Cisco WAN :: 837 - Replace Dialer 1 Interface With IRB?
Jun 21, 2011
I have an 837 ADSL router that the customer is upgrading from a 3 meg circuit to a 10 meg circuit.
The previous vendor used PPOE for connection and we used a dialer 1 interface to make the connection with a user name and password.
The new connection is a straight WAN DHCP no username or password needed.
I realize I can change the dialer interface from negotiate to DHCP but do I still need it ?
Can I replace the dialer 1 interface with IRB ? Should i just keep the Dialer 1 interface since the device is currently set that way and just remove the PPP negotiation from dialer 1 ?
View 1 Replies
ADVERTISEMENT
Feb 10, 2013
We have recently deployed several Ciso 887VAW (IOS 15.1(4)M4) to customer premises and I have come to realise counters show extremely high (not at all accurate) output rate and packets on all of them. [code]
View 2 Replies
View Related
Jul 4, 2011
I have applied a crypto map (fo ipsec vpn) on the dialer interface (for PPoE connection) in Cisco 2800; every time when the router restarts the crypto map is removed from the dialer interface even though i save the configuration every tim when i apply the map on the interface. Is there any way that the crypto map remains there on the dialer interface after the restart of router.
View 1 Replies
View Related
May 11, 2013
How to make a Cisco 881 router finally work. I have the following configuration:
Current configuration : 2964 bytes
!
! No configuration change since last restart
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[code].....
As much as I understand, the VPN tunnel is active.I can access the Internet, but I cannot access anything through the VPN tunnel.
View 3 Replies
View Related
Jan 9, 2011
having some issues with a configuration using a Dialer interface. The interface comes up and the VPN tunnel comes up, but cannot access any network resources or the Internet.
The things that concern me most are my access lists as I have the static IP address that we are assigned via PPPOE - the IP never changes, but not sure if I can define it in the ACL or if I should be using an ANY tag.
Note: I've changed some IPs and username for security reasons.
!version 15.0service tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryptionservice sequence-numbers!hostname C2911-OTO01!boot-start-
[Code].....
View 1 Replies
View Related
Oct 15, 2012
I am configuring ISDN Interface on 2 Cisco 886VA Version 15.2(3)T . I am unable to set ppp multilink on the BRI0 interface and on the dialer interface. It's like the command doen't exist anymore.How can I fix that so that i can have 128 K bandwidth between ma 2 sites ?.
Router1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router1(config)#int bri0
Router1P(config-if)#ppp multilink
[code]....
View 2 Replies
View Related
Dec 6, 2012
I have two 3825's. Each has it's own ISP connection. Nat is configued for both. They have an ethernet connection between them and I'm running OSPF between the two so the routes propogate. I have qty 11 Dialer interfaces configured on each router (each router has an exact copy of the other routers dialer interface). However, I only want the Dialers up if the ISP connection on the mated router goes down. Much like HSRP I need one to preempt and be active if both ISP connections are up. When one goes down the other Dialers must come up. Each dialer sends a Dynamic DNS host name and IP address pair to DynDNS.org. So I cannot have both up otherwise the DNS names will bounce between ISP#1's IP address and ISP#2's IP address (back and forth). Let me know if any option exists to make this happen. As an aside the ISP's are providing me DHCP addresses so I cannot work off of an IP, it has to be the physical interface (i.e. Gi0/0).
View 1 Replies
View Related
Sep 11, 2011
I have the below configurations done on a 2900 router. [code]I would like to know, if the IP address assigned to dialer1 interface "20.1.2.133" would be listed in "show arp" ?, as it failed to list on our router and I want to know if this is an expected behavior ?
Secondly, does self ping 20.1.2.133 (dialer interface IP) work ? [code]
View 2 Replies
View Related
May 7, 2012
Is it possible to establish a interface dialer on a layar 3 switch?Or is it only interface for routers?I have a c3750 switch (WS-C3750G-24T), and when i try to establish a dialer interface i get an error message:
[code]...
View 2 Replies
View Related
May 19, 2013
i am having cisco 881 router i want to know whether i can configure dialer interface with username and password for my dsl internet connection.
View 2 Replies
View Related
Jan 6, 2011
I am having an issue with Cisco 1812j Router.
I have 2 1812j router. One router I accidentally lost the password so I reset the password as following link. [URL]
After that I could not submit "dialer" command. Like this.
c1812j-01(config)#int bri0c1812j-01(config-if)#d?dampening default delay descriptiondot1q dot1x down-when-looped dxi
c1812j-01(config-if)#
There is no choice to use "dialer" command.
The other Router is as below which looks ok.
c1812j-02(config)#int bri0c1812j-02(config-if)#d?dampening default delay descriptiondialer dialer-group dot1q dot1xdown-when-looped dxi
I guess I did something wrong to reset the unit.
View 8 Replies
View Related
Sep 7, 2011
I am trying to copy a setup from a Nortel IAX100 where the carrier provides two ATM PVC's over ADSL - one for voice (VoIP) and one for data (IP). Relevant lines from the backup of the IAX's configuration include the following for the PPP authentication over the voice circuit:
<wan_8_32>
<entry1 vccId="1" conId="1" name="Voice" protocol="PPPOE" encap="LLC" firewall="enable" nat="enable" igmp="disable" vlanId="-1" service="enable" instanceId="1509949441"/>
</wan_8_32>
<pppsrv_8_32>
<ppp_conId1 userName="" password="" serviceName="" idleTimeout="0" ipExt="disable" auth="auto" useStaticIpAddr="0" localIpAddr="255.255.255.255" />
</pppsrv_8_32>
The null username and password for the PPP connection have me a bit stumped. Does the PPP connection not use any authenetication at all? (Is that possible/likely? How could I deubg it?) Or does does the IAX100 supply a chap/pap response with null credentails? (If so, how would I duplicate that using an instruction to a dialer interface?I am configuring an 877 with 12.4T and advanced IP services.
View 11 Replies
View Related
Aug 28, 2012
To do this I’ve created another Dialer and re-assigned the atm interface (atm0/0/0) to it. Then I’ve done a shut and then a no shut a min or two later. To my surprise the debug ppp negotiation showed the user name from Dialer1 and then the line was back in my multi link bundle.
My relevant Config is below:
interface ATM0/0/0
no ip address
[Code]......
View 1 Replies
View Related
Aug 17, 2011
I have found this workable cisco 1841 config on the NET. From this link: [URL]
But it is doing source NAT from FA0/1 to Fa0/0. If we need to bridge, is it need to use “ip unnumbered”?
See my config below” 1841 config for Unifi, with ip unnumbered“, can work?
1841 config for Unifi, with NAT
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
! !
! Works perfectly on Cisco 1841, IOS v12.4(24)T !
[Code]....
View 1 Replies
View Related
Sep 7, 2012
We have a dsl connection on 897 dsl router at the customers HO.The telephone line is directly connected to router we configured dialer with username and password and it takes a static ip of 212.249.213.xxx.Now he has some branches that are connected through wireless links and he has arranged for a subnet of 8 public IP's in the range 72.70.245.xxx
Can we some how use these public ip's as secondary in the routers dialer interface and assign to the servers in the branches so that it can be accessed through web.
View 1 Replies
View Related
Nov 29, 2012
We are a new call center company and want to configure the network to setup the predictive dialer, work properly.how a network could be setup to configure predictive dialer.
View 2 Replies
View Related
Feb 27, 2011
We are trying to take ADSL interface into another VRF i.e (ip vrf forwarding VRF2 under dialer interface), the ip address negotiated command disappears, and although the dialer interface becomes up-up state, the adsl interface does not get an IP address dynamically.
Tried:
1) to reenter ip address negotiated again after changing the vrf of the interface, still the dialer interface shows "no ip address" under configuration
2) ppp ipcp accept-address again does not work.
the IOS version:c880data-universalk9-mz.151-2.T1.bin
View 1 Replies
View Related
Jul 11, 2011
I have a NETGEAR Wireless-N 150 Router WNR1000 v2. I am trying to configure it for my LAN which has a DIALER. [code] I tried to configure my NG but it is unable to connect to the network on its own. I have to use CONNECT dialer from my PC to connect which is useless because I can't use my wi-fi enabled devices to access network.
View 1 Replies
View Related
Jan 3, 2012
I have a cisco 870 router which I'm trying to connect to my ISP all the interfaces are in a up, up state. But I'm unable to ping any IP address on the internet. When I do a debug ppp I can see that the username and password are correct with the dialer 1 interface as there is no errors and I can see success. But when I shutdown the atm0 interface and then do a no shutdown I see a message called authentication failed.How does the atm0 interface work with the dialer,Also I spoke to the ISP and they can't see any connection being made but the debug shows success. I also get a default gateway via the ISP but it is the incorrect default gateway as I can't ping the internet and the ISP confirms that the default gateway is incorrect.
View 33 Replies
View Related
Jul 11, 2012
I have a big problem with my Cisco 1841 and the WIC-1AM-V2 in Slot 0.I got the task, to test if it is possible, to build up a connection (Dial on Demand Routing) to a remote modem, which is connected to a console port of another Cisco 1841, with the integrated modem card over POTS from the CLI of the router. My router will only dial out to the remote modems and only if its needed.I am connected to the router with the integrated modem card over a console cable on the console port. The remote modem is also connected to the console port of the remote Cisco 1841.
I found out, with my Dialer Profile configuration, it is possible to build up a connection. I configured a dialer list, that specifies that all ip traffic is permitted an interesting for my dialer interface. So a telnet or ping brings up my dialer, which brings up my Async interface. With the "show line" command, I can see that the TTY line, connected with the Async0/0/0 Interface is in use for 5 minutes, because of the "exec-timeout 5 0", which is configured on the remote router. Now the problem is, in this 5 minutes, I can not use a remote telnet on this line with my loopback interface, because the line is already in use and I get a "connection refused". The first telnet I use runs in a timeout, because the remote host is not responding. When I dial out directly from the modem card and not from the CLI with the AT-commands, I get also the connection and with a return i get the login prompt. I will post my actual config, so that you can see maybe a mistake I did or which command I must use, to get a working connection. [code]
View 6 Replies
View Related
Mar 9, 2011
I want to configure my router to use 2 ADSL lines each with a dialer and a modem in RFC2684 mode. I have a 2821 (IOS 12.4) with an HWIC-4ESW.
My network topology is like this :
ADSL Modem 1 (RFC2684) --
(Fa0/0/0)
Router -- (Gi0/1) MyLAN
(Fa0/0/1)
ADSL Modem 2 (RFC2684) --/
1. I configure my DSL Modem in RFC 2684. The first use 172.16.0.2/29 and the second 172.16.0.3/29. I connect this devices to Fa0/0/0 and Fa0/0/1.
2. I configure Vlan1 to use the network configured on my modem :
interface Vlan1
ip address 172.16.0.1 255.255.255.248
3. I try to ping my devices :
#ping 172.16.0.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.3, timeout is 2 seconds:
!!!!!
[code]....
View 3 Replies
View Related
Sep 4, 2012
Can mac address replace ip (yes or no)
View 1 Replies
View Related
May 14, 2011
I have a small network (10 computers) with 1 SBS 2003 domain controller.There are 3 cables plugged into the Cisco PIX...
>One ethernet cable to our switch
>One console cable plugged into our server
>And of course the power cable
I need to , but I noticed something I've never seen before.... When I unplug the CONSOLE cable our Internet shuts off.I would expect that of the ethernet cable, but not of a console cable.I'm an experienced network tech, but not a Cisco guy. Am I missing something? Is this type setup typical of a Pix?
View 3 Replies
View Related
Nov 12, 2011
How to replace fan incisco 2811 router in live or down condition?
View 2 Replies
View Related
Jun 23, 2012
I think that my rommon image has become corrupt as it will not take a new IOS image. I have tried several images that are within the recommended size and work with another 2620 with exactly the same specification also some commands that are available are not recognised when typed
View 7 Replies
View Related
Feb 3, 2011
I have MGX 8850 (PXM45/AXSM) and I want replace My faulty hard disk 40Gbps (4200RPM) whith other hard disk 80Gbps (5200RPM).Is it possible or No?
View 1 Replies
View Related
Feb 10, 2012
Can I replace my AT&T 2 Wire with any DSL Modem? We get terrible wireless response in rooms not close to the modem, I don't care what the additional cost is, I just want to use my laptop throughout the house, including my basement.
View 4 Replies
View Related
Mar 6, 2013
I am attempting to replace an existing printer on the network and keep running into trouble. I am sure at this point it is my frustration with it that is not allowing me to see what I am doing wrong. I attempt to just swap it out with exsiting printer and it grabs an IP address and then when I try to enter that IP address into my broswer to access the printer to give it the permanent one from printer I am replacing I cannot get to the printer.
View 6 Replies
View Related
Nov 9, 2012
My home router is an aging D-Link DGL-4100 and I am looking to replace it.My max budget is ~$250 USD.
I use 2 Ubiquiti Unifi UAP-Pro APs in my home for WIFI access, so I have the WIFI aspect of my home network covered completely. All wiring in my home is either Cat5e or Cat6, my switch is a gigabit HP ProCurve 1810G-24, and my cable modem is a Motorola SB6120 (Comcast cable broadband). I have 7 IP cameras (security system), 4 streaming media players, several PCs, a server, and several other network connected devices. I am the only resident.
I am looking to maximize my WAN to LAN (& LAN to WAN) throughput while maintaining a very secure network. I also want the router to have reliable VPN. If it is a wireless router, I would most likely not utilize the WIFI feature, probably turning off the WIFI radios and just use the router functionality.
I don't have the time/patience to build a PFSense (or similar) box and learn the software, so am only considering an off-the-shelf solution. Yes I know that PFSense and Untangle are great, I simply don't have time to learn them presently or in the foreseeable future.So, which router for wired performance and security would you recommend?
View 2 Replies
View Related
Jan 15, 2012
What is the new configuration in ASA 8.4 to replace the old "nat 0" command.
View 1 Replies
View Related
Mar 25, 2012
We use a 3825 router to screen alot of the junk from the internet side or our firewall. Its worked well for the last 4 years buthas rebooted multiple times in the last month for no apparent reason.At this point I think I would prefer to replace it.Our current internet link is 100Mbps and this router handles that quite well. Is there an equivalent that I should replace it with, or should I just buy another 3825 ?One with an OOB management port would be nice.
View 6 Replies
View Related
Jul 19, 2011
Our one of the Client need to replace CISCO 831 router with high end router , there will be around 60 to 70 users accessing this router for Internet surfing. Right now 831 having 3 Ethernet and 4 Fast Ethernet Ports.
View 4 Replies
View Related
May 15, 2012
I need to upgrade/ replace a Cisco 515 E firewall with a Cisco ASA. Not sure what model yet! The pix has about 80 lines of ACLs and I side and outside interfaces with No VPNs.. I was wondering of those lines of ACLs can be transferred over to ASA as is or there are things I need to watch for ?
View 21 Replies
View Related
