I've had a Belkin N+ wireless router for about 5 months. I reset the router recently (using the reset option on the router itself) and now it doesn't boot up. The lights at the front flash as if its going through its boot sequence but it never stops. I left it for 2 hours while I went out and when I came back it was still going through the boot sequence.
View 3 Replies
We have owned a this router for nearly a year now, and recently it has been acting up.Today I added a static connection or something of the like for my Xbox, with the correct ip gateway and subnet mask. Since the restart it has never stopped cycling the boot sequence without end. The download lights cycle and the router light flashes constantly. And I am unable to connect to the router page at 192.168.2.1 So I cannot reset the router, the hardware reset button just momentarily pauses the endless booting process.
View 4 Replies View RelatedI just bought a N750 DB router. On boot up, the 5Ghz side will show up for about 20-30 seconds and then it just "disappears". I was even able to connect to it @ 300mb with my laptop. The 2.4Ghz shows up just fine.
View 3 Replies View RelatedI have an Acer Aspire 5517 with Windows 7 Home Premium connected wirelessly to a Linksys E1000 which is connected to a surfboard modem connected to Comcast cable internet. I just picked up an HP Proliant DL360 server with no OS and no optical drive. It tries to PXE network boot when I turn it on. How do I use my Laptop to install a linux image via the network?I have read extensively about this subject for a couple of days now and jacked up my IP settings in my router as well as my network adapter a couple of times now. Everything is backed up and my original settings are written down. I have asked for advice from Microsoft and HP as well.
View 1 Replies View RelatedI have a problem with 1841 router - It wont't boot up and there is a message
Correcting primary nv_flash
I have a 2 computers connected to a Linksys BEFSR41 router which is connected to a Verizon Westell DSL/Cable modem. From time to time the Ethernet link between the modem and the router spontaneously disconnects. I can reconnect the link by going to the setup menu on the router with a browser @ 192.168.1.1 Sometimes I have to do an ipconfig/release and renew to fix the link. Sometimes I have to power cycle the PC and the modem and the router.Currently this disconnect problem has gotten much worse. It occurs about every 15-20 minutes while I'm connected to the net. It also occurs when either computer is booted or turned off (I see the link light on both the modem and the router flash red for a moment).
View 10 Replies View RelatedI have a 2621 router, because I want an image of about 21M, I upgraded as follows:
IOS = 32M
RAM = 64M
ROM VERSION = 12.2
However, when I power up my router, it goes into a boot loop, and I see the following messages:
NOT ENOUGH MEMORY IN THE SYSTEM TO RUN THIS IMAGE
***SYSTEM RECEIVED A SOFTWARE FORCED CRASH***
how to overcome this error, and successfully upgrade, so I could load my new image?
I recently obtained a 2851 and have been battling this issue for a week now. An odd set of circumstances happen with the bootstrap startup process. If the router has loss of power or when reloaded; it fails to read the CF card and boots to rommon. I can tftp an image to it (tftpdnld -r) and IOS CAN read the flash card along with any saved configuration.In fact once in IOS, I can wr mem and print the hardware details of the CF card. Once I reload the router it goes to rommon, fails to open the flash, then sits until i tftp the image back. When the router load IOS, it also loads the startup config.I don't think it's a problem with the CF card as IOS can read it. I've tried formatting the card from IOS and from my pc as FAT, FAT16, FAT32, and NTFS - it didn't make a different. I updated the ROMMON to allow for USB booting but haven't purchased a USB Drive yet for testing. The upgrade didn't resolve this issue either. It almost seems like a firmware problem with the EPROM.
View 7 Replies View RelatedCisco router 3945 when unpacked from the box and powered on , it was not able to find boot loader image and booted in ROMMON mode. tried to boot from the external flash and tftp but still not able to.
We replaced router chassis 2 times and both the times faced the same problem.
Getting message, cannot open "flash:" on 1841 evdo router, how do I reinstall flash? I am currently consoled into the router, the prompt is coming up as rommon 1>
View 1 Replies View RelatedI've got a 2621XM that has not been used for a while.Completely stripped of any modules and configuration files, the router will continually cycle the startup process without actually booting from the IOS.
The cycle displays the following :
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10034ec
What I've tried:
1) Downloading another IOS image (c2600-is-mz.123-20.bin) via Xmodem and running "confreg 0x2102" from the rommon. All that did is change the last message to "program load complete, entry point: 0x80008000, size: 0x10fa95c"
2) Running the command "boot flash:c2600-is-mz.123-20.bin". If I enable the diagnostics via rommon, the cycle expands to:
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10fa95c
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
[code]....
If it wasn't for the lack of error messages, I would assume it was a hardware issue.If the image was corrupted, I would expect a message indicating that the image couldn't be read.
When I look at the local area connection the status is acquiring network address and just sits there. When I try to repair, it states that windows couldn't finishing repairing because it can't renew my IP address.
View 7 Replies View RelatedLast night we had some pretty bad lightning and thunder and our Linksys WAG160N appears to have had a bit of a fright.As I was going round unplugging items in case of a hit (this was after a flash or two, relatively nearby), all the lights on the router were off except for the ethernet light (plugged into a Linksys homeplug adaptor). Now the router doesn't appear to boot. When powered on, the power light doesn't flash or anything to indicate booting up, all you get is the ethernet light (if connected) after a few seconds, but no activity. I'm presuming something has been fried or corrupted? I'm not sure if we did have a power spike either through the mains or phone line as all other equipment seems to be fine, but I'm wondering the the homeplug connection might of had something to do with it after reading a few posts from others on the subject.I've held in the reset button while starting and it doesn't appear to have done anything. I will try the 30/30/30 reset tonight.
View 1 Replies View RelatedI recently received these routers and after the first reboot I changed the user id and password so it does not lock out...After configuring my routers for installation, upon bootup I am getting this message scroll down my screen
monitor: command "
My 851W will not complete the boot up process, here is the output during bootup(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013. Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T14, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Wed 18-Aug-10 02:37 by prod_rel_teamImage text-base: 0x8002007C, data-base: 0x814ECE54This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
View 3 Replies View RelatedI've inherited a 7206VXR router and it takes very long to boot. It outputs READonly ROMMON initialized to the console and 14 minutes later it continues the boot process. After 17+ minutes the boot is complete with the correct full image. The processing engine I have is the NPE-G1 and I'm looking for an upgradeable ROMMON image or a reason why the boot is taking this long.
View 1 Replies View RelatedWhat would happen if I installed a 32MB (MEM870-32F=) flash upgrade card in to a Cisco 871 router that already had 28MB flash on-board already? Would the router boot seeing 52MB (the max this router can have) or would it fail completely since the combined total would be over 52MB?
I know you can get a 24MB upgrade card but they are quite expensive.
How do I upgrade the boot rom version on the 7200 router? I am running IOS Version 12.4(22)T and when I plug in the serial ds3 card in my router it keeps rebooting with a watch dog error ( see below). Also, what version should I upgrade to?
Router#sh verCisco IOS Software, 7200 Software (C7200-SPSERVICESK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Fri 10-Oct-08 10:10 by prod_rel_team
ROM: System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(13)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Router uptime is 0 minutesSystem returned to ROM by power-onSystem image file is "sup-slot0:/c7200-spservicesk9-mz.124-22.T.bin"
[code]....
I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies View RelatedI have wlc AIR-CT2504-K9. After save config and power down, wlc cannot start. In console I see:
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ163201YR, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz da ta rate)
CPU Cores: 4
[Code].....
I have been trying to upgrade my WLC 2106, but it is stuck at rommon/grub mode.The steps are as follows
rommon #5> tftpdnldROMMON Variable Settings: ADDRESS=192.168.100.1 SERVER=192.168.100.10 GATEWAY=192.168.100.10 PORT=Ethernet0/0 VLAN=untagged IMAGE=AIR-WLC2100-K9-6-0-196-0.aes CONFIG=
[Code].....
My AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
I lost the WEP key for my Belkin N+ wireless router.I bought a new wireless printer and cannot connect it through the router without the WEP key.How can I get the WEP key #.
View 1 Replies View RelatedI'm on talktalk and have been for a few years. They supplied me with a speedtouch 330 modem which has worked brilliantly, but now i am wanting to set up a router so i can connect to xbox live. I have a Belkin ADSl modem with wireless G router which i have tried to set up a number of times without success. I am trying to set the router up so that it has an ethernet connection to the computer and another ethernet connection to the xbox but i can't set the router up with the internet at all. To start with i am trying to set just the pc up. On the router, the power light is on, the ethernet port light is on, as is the wireless and the phone line one, but the internet light isn't on at all.
View 4 Replies View Relatedmy Belkin routers wireless wont work. I tried unplugging it, resetting it, but nothing working. Ethernet is working fine, but I need wireless back ASAP.
View 1 Replies View RelatedI have had this same problem. When I clicked to connect on the wireless router with a new computer, instead of asking for the password (as most routers would) it asks for the PIN. The it takes me through to a strange page where it asks me to enter the name of the network and suggests the name of my computer as the name of the network. Once I chose a name it then connected locally buy not to the Internet and then disconnected my other computer from the Internet too. I tried thecomputerguy's suggestion but when I click on Wi-Fi Protected Set Up" it asks me for a password before I can access custom settings. It then won't accept the router password i had originally created, the pin or any of the other codes on the bottom of the router.It was weird-almost as if entering the router pin from my new computer overwrite the previous settings. The router has an installation cd which I didn't use when trying to connect the new computer-not sure if this has caused the problem?
View 1 Replies View RelatedWe are setting up one of these for the first time. It is in a constant rebooting process.
Here is the boot process:
r WRDTR,CLKTR: 0x8200083f 0x40000000
r RQDC ,RFDC : 0x80000032 0x00000211
using eeprom values
[Code].....
I tried to upgrade the cisco boorloader pf WLC 4402 from version 4 to 7.2. I updated ER.Aes FOR 7.2 (EARLY RELEASE.aes). It was updated perfectly and then I rebooted controller....now i can only see blank screen from connected console.I tried the flash of other lan controller but its not working because the issue is in the ROM as the boadloader file is in the ROM which is corrupted now i want the solution to upgrade the boatloader file inside the ROM.
View 1 Replies View RelatedI've been configuring hundreds of 3602i APs via Prime without incident, but I've encountered 2 APs that get to the ap: prompt and doesn't proceed further. If I type boot, then they'll complete the boot process.
How do I configure these 2 APs so they will automatically boot fully?
i have 1262 LAP which is fail to boot and went to rommon mode
here are the logs
ap: boot
Loading ""...: permission denied
Error loading ""
[Code].....
I've got a Belkin G wireless router.I've got my Vaio with windows 7 , my other emachines with vista and another acer laptop in the house also on vista/All laptops can connect to the router and internet fine but when I password protect the WI-FI the ACER aspire won't connect to the router, while the other 2 and also a ps3 all connect with the password no problems.
View 1 Replies View RelatedMy computer crashed the other day and HDD failed. i finally got it back up and running but ive been using a usb wireless adapter. i do not have the disk anymore to install the drivers, nor will my computer install them from the internet because i dont have an internet connection on my desktop. what are my options to have them installed?
View 3 Replies View RelatedI have a Belkin wireless router attached to my computer. It was set up as an access point, with an IP address of 192.168.0.254. I had some problems with the network today and could not access this unit by typing in the IP in my browser. I feel certain that is the IP address I put in it when setting it up, as I have a record I kept of all the settings. Is there a way to retrieve the IP address to verify that is what it is set to?
View 3 Replies View Related
