Cisco WAN :: GNS3 Additional BGP Process On Single Router
Jun 16, 2012
I need to be able to run more than one BGP routing process on my lab router. I have over connected BGP routers connected to my live production network and I need to emulate the production network with GNS3. However, BGP rules only allow a single BGP routing process on a single router. how to overcome this limitation for my lab?
I have two core switches - 4506E, and i noticed there are frequent cpu spikes on both of the cores switches. As its spikes intermitendly i couldnt able to anlyze the issue. I need inputs on the following,
1) Is there any Free CPU process monitoring tools to identify which process is spiking ?
2) Troubleshooting techniques to identify the issue.
I am trying to connect my Ubuntu PC with gns3 router using loopback interface tap0, I am trying to configure the ip address of tap0 by using gns3 router as DHCP Server. But I am finding it difficult to do so.
As my original Innbox V50U modem/router does not have a strong enough wifi signal I had to add in an additional wifi router - I used a Cisco Linksys E4200.The problem is that if I connect my laptop to the cisco router I can see the Innbox router but not vice versa. There is an additional problem as I have a wireless printer that is connected to the Cisco router. If I connect to the Innbox router I cannot use this printer as I cannot see its IP address.I read somewhere it might be down to the subnet mask. both are set to 255.255.255.0Apologies if this is n00b stuff but I have not had this problem before, I just naturally though the two networks would be able to talk to each-other.
I will be adding wireless access points or repeaters on a business network. The business already has one wireless router using a https login, that 15 computers are wired to, through switches. This Secure http router is directly connected to the cable modem.Would I be loosing the benefit of Secure http by adding wireless access points or repeaters that don't support it? Or would they be securely routed by the main https router connected to the gateway?I have never had the opportunity to work with a secure http router before.
i'm connecting to the internet using a desktop pc and a D-Link DSL-2560U (modem + wireless router). The wifi signal is very low on the other side of the house. I also have another wireless router - a Trendnet TEW-431BRP, and i want know if i can put it in the middle of the two areas of the house in order to boost the wifi signal in that area. How can i do it?
We have small which I'm looking to implement and have built this on GNS3.
We have:
Router A in site 1 Router B in site 2 Router C in site 3
Router A and B are connection via a point to point 100M link and from Router C we have a 2 point to point one of which is 5Mpbs and going to Router A and Router B.
For Router C to reach Router A network it will go via Router B and these are 100M connection. When the link between Router A and B goes down. Router C should update and start using the 5m route.
For some reson, the routes are not updating. I have to do 'clea ip eigrp ne' for the routes to update and if I reload the routers all works well, it seems the problem is intermittent.
Can a router connect to a switch to gain additional ports (to both access the internet AND to maintain an internal / home network)?IP line to house, connected to modem, connected to 4-port router, connected to 8-port switch. Now, each of six rooms in my house has one Cat-5e (RJ-45) jack whose run terminates to the switch. In some of these rooms, I need two wired devices (wireless isn't an option for the devices). Can I use the LAN port of a spare, wireless router (to also use as an access point for cell phones, etc) to plug into the jack and increase the number of ports in that room to have a functional LAN and WAN? I have read tons of info on plugging switches into routers to increase the number of ports, but not the other way around. Plus, ripping open walls to expand the network isn't feasible either. My other thought, would be to replace the switch with another (2nd) router, by connecting the 1st and 2nd routers together, and have the runs terminate to the open LAN ports of both routers --= and then expand the ports in those rooms by also using additional, spare wireless routers.
I have been using the E4200 for a few months now...and running access restrictions to cut down my kids internet hours.
Everything was working fine until today. I changed my Access Restriction password....and then discovered that I cannot 'Add' another device. The button is completely grayed out. I have other computers running on the network that are not in the Access Restriction list...so I should be able to click on 'Add' and select a device....
I can continue to edit the Access Restriction permissions for those devicescurrently in the list...but just cant Add any other device...
The last time I had to reconfigure the connections it took me hours!My son had to wipe his desktop clean and reinstall everything. Now when he tried to connect to the internet we can't get a connection at all. My desktop is still working fine as well as the wireless laptops.What do we have to do to get him reconnected?
I recently purchased an E-2500, but notice that in parental controls I can only block 6 or 8 websites. In my WRT54GS I could just create additional rules and they would work. But in this device I am limited on the sites that can be blocked per device. How I can block additional sites?
I'm using a SMC2804WBRP-G router connected to my ADSL-modem. Usually there are two computers connected to this router: a win7 ultimate desktop(wired) and a macbook air (wireless). Both working absolutely fine and never caused any connection drops as far as I know.
A new room mate moved in last month and each time she starts up her win7 home laptop the router looses the internet connection. The laptop is on a wired connection.
The first time she connected to my router, the connection dropped every 2 mins. To find out whats wrong with her machine I disabled all unnecessary services etc. besides the anti virus software. That worked to eliminate almost all of those periodic connection drops. But the start up drop remained and I've got the feeling that the router is still loosing connection from time to time.
I have AT&T Uverse which provides Internet for my home. The wireless capability of this router is pretty bad, I don't get good/reliable wireless reception upstairs in my office. The solution was to buy a Cisco E2500 and add it as an access point upstairs.
I have the E2500 LAN port connected to the LAN port of my uverse router downstairs. DHCP is turned off on the E2500. I have my office PC wired into the E2500. The home PC works fine, its getting DHCP from the uverse router downstairs and connects and good speeds. The problem comes with my wireless devices trying to connect to the E2500.
I should mention that yesterday when i bought this, all worked fine. This morning when I came into my office none of the wireless devices would connect to the E2500 at all. But as soon as I remove the cable that connects the E2500 to the uverse router downstairs they will connect via wireless but of course not get an IP address since that is disabled.
I have factory reset the E2500 and uverse router several times and am getting no where. what could be causing the wireless devices to not connect at all?
I have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. URL We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
I have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. [URL] According to our baseline it should not be more than 40% at any given time. We see high CPU uptp 70% consistently.
CPU utilization for five seconds: 99%/0%; one minute: 57%; five minutes: 55% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 442 66173704 90234125 733 96.86% 46.09% 46.30% 0 BGP Router 7 509291060 26330202 19342 1.17% 3.90% 2.99% 0 Check heaps
Router has 1 eBGP session with ISP from where it downloads whole IPv4 internet routing table and two IBGP session with other two rotuer. When I look at BGP summary table I see many updates received from ISP and sent out to IBGP neighbors. Also did debug BGP updates to confirm it.
We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.
%BGP-6-BIGCHUNK: Big chunk pool request 628 for community. Replenishing with malloc
I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
My 851W will not complete the boot up process, here is the output during bootup(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013. Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T14, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Wed 18-Aug-10 02:37 by prod_rel_teamImage text-base: 0x8002007C, data-base: 0x814ECE54This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
What the heck is key renewal? And why does it change every 3600 seconds? Does that mean my password will change? If so how do I connect additional devices to my Wi-Fi after the 3600 seconds?
I'm using GNS3 in order to revise CCNA, the RIP part But I don't know why, i'v got a pbl with the routage table, especially with the metric which is wrong I don't understand wy the metric is always 1, because it should be 2 or 3 according to the network.
I want to ping my GNS3 routers from my real LAN PCs. Right now I am able to ping those GNS3 routers from real PC on which GNS3 is installed. The network topology is something like this.
-IP of GNS3 PC on which GNS3 is installed. 192.168.1.102/24 default gateway of LAN: 192.168.1.1/24
I have created a loopback adapter and assigned the IP address of 192.168.1.200/24 (IP is also of same LAN) the cloud and virtual router is dragged and router interface is assigned the IP 192.168.1.201/24. I am able to ping my router interface from 192.168.1.102 (System on which GNS3 is installed). What I want is to ping my router's interface from other LAN PCs line 192.168.1.104, 192.168.105 or from my gateway 192.168.1.1.
I plan on replacing my linksys BEFW11S4 wireless router with a new linksys WRT120N wireless router. Should I completely remove and unplug the old router before inserting the startup CD and beginning the installation process for the new router?
I am trying to do a Multicast lab in gns3 with a tap interface in os x and a linux vm in virtualbox. The os x box is broadcasting to 224.1.1.1. I have verified IP connectivity. I am using PIM dense mode. When I perform a packet capture on the tap interface I see no traffic to 224.1.1.1. However when I ping 224.1.1.1 from os x I see the traffic. Attached is my topology
I test all devices using ping command, from ASA to router was fine (on both interface) but not to Host , and host to router was fine, but only on directly interface(F1/0), and to ASA was not success. am i miss something in my configuration?
I was just brushing up few things in GNS3 and after setting up an SLA.Now when I want to set the track ip I get not option for sla why??I am running c3725-adventerprisek9-mz.124-15.T5 shouldn't it be available?