the default VLAN1. I chaged the default VLAN to VLAN3, which forced a reboot and the switch never came back up. Attached is what I see when I connect to the console port: [code]
I can't access to GUI using it's static IP or it's default IP on any port and the console never reaches the point where I can log in. The System light is flashing green but the boot sequence never progresses past what's in the screen shot. I tried to do a hard reset using the recessed button on the front panel but it does not seem to have any effect, no matter how long I hold it down.
I am seeing Native VLAN mismatch errors on my 6506 switches as below [code] Will it(VTP Version mismatch) be the issue for getting the VLAN Mismatch Error ?
View 10 Replies View RelatedI am attempting to upgrade from a Cisco3945 to a ASR1002. On my Cisco3945, I have interface associated with VLANs. It appears that with the new IOSX, VLAN configuration has changed. Any config to setup a simple VLAN?
View 5 Replies View Relatedmy environment:
IE-3000-8TC industry-switch
ios: ies-ipservicesk9-mz.150-2.SE2
if i do
vlan 12
name NextVLAN
state active
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.
I am trying to roll out a new internet router. The problem I am faced with is the LEC only supports VLAN 1227 and greater, specifically they are assigning me VLAN 2528. I am able to create the sub-interface and setup dot1q encapsulation for VLAN 2528, but the vlan database does not have the ability to add VLAN 2528 to it so I am unable to get layer 2 up and going, thus preventing me from getting the implementation done.
View 11 Replies View RelatedI am planning to use a pair of Catalyst 3750 for QinQ over a L2 link (lan extension)
We neeed to have control over what vlans we propagate over this link and we want to avoid incuring costs for every aditional vlan we might need to add to the trunk that would connect to the QinQ provider switches
Our workaround for this would be to ask the provider to give us an end to end vlan that supports MTU-1504B (QinQ frame size) and connect our switches to this.
I have a sf300 with (2) vlans (1) ] vlan for data and vlan (100) is my voice vlan I have Vlan (100) tagged traffic, and my VoIP pbx as an access port only to vlan (100) all other ports are trunk ports with vlan (100) tagged and vlan (1) untagged traffic. I get no outbound audio on calls I can call out hear them fine they cant hear me. I am wondering if my tagged traffic leaving the phone is being striped and if so were. I have CDP turned off.
View 1 Replies View RelatedWe have a Cisco Aironet 1130AG Wireless AP (firmware 12.4) and have a guest wireless network (internet only) and corporate wireless network configured on it. They are kept separate by having different VLANs assigned to them. When a laptop connects to the guest network I see the DHCP request go out and it is tagged with the correct VLAN. The problem is when a laptop connects to the corporate network I see the DHCP request go out but there is no VLAN tagged on the packets. This causes a problem because both of our DHCP servers (on VLAN 1 and 3, remote DHCP servers no DHCP running on the Aironet [Doesn't seem like this version has a DHCP server]) are sending responses and sometimes the corporate user will get an IP address on the Guest subnet.
Our corporate network is setup on VLAN 1 which is configured as the Native VLAN on the Aironet. Will this cause the Aironet not to tag these packets with any VLAN information? Any other thoughts as to why it isn’t tagging these packets to a VLAN?
If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View RelatedWe are trying to setup a WAP4410N with 2 SSID's. One SSID for our private network and the other for guest internet access. On the VLAN and QoS page there is a setting for priority. What would be the suggested values for this setting? We obviously want our private network to receive priority over our guest network.Also, does VLAN Tag setting need to be on Tagged to determine private from guest traffic?
View 2 Replies View RelatedI have recently split the voice vlan (10) from the data network (1), and am wondering why my catalysts and router do not require an interface Vlan10 statement. In the past I used OpenBSD boxes to do the routing, and I first needed to configure vlan 10 on the interface before I could get inter-vlan communication to work. With these Cisco devices it works, and I am wondering if it is because of VTP, for the fact that the ports maybe just pass all traffic, or is there some other explanation? Below is the setup, and firmware is up-to-date on all of the devices.
When I plug a phone into the POE SGE, the phone turns on, obtains an address on the proper subnet, and conversations are clear (whereas without the ip nat inside on the new subnet the calls had a lot of static). Possibly the reason that it works is because the phones properly create the tcp/ip packet, and it hops over the trunks and creates the states so that traffic routes back properly. I will install wireshark to see exactly what is going on, but is there a simple explanation that I am overlooking?
I need to enable multicast routing on 2960s but the command "ip multicast-routing" isn't available on my release (12.2.(55)).
From which release this command is available?
I have C2960S-48FPS-L and C2960S-24TS-S both of them are using C2960S-UNVERSALK9-M image with version 15.0(2)SE on both I run "mls qos"
and on 48FPS-L I run "mls qos map cos-dscp..."on 24TS-S I cannot run it. there is no such command. there is just "mls qos rewrite..." and "mls qos srr-queue..." variants.
I thought that one image give the same set of commands...?
while i am configuring a port on switch .The switch reloads.After reload the show version says,System returned to ROM by bus error at PC 0x458F6C, address 0x0,show version from the effected switch is,Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1).
View 4 Replies View RelatedI am currently having an issue with connecting a Catalyst 2960-S switch to a Small Business SG300 switch. When I connect them they are unable to form a link. When I do a show spanning-tree it says the mst link is in dispute.
View 1 Replies View RelatedI read some papers about QoS. The thing is that I have to implement 30 switches with QoS to connect to a lot of Cisco IP phones. The switches are Cisco 2960S with code image "C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3". Should I use autoQoS feature or manually configure them?. How should I treat uplinks between access switchs and core/distribution? I have a lot of doubts regarding queueing, because all the info I had read its for another model/image.
View 4 Replies View RelatedI'm looking at the WS-C2960S-48TD-L and have a question about the uplink ports. Is it possible to mix 10G on one uplink and 1G on the other? The datasheet says 2x10G SFP+, 2x1G SFP so I am thinking mixing is not possible.
View 6 Replies View Relatedjust got new hardware and decided to try the newer USB port for IOS upgrades. I could not get the switch to recognize my 2gig flash drive. Do I need a proprietary stick or special format?
I also noticed when I removed it the switches crash dump and rebooted?
When using dynamic configuration tools, if I choose 2960 (not 2960s), I have the option to choose RPS2300 as redundant power, but when I choose 2960s, I cannot choose RPS2300. However, in a document describe both 2960 and 2960s, it said that RPS2300 can be used. Does RPS2300 support 2960S?
View 1 Replies View RelatedRecently I'm working with my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET,This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.Access-list 100 permit ip any any dscp default,class-map match-all QoS_Floor_Limit, match access-group 100.
View 1 Replies View RelatedI would like if is possible to stack a Cisco 4900M with a 2960S. I know it is not the most common situation but i need it.
View 1 Replies View RelatedI would like to enable port security to hardcode the MAC address on the ethernet switch. There are 5 ethernet ports in the same ethernet switch to be assigned for one person (one note book), e.g. port 5, 6, 15, 16 and 23. The model of ethernet switch is cisco 2960S and one MAC address is configured on 2960S.
1. Does 2960S support this requirement to allow input the same MAC address to 5 different port?
2. If yes, can ethernet switch "smart" enough to forward the packages to "active" ethernet port which is connected to notebook and the rest of four ports are inactive.
3. if no, any solution or any work around to achieve this requirement
We are designing a LAN Network for ourselves.The proposed design is as follows:
4 x 2960S switches in a Stack Access-Stack-I 4 x 2960S-PoE switches in a second Stack Access-Stack-II
2 x 3750X switches in a Stack Core-Stack
Now I would like to connect it in the following manner ?First,I would like to use EtherChannel using the 10Gig LinksSecondly, I would like to use Cross-Stack EtherChanel too.I have given a graphical illustration of the connectivity Now my Qs: a) Will the 2960S supports EtherChannel using the 10G links and the 3750X too... b) Does the proposed solution will work... or It will have any problems.
I have two switches (2960S's) both with IP Phones on VLAN100..We need to monitor voice traffic via a monitor port on SW1 of all VLAN100 traffic on both switches.The following is what we have configured, but we cannot see VLAN100 traffic on SW1
According to Cisco doco you cannot have a SPAN and RSPAN on the same session, however since these are two sessions on SW1, I would have thought it to be OK.
