providing the GPL sources for the DIR-615 rev.C firmware. However, it is incomplete!The bootloader used by the device is U-Boot, which is also licensed under the terms of the GPL. Sadly these parts are missing from the source code package provided by D-Link.
View 5 Replies
I have a wave spot controller. That is connected to my PC(Fedora 14). In Shell I'm < arp -n > then I'm getting "Incomplete" in the place of Hardware Address.
View 1 Replies View RelatedI have a 3750X set up with a number of VLANs and have connected a WLC5500 to this. I've assigned the port on the switch to the correct VLAN, given the WLC a management address on that VLAN and it has the correct gateway. I can ping to this gateway from other devices, but not from the WLC and can't ping or browse to the management address of the WLC (I can browse to it when plugged directly into the SP).
When checking the switch arp table, it shows the IP entry of the WLC as INCOMPLETE yet show cdp nei detail shows the device on the correct IP and all the device details. I have changed the port on the switch, the port on the WLC, the cable and the GBIC, cleared the arp and rebooted all devices and it hasn't made any difference. On the switch, I tried assigning the burned-in MAC to that IP statically but it didn't work - does each port have an individual MAC?
've used every version of ie up to 7 with no real problems, but I figured it had to be the browser, so I switched to Firefox. No improvement!Problems:When downloading (WinXP PC) online, suddenly all zips and apps (even Flash Player for browser) started showing "incomplete" or as it's called "Corrupt" files. One or two or maybe more small files would be left out. When finished downloading, it would say it completed the right mb's, but when unzipping or trying to install, there would be files missing. Tried "Repair" in WinRAR, no luck.
View 7 Replies View RelatedI recently purchased the Magnavox MBP5130/F7 Blue-Ray player. I have been trying to get the player to connect to my wireless network so that I can stream Netflix, etc. I am using a Linksys router. The device "sees" the wireless network (it displays the name) but I seem to get the error that the Wireless Router settings are incomplete - use advance settings to complete setup. In advance settings it fails - it is not possible to connect to the DNS server. Please confirm the internet connection or DNS address setting. IP Address 192.168.0.102;
View 14 Replies View RelatedI've just discovered that my wireless router is not secure (WRT54GS v5). In trying to set up the propoer security, the set up screen appears as incomplete (after entering 192.168.1.1). It only shows 3 tabs at the top - Basic Setup, MAC Address Clone, and Advanced Routing. No tab to deal with the settings. I have tried resetting the router and plug/unplug several times. Triued entering thru IE and Firefox.Is there another way to set up the security on my router or at least get the proper screen?
View 4 Replies View RelatedI plugged an IP device into a 2960 Catalyst switch. The port is up, but there is no MAC address learned on it:
TNSWAGCS01002(config-if)#do sh mac add int fa0/16
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
TNSWAGCS01002(config-if)#
TNSWAGCS01002(config-if)#do sh int fa0/16
FastEthernet0/16 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0064.40ee.f510 (bia 0064.40ee.f510)
Description: --- STC ---
[code]....
I read that it may be a L1/L2 issue. We tried with another ethernet cable. We also tried with another IP device of the same model. That did not solve the issue.
The bootloader used by the device is U-Boot, which is also licensed under the terms of the GPL. Sadly these parts are missing from the source code package provided by D-Link. Therefore I am asking you to add the U-Boot sources to the provided archive or post them here in the forum.
View 12 Replies View Relatedmy researvation table is incomplete. Below I show ipconfig that shows wired & wireless NICs assigned ip addresses by the E3200 router but the DHCP table only shows one.
I need to reserve the ip address of the wired address but can't get at it.
I've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.
View 2 Replies View RelatedI Want To Boot PC From LAN.
View 2 Replies View Relatedwant to boot my network how can i do that?
View 1 Replies View RelatedI have a netbook, so it have not dvd drive. I haved usb flash drive, but now it not work. I want to install windows on my netbook, but i cant as there are no dvd drive and flash drive.But i have a PC computer, which have dvd drive.I want to know, that is it possible to boot my PC's dvd rom and install windows on my netbook.
View 14 Replies View RelatedWe have got a big problem with our NAM (WS-SVC-NAM-1) - it does not boot. We have got a second one and in an other chassis. I changed the chassis, and RAM and Flash from the other one. RAM and Flash are ok.
We checked the disc (hardware) with an Ontrack-tool -it is OK.
environment: 6500 VSS
sh logging:
Jun 17 13:18:24: SW1_SP: Switch 1 Physical Slot 7 - Module Type LINE_CARD inserted
sm(cygnus_oir_bay slot7), running yes, state wait_til_online
Last transition recorded: (offline)-> empty (remove)-> empty_clr_persist (remove)-> empty (insert)-> may_be_occupied (timer)-> occupied (known)-> can_power_on (yes_power)-> powered_on (real_power_on)-> check_power_on (timer)-> check_power_on (power_on_ok)-> wait_til_online
is it possible to boot the image from a usb stick on a 1812? if so, what are the requirements?
View 14 Replies View RelatedI've got a Cisco 2621 with this IOS image in flash: c2600-i-mz.120-7.bin (the only IOS in flash). When I power up the router, the following errors occur:
open: file "n" not found
open(): Open Error = -1
loadprog: error - fileopen
boot: cannot load "flash:n"
I have to press "Ctr l" and "break" to enter Roman, there i can use the boot command to start the IOS. Configuration register is set to 0x2102, all running config should be factory default.
What I have to do to boot the IOS directly when i power up my router (without entering Roman mode...)?
I've got a fully working 877w that I'm trying to get to boot from tftp, but I just can't seem to get that going.I have a tftp server running and can copy images back and forth without any trouble.I have this in my config:boot-start-markerboot system tftp c870-advipservicesk9-mz.124-24.T2.bin 192.168.1.200boot-end-markerDuring the boot process I get an error message that says there is a missing or illegal ip but I really don't see how that can be as my tftp server is 192.168.1.200 just like my config says.
View 16 Replies View RelatedXP slow boot for network connections When start PC it goes normal and quickly until comes to network icons in the right low window. It takes 5 minutes for network icons to show up.
View 2 Replies View RelatedI am looking into setting up a home network for file sharing and backups. something I was wondering is can I install an operating system on the server computer and boot from it on multiple computers on my network? there are 2 unidentical desktop PC's and 2 laptops in my house I know alot about computer hardware and i am confident with individual computers but i have never used a home network before. in my bios there is a boot from network option. if i could i would use windows 7 professional as i am very familiar with it.
View 3 Replies View RelatedMy PC doesn't connect to internet on initial boot, says there is a disconnected cable. On a restart it finds the wirelss card and connects no problem to our BT hub. Tried disabling the wired option, tried a number of things around repairing links etc. but nothing works. it is annoying. PC spec below. Windows 7 is the OS
Giga byte mother board GA-Z68P-DS3
4x4gb of RAM
Intel i5 3.2 CPU
Radeon HD 6770 Graphics card
A wireless adapter TL-WN350GD
A 120 GB SSD hard drive
And a 1TB hard drive
A CnM card reader
Optical DVD drive too
I have purchased a new hard disk, but my DVD ROM is dead. i have one another system. How can i boot the new hard disk from network..?
View 1 Replies View RelatedI would like to know how i can boot other users off of the wifi network temporarily. How can i do this? Ive tried adding their mac address to the router admin, not sure if ive done it correct though, its a dlink login.Failing that is there any programs that can do this?? Ive come across one called wifijam but its only available for mac.
View 1 Replies View RelatedI have build a new pc this week. All was fine offline. After connecting to the Internet initially everything loads quickly however sometimes after turning on my pc or restarting it the Internet just refuses to load. Pages take forever then I get a message unable to connect however the connection is still active and all my other devices work ipad etc. after a few times restarting or leaving it for a while all is fine.
View 1 Replies View RelatedI've had a Belkin N+ wireless router for about 5 months. I reset the router recently (using the reset option on the router itself) and now it doesn't boot up. The lights at the front flash as if its going through its boot sequence but it never stops. I left it for 2 hours while I went out and when I came back it was still going through the boot sequence.
View 3 Replies View RelatedI am running Windows XP and Linux Ubuntu on dual boot.When I open into XP I cannot establish an ADSL internet connection, but can by wireless.If I open into Ubuntu I can establish both ADSL and Wireless internet.In Windows I have checked my Realtek Card in Device Manager - says working O.K.. When I try to open internet by ADSL the message is " trying to assign IP address " then limited or no connectivity" - if I try "Repair" message cannot establish IP address.Clearly something is blocking my connection.
View 17 Replies View RelatedI have wlc AIR-CT2504-K9. After save config and power down, wlc cannot start. In console I see:
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ163201YR, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz da ta rate)
CPU Cores: 4
[Code].....
i'm trying to re-image an asc se 1113 with a recovery cd but i keep getting a disk error complaining of an invalid destination drive
View 1 Replies View RelatedI have been trying to upgrade my WLC 2106, but it is stuck at rommon/grub mode.The steps are as follows
rommon #5> tftpdnldROMMON Variable Settings: ADDRESS=192.168.100.1 SERVER=192.168.100.10 GATEWAY=192.168.100.10 PORT=Ethernet0/0 VLAN=untagged IMAGE=AIR-WLC2100-K9-6-0-196-0.aes CONFIG=
[Code].....
I'm having an issue, with an WS-SVC-FWM-1-K9.
The card doesn't boot properly, it tries to boot, but after a while the 6500 puts it in shutdown.
I've noticed that it has 2 RJ45 ports in the board, I've plugged my console cable, but i only get characters with the default serial configuration.
Any information about the port configurations? Is the port "PC Console" the correct one?
My ASA5505 is not boot up. I did upload ios from rommon mode with tftp and tftpdnld.It is uploaded successfully after reboot it stopped at cisco logo sing.
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
I deleted old ios and upload new but look same.
My AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
I have two 877's that have both reset with the following messages on boot, and dir of flash and lost+found/It appears that there is a IOS on the flash? but rommon doesn't know where it is. I tried to "set" with no luck as set is read.
I have noticed that the IOS is 0 size. [code]
I have added a new NME-WAE-502-K9 in one of our remote Cisco 2811 routers. This module doesn´t boot, and it seems to be in a loop trying to boot. [code]
View 6 Replies View Related
