Cisco Switching/Routing :: Can't Reconnect To 881 After Changing IP Address
Jan 1, 2013
I have a new 881 router and am simply trying to change the ip address from the default 10.10.10.1 to 192.168.15.1
I tried doing this both in the CCP Express app loaded on the router, and also using the desktop CCP client. I can change other parameters without any problems, but when I change the ip address of the vlan the program hangs (as expected since the ip address should be changing). I then try to open it back up and reconnect but get no response from the router.
I can ping it no problem, and the http server is running according to the serial terminal.
View 1 Replies
ADVERTISEMENT
Jul 15, 2012
well i had the same problem because i got bored and i was like hmm i wonder if i can change my IP and i tried it and i had the same problem but when i did system restore it still did not work, now i have to get a new operateing system...
View 10 Replies
View Related
Jun 11, 2011
How i can change my ip address without changing my internet connection??
View 3 Replies
View Related
Sep 23, 2012
I have VLAN X with MTU 9216 on Switch-A. I also have VLAN Y with MTU 9216 on Switch-B. But not their SVIs are MTU 9216.They are not communicating to each other on packet size of above 1500. This is because SVI VLAN X and SVI VLAN Y connect to each other through SVI VLAN Z (Point-to-point Layer-3 connection between two switches). Although SVI VLAN X and SVI VLAN Y communicate through SVI VLAN Z, this inter-link port is a trunk port carrying other VLANs but VLAN Z is a native vlan for which SVI VLAN Z is defined.In order to make it work.
1. Do I need to change SVI VLAN X and SVI VLAN Y to 9216?
2. Change MTU for VLAN Z and SVI VLAN Z to 9216?
3. DO I need to change MTU sizes for other VLANs that are on TRUNK port?
View 3 Replies
View Related
Oct 2, 2012
We have two 6500s. One is running in power redundant mode and the other is running in combined mode.We need to change the one running in combined mode to redundant mode to ensure it can run ok on one supply if needed but I have a couple of questions.
1. Assuming that we are not oversubscribed on the power allocated, does changing the mode cause any disruption?
2. The switch running in combined mode seems to have allocated some power for an "Inline Local-Pwr-Pool" which is not allocated on the switch running in redundant mode (see attached). Does this allocation will be needed if we change the power mode?
View 1 Replies
View Related
Sep 5, 2012
I have a MPLS cloud in our data center. I want one network coming into our core router to have a different default route than the other networks coming in. I'm getting hits on the acl but the route isn't applied and goes to the default route that is configured in the router. I have other PBR for setting local-preferences and as-paths and they are working fine.
The router is a 7206 Version 12.4(11)T3
!
ip route 0.0.0.0 0.0.0.0 1.2.3.4
!
ip access-list extended 2nd_Default_Route
[Code].....
View 1 Replies
View Related
Nov 7, 2011
I just tested IP SLA with tracking on a 3750 12.2(46)SE. And the configuration was simple enough and tested fine for redundant static routing: [code] Then I tried to do the same on a 3560 switch running 12.2(55)SE3. ip sla went in fine. But when I went to put in the track I was presented with "list boolean and" (for example) after the track and the identifier.I tossed in the ip sla "10" as the object. But shopw track shows the boolean AND as down. I don't get why the track feature is different in two switches so close in IOS version. How do I get the 3560 to track the ip sla as my 3750 does?
View 3 Replies
View Related
Aug 27, 2012
I am going to change a running 6500 switch. I am missing a best pratice doc for changing a cisco switch configuration. My question is if a startup-config has an error (due to typo mistake, or due to comands not supported on latest IOS) and I do copy tftp startup-config then what will happen ? I want to make sure when I do "reload" the switch then it should boot normally with the latest startup config !
View 3 Replies
View Related
Oct 24, 2012
I have a client who is changing their management IP scheme as a bridge to replacing equipment and much of the old equipment (Catalyst 4000) is running CatOS and I am a bit weak in CatOS. The existing Management IP is setup as follows:
set interface sc0 1 192.168.252.209/255.255.255.0 192.168.252.255
set ip route 0.0.0.0/0.0.0.0 192.168.252.1
What we want to change this to is as follows:
set interface sc0 110 192.168.197.209/255.255.255.0 192.168.197.255
set ip route 0.0.0.0/0.0.0.0 192.168.197.1
The devices are spreadout over a large area and visiting each device is almost out of the question due to a time deadline I was wondering if I run this set of commands will this allow me to keep a remote session (SSH) running until the change is complete?
set ip route 192.168.197.0/255.255.255.0 192.168.197.1
set interface sc0 110 192.168.197.209/255.255.255.0 192.168.197.255
set ip route 0.0.0.0/0.0.0.0 192.168.197.1
View 5 Replies
View Related
Apr 18, 2012
I have a 3560 switch with the following ports config [code] I would like to use theses ports on a different vlan to connect 4 pc's to them. Can I just remove them from the vlan, remove the trunk switchport and set up on the vlan i want them on with no trunking?
View 5 Replies
View Related
Feb 25, 2012
I have 3750 Switch and need to activate the ipservices on it , it is need a license file to switch from ipbase to ipservices , if i installed the ipservices image from cisco site , do i still need an activation key to use it??
View 7 Replies
View Related
May 15, 2013
we ordered a data e-delivery PAK L-SL-29-DATA-K9= (FOR A 2900 SERIES ROUTER) but after we received the PAK we discovered that the client actually has a 1900 router. Any easiest way of rectifying this mistake so that we can use the PAK on a 1900 series router?
View 1 Replies
View Related
Oct 14, 2012
We have two 6500 core switches and one(primary) of them is running in VTP transparesnt mode and the other (secondary) one is running in VTP client mode. I would like to change the VTP mode of the second switch to transparent mode. Would it cause any issue. I guess i have to create VLANs onto the switch.
View 7 Replies
View Related
Jul 9, 2012
I have 2 SG300 switches, in layer3 mode, lag'd together for high availability, serving 2 Dell R815's and a Dell Equallogic 4100 for virtualisation. I have setup a number of vlan's, network traffic, mgmnt traffic, iScsi, vMotion etc and they seem to work.
However, Equallogic unit suddenly became unavailable to view for managment yet maintained iscsi traffic for the servers ok. After much head scratching, noticed that one of my SG300's had the vlan ports assigned to various vlans had *automagically* changed there assignment, ie tagged changed to excluded, but only for one of the iscsi traffic connections and the mgmnt port, both coming from the Equallogic, the other iscsi continued its assignment fine. The other SG300 hasn't changed. Guaranteee no one has been into change it and no changes have been made to Dell servers or Equallogic.
Q. Is there any circumstance where the switch can change the port setup itself? or is there any external circumstance that would trigger that change either?
This has now occured twice. The setup is running as a test lab, not in production until all setup is complete, then it will replace our existing harware.
View 1 Replies
View Related
Feb 5, 2012
I've got a 3750 stack with a 3750-48p being switch 1 and a 3750-12s being switch 2 and switch 2 is the master. I would like to change the stack member numbers. I would like the 3750-12s to be switch 1 and the 3750-48p to be switch 2. I undertand I will have to reboot the stack for the change to take affect but here are my questions:
- How would this change affect the stack running-config ?
- will the switchport config follow the change ?
switch 1 provision ws-c3750-48p
switch 2 provision ws-c3750g-12s
View 1 Replies
View Related
Dec 22, 2012
I am having trouble after creating a management vlan (99) on a 3550 switch.I have configured the vlan (99) and given it an IP (192.168.1.100) and a default gateway (my router address - 192.168.1.99).I can ping to the switch from a PC and vice versa. The management VLAN IP is fine but now I cannot ping to the router from either the PC or the switch.It seems that just by adding VLAN 99 with it's own IP address has now prevented pings from the switch/ PC to the router ?Due to the fact that I have created a new switch management VLAN with an IP, does this mean I have set up the router as a 'router on a stick' scenario ? [code]
View 4 Replies
View Related
Oct 30, 2012
we have 6500 series switches by default all port channel loadbalancing is src-dst-ip.Now we have a requirement to change LACP load balance method to src-dst-port.
1) If we change LACP loadbalance method whar are the effects we are going have on our core network and all the existing servers
View 3 Replies
View Related
Oct 24, 2012
I am installing a several new Cisco VM servers. The VM hosts are losing connectivity when we apply the etherchannel config in the core stack. VMware has stated that the etherchannel load balance needs to be src-dst-ip in order for the etherchannel to work.However, my current stack has 2 etherchannels configured to other switches through out the bldg in network closets. The current load balance configuration is src-mac.My question....when I make the change to src-dst-ip, will my network connectivity go down? I saw there was an older article on this that doesnt provide an answer just a work around. Here is the article. [URL].
View 1 Replies
View Related
Nov 22, 2011
I am getting ready to make changes to our spanning-tree configuration in the data center. In familiarizing myself with the network I noticed that our core switch (6509) wasnt the spanning-tree root for the datacenter.
When I enter the spanning-tree priority command on the central 6509, will it be a hitless change (i.e. will there be any disruption to the network) ? All switches are connected to the core/central 6509 by a direct connection.
I know that when I change from pvst to rapid-pvst that the network will bounce because of the change in configurations to all of the switches.
View 3 Replies
View Related
Sep 24, 2012
1) current switch have below mentioned switch stack details
.
switch#sh switchSwitch/Stack Mac Address : fcfb.xyz.8b80H/W CurrentSwitch# Role Mac Address Priority Version State----------------------------------------------------------*1 Master fcfb.xyz.8b80 10 0 Ready3 Member 2893.xyz.3180 1 0 Ready
2) I am in process of changing switch member number from 3 to 2 , I executed the command on the global config mode " switch 3 renumber 2 "but I yet to reload the switch .
here I have I doubt . as currently the ports module are fas 1/0/1-48 and fas 3/0/1-48 under respective vlan . once I reload the switch is the switch port module number will get change to fastethernt 3/0/1-48 to fastethenet 2/0/1-48 ??? . if it happens the vlan configuation which configured on the fas 3/0/1-48 module also get configured automatically or I need to configure manually
3) as i said i have execuated the command : "switch 3 renumber 2 " , how to remove this or revert the change , as i checked in the running config this command not exist .
switch ( config) # switch 3 renumber 2WARNING: Changing the switch number may result in aconfiguration change for that switch.The interface configuration associated with the old switchnumber will remain as a provisioned configuration.Do you want to continue?[confirm]Changing Switch Number 3 to Switch Number 2New Switch Number will be effective after next reboot
View 4 Replies
View Related
Nov 28, 2012
I have a pair of data center core 6500 is running a single EIGRP AS with the standard core redundant cross connects. Recently an SVI sub net was expanded from a /24 to a /23 and dropped out of the EIGRP routing table. Subsequent trouble shooting lead to the router id being one using an IP address that is no longer active IP address.
Reviewing old configurations I found, that year ago, the ip address used for the EIGRP router-id (10.100.106.3) was removed from the active interface and changed but the EIGRP router-id was not updated. The switch has not been rebooted since, no loop back is configured and there is not a higher IP configured on an active interface. Reviewing documented material on it, I cannot find anything specific on this condition but do see in the discussions on duplicate IDs, that new route updates can be a problem. I know how to update the router id but I am looking for confirmation on what would be the impact when I add a new loop back and manually configure the router-id under the EIGRP process with the new loop back IP.
My assumption is an EIGRP update and route re convergence with the standard 90 seconds of outage. How to confirm this is assumption is correct? I have no test bed to find out myself without doing this on the active cores.
show version Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI5, RELEASE SOFTWARE (fc2) show inventory NAME: "WS-C6504-E", DESCR: "Cisco Systems Cisco 6500 4-slot Chassis System"PID: WS-C6504-E VID: V01, SN: <deleted> NAME: "1", DESCR: "WS-SUP720-3B 2 ports Supervisor Engine 720 Rev. 5.3"
PID: WS-SUP720-3B
EIGRP configuration is pretty basic:
router eigrp 10
network 10.0.0.0
redistribute static
passive-interface Vlan110
passive-interface Vlan80
[code]...
View 1 Replies
View Related
Mar 25, 2012
Will there be some pause in traffic on formed ether channel interfaces (4500E switch), when i will change the default ether channel load balancing method to src-dst-port (or any other non-default method)?
View 1 Replies
View Related
Apr 6, 2013
I need to change the IP address of existing primary cisco ACS 4.2 (windows based). What is the required procedure to change the IP address?
View 4 Replies
View Related
Feb 12, 2011
I tried changing my ip address using ipconfig / release. I tried to fix what I did using ipconfig /renew but it tells me no operations can be performed on local connection 5 while it's media is connected.
View 12 Replies
View Related
Apr 9, 2012
I am trying to configure a router with a satellite connection. I am following a HughesNet guidline. At step four after typing in the required IP address , nothing happens.There is no place to type user name and password.
View 2 Replies
View Related
Sep 21, 2011
How to change ip address in windows 7?
View 1 Replies
View Related
Jul 11, 2011
I am connected to a static ip network. This network sets local ips to connected computers but general ip is the same: static ip of network. When i go to "whatismyipaddress", I can see this static ip. I want to change my ip address. I have no chance to use proxy server or router connection. Is there a way to change my ip address? (Because some sites ban ip address, ex:rapidshare etc. and I need to change my ip)
View 1 Replies
View Related
Sep 30, 2012
I found this good guide how to do it, but some things remain unexplained to meI would like to get more information about step:3. Change the IP address of your current PCMaybe more questions will follow, but that's the only problem I am having right now.
View 11 Replies
View Related
Jun 10, 2012
I've had the same IP address for years and want to change it to a new one - I have a dynamic IP but for some reason it will never change.It looks as if it's always static-what settings I need to change on Windows 7 to get it to roll over onto a new IP address?
View 1 Replies
View Related
Nov 24, 2011
Trying to change my IP address in windows 7. I downloaded Desktop Central 7.Server and Desktop Management Software: Now what am I suppose to do?
View 2 Replies
View Related
Nov 16, 2011
I added a new server and created a new static NAT assignment on the ASA 5510 to the server's IP. When I browse to the web to check what public IP it's reporting, it shows the wrong IP. I disabled the network interface on the server, ran "clear xslate", reenabled the network interface, ran "sho xlate" and while the correct translation was in the table, the server still reported the wrong IP address.I even ran a packet trace and it showed the IP address being correctly translated to the proper public IP, but when I browse to the web I get the same erroneous public IP. [code]
View 8 Replies
View Related
Aug 8, 2012
How can I change my ip address on windows 7. Someone hacked my computer before and now im afraid that he will do it again. I want to secure it by changing my ip address..
View 2 Replies
View Related
Jul 11, 2011
My Network is running Windows Server 2003 and with more than 150 Users. But last week, I notice that a program is changing my DHCP server IP Address scope.
View 2 Replies
View Related
