Cisco WAN :: 851W Router Will Not Complete Boot Process
May 16, 2011
My 851W will not complete the boot up process, here is the output during bootup(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013. Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T14, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Wed 18-Aug-10 02:37 by prod_rel_teamImage text-base: 0x8002007C, data-base: 0x814ECE54This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
View 3 Replies
ADVERTISEMENT
May 8, 2011
I have a problem getting my ASA 5520 boot properly. I first though of a flash problem and did a flash erase in ROMMON, then it brought error 15 during boot (No images found in / Error 15: File not found). I then TFTPied and image from Rommon, when done loading the image and start booting, the system hangs and nothing else. Attached is the screen I got on my console during boot up. BTW, the system was in the same state before I undertook any of the above actions. I don't have a service contract, so I can't contact TAC.
View 3 Replies
View Related
Mar 19, 2013
document which explians normal booting sequence in a 6500 Switch running IOS. What I am looking for is in which order the image is loaded in SUP, RP, SP etc
View 1 Replies
View Related
May 2, 2013
why my AIR-AP1262N-A-K9 will not boot all the way. It will get all the way to initiating the interfaces and stop. I can never get to controlling the cli. This is my first time with a cisco ap but from everything that I read it seamed very easy.
This unit from what I understand will work all on its own with no controller. Hence it is called a "standalone" model. Yet it seems to be looking for something to finish during the boot. Below is the out put during boot. The last line is where it stops.
r WRDTR,CLKTR: 0x8200083f 0x40000000r RQDC ,RFDC : 0x80000033 0x00000212
using eeprom values
WRDTR,CLKTR: 0x8200083f 0x40000000RQDC ,RFDC : 0x80000033 0x00000212
[Code]......
View 7 Replies
View Related
Mar 15, 2012
According to the documentation, I'm supposed to be hitting the Esc key when I see the Loading "flash:/[imagename]" ####### ... line, but this doesn't seem to be working. I've tried hitting the Esc key a lot during those lines, holding it down, hitting it early, hitting it late, hitting it in the middle, and still no joy.
I'm trying to break into a handful of malfunctioning 1242AG APs to see if I can get them working, or if they're faulting hardware that's beyond repair. (So far they're all coming back with: no "IP_ADDR" variable set, so how to set that without breaking out of the boot cycle).
View 4 Replies
View Related
Oct 24, 2012
I am very new to using the CISCO IOS. Here is the situation: I have a CISCO 851W router in the garage that I want to connect to my Linksys router in the office, which is connected to the internet. The 851W is connected from it's WAN port to Lan port 1 of the Linksys router. Now, currently that ethernet cable is a straight-through cable. Does it have to be crossover? If so, I can fix that.So I have no idea how to give the 851W internet access I am a total CISCO noob. I will leave it to you guys to recommend what IP to assign the router and subnet.
View 9 Replies
View Related
Apr 30, 2013
i want to enable a port 7000 and 514 on my cisco 851w router. using the command-line?
View 1 Replies
View Related
Oct 9, 2012
I have two core switches - 4506E, and i noticed there are frequent cpu spikes on both of the cores switches. As its spikes intermitendly i couldnt able to anlyze the issue. I need inputs on the following,
1) Is there any Free CPU process monitoring tools to identify which process is spiking ?
2) Troubleshooting techniques to identify the issue.
View 1 Replies
View Related
Oct 25, 2012
I have a CISCO 851W router in the garage that I want to connect to my Linksys router in the office, which is connected to the internet.The 851W is connected from it's WAN port to Lan port 1 of the Linksys router. Now, currently that ethernet cable is a straight-through cable. Does it have to be crossover? If so, I can fix that.
I want the default gateway for the CISCO router to be 192.168.2.1. I am not sure how to configure that. [URL]
View 3 Replies
View Related
Dec 25, 2012
EA6500 5GHz band only four channels (36,40,44,48), the lack of 149,153,157,161 channel, firmware Ver.1.1.28.146072, how to add 149,153,157,161 channels?
View 3 Replies
View Related
Apr 6, 2009
I have finally been able to reconfigure my BEFSR41 V3 Wired Router to properly support my small server environment. I would like to know if there is a way to make a complete Backup of the current configuration that should be restored to the router if it should become "reset" to factory defaults. This happened to me approximately a week ago, and it took several days, a couple of phone support calls, and quite a bit of"grief" and aggravation/frustration before I managed to get everything re-configured correctly. If it had been "Backed up" to a file, I could have restored it and been back up and serving websites in a few hours. Instead it took almost a complete week! Is it even possible to actually backup the router? Or... must I just print each screen to be sure I get it all?
View 4 Replies
View Related
Jan 14, 2012
I bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the QuickVPN Clien for connecting to my home network.My home network is connected to a pre provide by my ISP Thomson and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analysing the log you can see that I can get any PING to complete the VPN connection. [code]
View 1 Replies
View Related
Dec 14, 2012
EA6500 5GHz band only four channels (36,40,44,48), the lack of 149,153,157,161 channel, firmware Ver.1.1.28.146072,how to add 149,153,157,161 channels.
View 3 Replies
View Related
Oct 2, 2011
I have two PCs connected to each other through a Wireless-N Gigabit Router (WRT310N). One PC is running Windws XP while the other is running Windows 7. At this point I do not have, or want, Internet connectivity. I would, however, like to call web pages on the Windows 7 PC from the Windows XP PC. The Windows 7 PC has php files that run C++ files to analyze files supplied by the Windows XP PC and I would like to send the results of the analysis back to the XP PC.The reason for this is that I am setting up a home based web site that allows users to run programs on my Windows 7 PC but I want to keep hackers from accessing files on my Windows 7 PC. So the XP will be connected directly to the Internet and the Windows 7 PC will only be connected to the XP PC.I can successfully ping both ways between the Windows 7 PC and XP PC. So I fire up FireFox (FF) on the XP PC and type the following in the FF URL box.
[code]....
The same happens when I replace the Windows 7 PC IP address with the Windows 7 PC name.I tried to set up a network between the two PCs with the MS network wizard on the XP box. It made a setup disk with a single file on it. I was supposed to run the setup file on the other PCs that are supposed to be on the network but, whe I did, I got the following message.Cannot complete the Network Setup Wizard,An error occurred during the configuration of the network on this computer.You can configure the network manually.
View 3 Replies
View Related
Jul 27, 2011
I've recently been gifted with a WRT54GS v.2 which came from a family member who upgraded their wireless router and therefore passed this one along to me. It was working perfectly for them, but not me.
I've tried using the setup CD and doing a manual setup, but no internet connection is detected. I must confess to being a total wireless router newbie, this is my first one, so I am stumped as what to do next. I've looked at the FAQ's and through the forum as well, but I just don't know what might apply to my situation and as I am not very well versed in the terminology, I tend to get lost.
View 8 Replies
View Related
Feb 22, 2009
If by mistake I have attempted to upgrade the firmware my router "WRT610N" via my wireless laptop and after 24 hours the same screen "upgrading router" continues displayed and the router does not respond, How do I fix this?
View 9 Replies
View Related
Jan 31, 2011
I have looked up the command sequence for port mirroring and it seems pretty straight forward however in my case the command will not execute.
I have a 851W with 12.4T
If I do: #monitor session 1 source interface fa 4 (wan port)
i get the response invalid input detected however if I do the same command for fa 1, fa ,2 and fa 3 they work
Using the ? shows the valid entries are [0-4] for fastethernet
I just want to monitor WAN traffic with WireShark, particularly DDNS requests, with a spare PC connected to a free lan port.
I would use a hub on the Wan connection but unfortunately I do not have one at the moment.
View 8 Replies
View Related
Feb 1, 2011
I am trying to configure QoS on my Cisco 851w router using the class-map command.However it won't accept the class-map command.The router is running cisco IOS version 12.4(15)T10 "C850-advsecurityk9-mz.124-15.T10.bin".
View 3 Replies
View Related
Feb 3, 2011
I have looked at the Cisco Feature Navigator and according to the output with IOS 12.4(15)T1 thru T13 there is support for multiple SSID's and the feature "Multiple Basic Service Set ID" should be supported.
When I try to invoke that command mbssid on my Dot11 interface I get 'Invalid' response. Am I missing something here? Is the Feature Navigator misleading me or am I doing something wrong?
All I want to do is broadcast both SSID's that I currently have configured. Currently only one guest mode SSID is allowed and broadcast.
View 2 Replies
View Related
Jun 21, 2011
I bought a Cisco 851W router from a coworker about a year ago and tried setting it up at my home with nothing but headaches. I finally gave up and went with DD-WRT and have yet to look back (my $40 router outperforms this thing on so many levels, but I'm getting off-topic!). I recently re-discovered this beast and pulled it out of storage to see if I could get a test network setup at home to practice on. I checked for any IOS updates and downloaded (and installed) the lastest image (c850-advsecurityk9-mz.124-15.T15.bin). I consoled in and verified the initial 10.10.10.1 IP was configured in the VLAN1 interface and directly connected a PC to one of the switchports and pulled a 10.10.10.2 address. I pull up SDM from my browser (I have used FF, IE, and Chrome, all with the same results. Java version is the latest, 6 Update 26.) and it launches the initial configuration wizard. I go through the steps and get up to the DHCP Configuration (after LAN, before Internet/WAN setup) and try to click Next and nothing happens. It doesn't freeze as I can easily go Back, but can never move forward beyond the DHCP configuration. Pressing Cancel on the wizard just shuts down SDM as a whole and exits.
In my troubleshooting steps, I did notice that as soon as I click Next in the DHCP configuration, nothing will happen in the wizard, but the SDM window in the background will automatically present the "Apply Changes" and "Discard Changes" buttons, which weren't there in the previous steps. Of course, neither of those are clickable due to the wizard being open. I really don't want to configure this thing from scratch using the CLI if I don't have to..is there ANY way I can bypass the SDM Wizard at all? Also, I'm running SDM Express, would downloading ASDM and trying to connect from there make any difference?
View 1 Replies
View Related
Feb 11, 2011
I have been trying to get my 851W to work with DDNS for a long while now. In fact I walked away from the problem in frustration and loaded DD Client on a Linux box until I had time to re-visit this. The folks at Zone Edit were not able to offer much with CLI problems.
When I debug DDHS updates I get to a point where the the router tries to resolve the DDNS update address and fails.So I have a number of questions:
a) Is this error the result of lack of DNS server names written to the config?
b) My WAN interface is a DHCP client to my modem. If the DDNS updater does need to resolve a name, shouldn't the DNS server info be provided by the DHCP process for the WAN interface? How do I ensure that name servers are automatically assigned for the DDNS updater to use?
[Code] ........
View 1 Replies
View Related
Mar 22, 2011
I have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. URL We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
View 1 Replies
View Related
Jun 16, 2012
I need to be able to run more than one BGP routing process on my lab router. I have over connected BGP routers connected to my live production network and I need to emulate the production network with GNS3. However, BGP rules only allow a single BGP routing process on a single router. how to overcome this limitation for my lab?
View 9 Replies
View Related
Sep 12, 2012
I have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. [URL] According to our baseline it should not be more than 40% at any given time. We see high CPU uptp 70% consistently.
CPU utilization for five seconds: 99%/0%; one minute: 57%; five minutes: 55%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
442 66173704 90234125 733 96.86% 46.09% 46.30% 0 BGP Router
7 509291060 26330202 19342 1.17% 3.90% 2.99% 0 Check heaps
Router has 1 eBGP session with ISP from where it downloads whole IPv4 internet routing table and two IBGP session with other two rotuer. When I look at BGP summary table I see many updates received from ISP and sent out to IBGP neighbors. Also did debug BGP updates to confirm it.
We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.
%BGP-6-BIGCHUNK: Big chunk pool request 628 for community. Replenishing with malloc
I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
View 5 Replies
View Related
Jul 10, 2011
i have a cisco 2811 series router and using for internet router and is working fine.i disabled its password recovery process from router cli like
NO PASSWORD RECOVERY Process Enable now i forgot its username and password and need to recover its password.
View 2 Replies
View Related
Mar 27, 2011
I plan on replacing my linksys BEFW11S4 wireless router with a new linksys WRT120N wireless router. Should I completely remove and unplug the old router before inserting the startup CD and beginning the installation process for the new router?
View 3 Replies
View Related
Mar 16, 2011
I installed the quickVPN Client for use with RVS4000 small business router/VPN on a platform with Windows 7. It was not able to complete the VPN connection. I installed on Windows XP machine, both on the same network. The XP machine was able to connect just fine.
View 1 Replies
View Related
Dec 11, 2011
We have Comcast cable (I believe) and it comes into a modem. The modem has a line out to an ethernet switch. Coming into the E switch is a line from the Upstairs router (Realtek PCIe GBE).I want MY computer to be completely private from the rest of the family, and be invisible if someone were looking. (I'm mom and I keep my frustration journal on my Microsoft Word). I don't want to use wireless.
So, I bought a Belkin N150 and put it between my computer and the switch, and the internet didn't work at all. However, if I use a line that comes from the Realtek router, it works. I am SO confused! (I found out that if you are hooked to the same router as the others in the house, they just have to be smart enough to configure that router and they can see everything you do on your computer!)
View 6 Replies
View Related
Jan 18, 2012
i have newly installed lms 4.0.1 server, where i get the "device status window" in the troubleshooting section not loaded.most of the items on the page are loading...., but they will never get loaded completely.i have checked all updates and bugfixes for lms and also for solaris.in the daemons.log file i found the following error messages, they are repeated every few minutes:
In EPMOgsAdapter:EPMOgsadapter is sleeping. Waiting for OGSServer to come up com.cisco.nm.xms.ctm.common.CTMException: URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!
17/Jan/2012 12:06:55:307 ERROR ? ? - URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!
17/Jan/2012 12:06:55:320 ERROR ? ? - URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!
17/Jan/2012 12:06:55:321 ERROR ? ? - URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!
[code]....
View 5 Replies
View Related
Mar 16, 2013
I want to configure ASA 5510 with complete redundancy first time. I have already studied all material from cisco web site. but there are avalible alot of material. and i'm confused about the exact my requirment material.
This is current configuration:
active# sh running-config
: Saved
:
ASA Version 8.2(5)
[Code].....
View 10 Replies
View Related
Apr 5, 2013
I have some issue from last 2 month on sf300.
The problem is that sf300 does not support complete dhcp, for that i put different internet modem.
I connected one internet modem in vlan 1 so users from that vlan can access internet and default gateway is nothing but Internet modem ip. user in the vlan are not communicate with other vlan because, other vlan users default gateway is Interface ip address. How i can give access to vlan 1 to access other vlan .
See the attached.
I have to used static route in all 3 devices or any one.
View 4 Replies
View Related
Aug 5, 2012
I am configuring VPN on an 831 rotuer using a dynamic-map configuration. I can connect to the network and I can see phase 1 and 2 complete from the debugs however from what I can tell I can only ping across the VPN. I can't connect to and web services or RDP to any hosts on the local network. Here is a copy of my config.
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
service sequence-numbers
[code]....
View 6 Replies
View Related
Dec 27, 2012
After struggling with the setup of my new EA6500, I finally succeed in setting it up. Like other people in this forum, the setup process got interrupted approx., 90% in the setup process. After several factory resets and new setups, I finally was able to login locally to fulfill the setup and upgrade the firmware to 1.1.28.146072). After that, I do have wireless access, but the connection to my LAN connected NAS (Synology), is really really slow. Furthermore, when I try to use airplay to connect to my Airport express it drops out and starts blinking yellow? Finally, from time to time when I log in, I get the "No router found" message (can't remember the exact text). After a reboot I'm able to login. To me it seems that the firmware/router still is filled with a lots of bugs. I think I will downgrade to my old E4200, during the next couple of days, and return the EA6500.
View 1 Replies
View Related
