To do this I’ve created another Dialer and re-assigned the atm interface (atm0/0/0) to it. Then I’ve done a shut and then a no shut a min or two later. To my surprise the debug ppp negotiation showed the user name from Dialer1 and then the line was back in my multi link bundle.
My relevant Config is below:
interface ATM0/0/0
no ip address
[Code]......
I want to configure my router to use 2 ADSL lines each with a dialer and a modem in RFC2684 mode. I have a 2821 (IOS 12.4) with an HWIC-4ESW.
My network topology is like this :
ADSL Modem 1 (RFC2684) --
(Fa0/0/0)
Router -- (Gi0/1) MyLAN
(Fa0/0/1)
ADSL Modem 2 (RFC2684) --/
1. I configure my DSL Modem in RFC 2684. The first use 172.16.0.2/29 and the second 172.16.0.3/29. I connect this devices to Fa0/0/0 and Fa0/0/1.
2. I configure Vlan1 to use the network configured on my modem :
interface Vlan1
ip address 172.16.0.1 255.255.255.248
3. I try to ping my devices :
#ping 172.16.0.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.3, timeout is 2 seconds:
!!!!!
[code]....
My WLC 4404 runs with Software Version 5.2.193.0. The built-in IOS for AP is Version 12.4(18a)JA2.I run into problem same as in CSCta29484 Bug (Radio stops beaconing for 10-second period).I would like to try fixed image for LAP without upgrade WLC. Is it possible?
View 5 Replies View RelatedI´m Trying to synchronize the clock with NTP server external, these ntp server only support NTP version 3.Can I change the NTP version in the ACE4710 Appliance to support the ntp server external?If is possible, How I can change it ?
This is the version:
Cisco Application Control Software (ACSW)
TAC support: [URL]
Copyright (c) 1985-2011 by Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
[code]....
McAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies View RelatedHow are asa5540 in high availability mode upgraded for their versions.
View 1 Replies View RelatedWe have recently deployed several Ciso 887VAW (IOS 15.1(4)M4) to customer premises and I have come to realise counters show extremely high (not at all accurate) output rate and packets on all of them. [code]
View 2 Replies View RelatedI have an 837 ADSL router that the customer is upgrading from a 3 meg circuit to a 10 meg circuit.
The previous vendor used PPOE for connection and we used a dialer 1 interface to make the connection with a user name and password.
The new connection is a straight WAN DHCP no username or password needed.
I realize I can change the dialer interface from negotiate to DHCP but do I still need it ?
Can I replace the dialer 1 interface with IRB ? Should i just keep the Dialer 1 interface since the device is currently set that way and just remove the PPP negotiation from dialer 1 ?
I have applied a crypto map (fo ipsec vpn) on the dialer interface (for PPoE connection) in Cisco 2800; every time when the router restarts the crypto map is removed from the dialer interface even though i save the configuration every tim when i apply the map on the interface. Is there any way that the crypto map remains there on the dialer interface after the restart of router.
View 1 Replies View RelatedI am having an issue with Cisco 1812j Router.
I have 2 1812j router. One router I accidentally lost the password so I reset the password as following link. [URL]
After that I could not submit "dialer" command. Like this.
c1812j-01(config)#int bri0c1812j-01(config-if)#d?dampening default delay descriptiondot1q dot1x down-when-looped dxi
c1812j-01(config-if)#
There is no choice to use "dialer" command.
The other Router is as below which looks ok.
c1812j-02(config)#int bri0c1812j-02(config-if)#d?dampening default delay descriptiondialer dialer-group dot1q dot1xdown-when-looped dxi
I guess I did something wrong to reset the unit.
How to make a Cisco 881 router finally work. I have the following configuration:
Current configuration : 2964 bytes
!
! No configuration change since last restart
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[code].....
As much as I understand, the VPN tunnel is active.I can access the Internet, but I cannot access anything through the VPN tunnel.
having some issues with a configuration using a Dialer interface. The interface comes up and the VPN tunnel comes up, but cannot access any network resources or the Internet.
The things that concern me most are my access lists as I have the static IP address that we are assigned via PPPOE - the IP never changes, but not sure if I can define it in the ACL or if I should be using an ANY tag.
Note: I've changed some IPs and username for security reasons.
!version 15.0service tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryptionservice sequence-numbers!hostname C2911-OTO01!boot-start-
[Code].....
I am trying to copy a setup from a Nortel IAX100 where the carrier provides two ATM PVC's over ADSL - one for voice (VoIP) and one for data (IP). Relevant lines from the backup of the IAX's configuration include the following for the PPP authentication over the voice circuit:
<wan_8_32>
<entry1 vccId="1" conId="1" name="Voice" protocol="PPPOE" encap="LLC" firewall="enable" nat="enable" igmp="disable" vlanId="-1" service="enable" instanceId="1509949441"/>
</wan_8_32>
<pppsrv_8_32>
<ppp_conId1 userName="" password="" serviceName="" idleTimeout="0" ipExt="disable" auth="auto" useStaticIpAddr="0" localIpAddr="255.255.255.255" />
</pppsrv_8_32>
The null username and password for the PPP connection have me a bit stumped. Does the PPP connection not use any authenetication at all? (Is that possible/likely? How could I deubg it?) Or does does the IAX100 supply a chap/pap response with null credentails? (If so, how would I duplicate that using an instruction to a dialer interface?I am configuring an 877 with 12.4T and advanced IP services.
I have found this workable cisco 1841 config on the NET. From this link: [URL]
But it is doing source NAT from FA0/1 to Fa0/0. If we need to bridge, is it need to use “ip unnumbered”?
See my config below” 1841 config for Unifi, with ip unnumbered“, can work?
1841 config for Unifi, with NAT
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
! !
! Works perfectly on Cisco 1841, IOS v12.4(24)T !
[Code]....
We have a dsl connection on 897 dsl router at the customers HO.The telephone line is directly connected to router we configured dialer with username and password and it takes a static ip of 212.249.213.xxx.Now he has some branches that are connected through wireless links and he has arranged for a subnet of 8 public IP's in the range 72.70.245.xxx
Can we some how use these public ip's as secondary in the routers dialer interface and assign to the servers in the branches so that it can be accessed through web.
We are a new call center company and want to configure the network to setup the predictive dialer, work properly.how a network could be setup to configure predictive dialer.
View 2 Replies View RelatedI am configuring ISDN Interface on 2 Cisco 886VA Version 15.2(3)T . I am unable to set ppp multilink on the BRI0 interface and on the dialer interface. It's like the command doen't exist anymore.How can I fix that so that i can have 128 K bandwidth between ma 2 sites ?.
Router1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router1(config)#int bri0
Router1P(config-if)#ppp multilink
[code]....
I have two 3825's. Each has it's own ISP connection. Nat is configued for both. They have an ethernet connection between them and I'm running OSPF between the two so the routes propogate. I have qty 11 Dialer interfaces configured on each router (each router has an exact copy of the other routers dialer interface). However, I only want the Dialers up if the ISP connection on the mated router goes down. Much like HSRP I need one to preempt and be active if both ISP connections are up. When one goes down the other Dialers must come up. Each dialer sends a Dynamic DNS host name and IP address pair to DynDNS.org. So I cannot have both up otherwise the DNS names will bounce between ISP#1's IP address and ISP#2's IP address (back and forth). Let me know if any option exists to make this happen. As an aside the ISP's are providing me DHCP addresses so I cannot work off of an IP, it has to be the physical interface (i.e. Gi0/0).
View 1 Replies View RelatedWe are trying to take ADSL interface into another VRF i.e (ip vrf forwarding VRF2 under dialer interface), the ip address negotiated command disappears, and although the dialer interface becomes up-up state, the adsl interface does not get an IP address dynamically.
Tried:
1) to reenter ip address negotiated again after changing the vrf of the interface, still the dialer interface shows "no ip address" under configuration
2) ppp ipcp accept-address again does not work.
the IOS version:c880data-universalk9-mz.151-2.T1.bin
I have the below configurations done on a 2900 router. [code]I would like to know, if the IP address assigned to dialer1 interface "20.1.2.133" would be listed in "show arp" ?, as it failed to list on our router and I want to know if this is an expected behavior ?
Secondly, does self ping 20.1.2.133 (dialer interface IP) work ? [code]
Is it possible to establish a interface dialer on a layar 3 switch?Or is it only interface for routers?I have a c3750 switch (WS-C3750G-24T), and when i try to establish a dialer interface i get an error message:
[code]...
I have a NETGEAR Wireless-N 150 Router WNR1000 v2. I am trying to configure it for my LAN which has a DIALER. [code] I tried to configure my NG but it is unable to connect to the network on its own. I have to use CONNECT dialer from my PC to connect which is useless because I can't use my wi-fi enabled devices to access network.
View 1 Replies View RelatedI have a cisco 870 router which I'm trying to connect to my ISP all the interfaces are in a up, up state. But I'm unable to ping any IP address on the internet. When I do a debug ppp I can see that the username and password are correct with the dialer 1 interface as there is no errors and I can see success. But when I shutdown the atm0 interface and then do a no shutdown I see a message called authentication failed.How does the atm0 interface work with the dialer,Also I spoke to the ISP and they can't see any connection being made but the debug shows success. I also get a default gateway via the ISP but it is the incorrect default gateway as I can't ping the internet and the ISP confirms that the default gateway is incorrect.
View 33 Replies View Relatedi am having cisco 881 router i want to know whether i can configure dialer interface with username and password for my dsl internet connection.
View 2 Replies View RelatedCan we use ACS 4.1 version recovery disc on 4.2 verison to recover the forgotten password.
View 1 Replies View Relatedwhich version of prime infrastructure supports wlc5508 version 7.4
View 2 Replies View RelatedI have a big problem with my Cisco 1841 and the WIC-1AM-V2 in Slot 0.I got the task, to test if it is possible, to build up a connection (Dial on Demand Routing) to a remote modem, which is connected to a console port of another Cisco 1841, with the integrated modem card over POTS from the CLI of the router. My router will only dial out to the remote modems and only if its needed.I am connected to the router with the integrated modem card over a console cable on the console port. The remote modem is also connected to the console port of the remote Cisco 1841.
I found out, with my Dialer Profile configuration, it is possible to build up a connection. I configured a dialer list, that specifies that all ip traffic is permitted an interesting for my dialer interface. So a telnet or ping brings up my dialer, which brings up my Async interface. With the "show line" command, I can see that the TTY line, connected with the Async0/0/0 Interface is in use for 5 minutes, because of the "exec-timeout 5 0", which is configured on the remote router. Now the problem is, in this 5 minutes, I can not use a remote telnet on this line with my loopback interface, because the line is already in use and I get a "connection refused". The first telnet I use runs in a timeout, because the remote host is not responding. When I dial out directly from the modem card and not from the CLI with the AT-commands, I get also the connection and with a return i get the login prompt. I will post my actual config, so that you can see maybe a mistake I did or which command I must use, to get a working connection. [code]
provide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View Relatedi am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View RelatedI am using a range of IPs from my inside LAN for my IPSec VPN clients. For example my inside network is 172.16.1.0/24 and I have a pool setup like this: ip local pool vpnpool 172.16.1.200-172.16.1.210 mask 255.255.255.0.
Before the upgrade to 8.4 it was working and now it isn't. Clients can connect and pickup and IP but can't cominuicate with the inside LAN. I think I have to do manual NAT to nonat this range. So I want to try the following:
object network obj-vpnpool range 172.16.1.200 172.16.1.210 nat (inside,outside) 1 source static any any destination static obj-vpnpool obj-vpnpool
However there are two things preventing me from doing this:
1) When I try to create obj-vpnpool I get an error stating that this object overlaps with local pool
2) Even if I create the obj-vpnpool with a non-overlapping range, when in the VPN config I don't have an option for selecting obj-vpnpool.
ON ASA, I understand that we can assign a static IP for a specific VPN client, or we can use a DHCP pool to assign IP. Now if I want to create DHCP pools, say pool_A and pool_B, for user A, B and C they use the IP from Pool_A, and user D, E, and F they get the IP from pool_B. Is there a way to do this in ASA?
View 4 Replies View RelatedI have Remote Access VPN users (IPsec) who are terminated on Cisco ASA 5520 (v8.2). For those users, AAA is done on the ACS. Group-policies and tunnel groups are defined on ASA. Initialy I had all VPN users defined on ASA and group policies were associated with each user. Each group policy had it’s own IP pool for users. Now, I moved users to ACS. How can I associate group policy, defined on ASA, with users group defined on ACS? Is it possible that ACS send to ASA information about IP pool for different group policy? Users will use ONE vpn profile BUT based on the Active Directory group they belong to they obtain a different IP address for each group.Can it be done ? ACS version is 5.2.
View 1 Replies View RelatedWe have the configuration below set up in a 3560 switch (addresses and names modified for privacy). We are running out of dynamic IP’s in the current pool (6.35.159.0 – 6.35.159.255). We have a new set of IP’s that we can use (6.44.56.0 – 6.44.57.255 – an additional 512 addresses). Although I can figure out the commands to add a new dhcp pool, secondary subnet, etc., I’ve never done this before so I’m not sure of everything I need to do. The end result I need is that the 3560 needs to be able to hand out IP addresses from the current and new pool to anything connecting to vlan 300 – our datanet where computers access the Internet. What I need to do as far as modifying the vlan, adding the secondary subnet, defining helper IP’s, gateways, whatever, so that computers connecting via vlan 300 have Internet access via either of the pools? I have been told that all I need to do is create the pool, but not sure if that is correct...
[code]....